전기 방열기가 국화재배온실의 난방에 미치는 영향

서원명 ( Won Myung Suh ),임재운 ( Jae Woon Leem ),김영주 ( Young Ju Kim ),민영봉 ( Young Bong Min ),김현태 ( Hyeon Tae Kim ),허무룡 ( Moo Ryong Huh ),윤용철 ( Yong Cheol Yoon ) 경상대학교 농업생명과학연구원(구 경상대학교 농업자원이용연구소) 2010 농업생명과학연구 Vol.44 No.4

경상대학교 교내에 설치되어 있는 1-2W형 온실을 대상으로 전기 방열기를 이용하여 국화 재배온실의 난방효과를 검토한 결과는 다음과 같다. 실험기간동안 최고, 평균 및 최저 외기온은 각각 -3.8~21.3℃, -5.2~16.1℃ 및 -12.5~14.4℃ 정도의 범위로 나타났으며, 온실 내외의 평균상대습도 각각 43.5~98.6% 및 35.2~100%로 나타났다. 12월 중순부터 2월 상순까지 최저 외기온은 대략 -5.0~-10.0℃ 전후로 나타나 진주기상대의 최근 자료와 비교하면 상대적으로 최저기온이 낮게 나타나는 경향이 있었다. 야간의 경우, 방열기 직하부의 엽온이 방열기 중간 지점에서 측정한 엽온 보다 크게 2~3℃정도 높게 나타나거나 또는 미미하지만 약간 높게 나타나는 경향이 있었다. 근권부의 경우, 직하부나 중간 지점에서의 온도 차이는 거의 없는 것으로 나타났고, 근권부의 최고온도와 기타 최고 온도의 발생 시점을 보면, 약 2시간정도의 지체현상이 있음을 알 수 있었다. 그리고 실험기간동안 난방에 소요된 총 소비전력량, 공급에너지 및 총 난방비는 각각 2,800kWh, 2,408,000kcal 및 112,000won 정도였다. 화석연료인 경유로 난방할 경우, 총 난방비는 224,500won 정도였다. 방열기를 이용하여 난방할 경우, 난방비를 약 50% 정도 줄일 수 있을 것으로 판단되었다. An analysis in heating effects of an electric radiator located in a 1-2W type chrysanthemum (3 cultivars) cultivation greenhouse installed in Gyeongsang National University drew the following conclusions. During the experiment period, the highest, average, and the lowest outside temperatures were in the ranges of -3.8~21.3℃, -5.2~16.1℃ and -12.5~14.4℃, respectively, and the average relative humidity inside and outside the greenhouses were in the ranges of 43.5~98.6% and 35.2~100%, respectively. From mid-December to early February, the lowest outside temperature was recorded as approximately -5.0~-10.0℃, which showed that it tended to be relatively lower than the temperatures recorded at the Jinju Meteorological Observatory. During the night, the leaf temperature measured directly under the radiator tended to be higher by 2~3℃ than that those at the middle point of the radiator, or higher by anegligible amount. In the case of root zone temperature, it was found that there was almost no difference between temperatures of the part directly under and the middle point, and the time when the highest temperature of root zone and other highest temperatures took place showed that there was about a 2-hour delay phenomenon. The total electricity consumption, energy supply and total heating cost during the experiment period were 2,800 kWh, 2,408,000 kcal and 112,000 won, respectively. When diesel, a kind of fossil fuel, was used as heating oil, the total heating cost was around 224,500 won. It was estimated that the total heating cost could be reduced by around 50% if a radiator was used.

저방사화강(JLF-1)의 고온 피로균열진전거동에 관한 연구

박원조,정재욱,허선철,허정원 경상대학교 해양산업연구소 2002 해양산업연구소보 Vol.15 No.-

The objective of this study is to investigate life and fatigue crack propagation in the Reduced Activation Ferritic steel(RAFs) JLF-1. Crack growth rate tests on compact tension specimen of thickness 12mm were conducted by using sinusoidal waveform. Compact tension specimens were used and crack growth rate da/dN and stress intensity factor range ΔK were analyzed concerning to the R value of 0.1, 0.3 and 0.5 In order to find out the value of ΔK, load amplitude constant method was applied by the standard fatigue testing method describes in ASTM E647-95a. The effects of stress ratio and specimen size on the fatigue crack growth propagation for JLF-1 steel were discussed within the Paris law. As the result of this study, fatigue crack growth rate increased with in creasing the load ratio, Consequently, fatigue crack propagation of half size specimen was similar to those of full size specimen at room temperature. Also, there was no difference between base metal and weld metal at room temperature and high temperature.(400℃)

장애학생 관련 변인에 따른 비장애 학생의 통합태도 연구

오원석 ( Won Seok Oh ),남경숙 ( Kyung Sook Nam ),허명진 ( Myung Jin Huh ) 한국특수교육문제연구소 2006 특수교육저널 : 이론과 실천 Vol.7 No.3

장애학생 관련 변인에 따른 비장애 학생의 통합교육에 대한 태도 및 장애학생에 대한 친근감을 알아보기 위하여 본 연구를 수행하였으며, 연구 대상은 대구광역시 초등학교 5개교15학급 477명을 선정하였다. 연구 결과 장애학생의 통합에 대한 비장애 학생의 태도에 영향을 미치는 변인은 장애유형, 장애학생 성별, 장애학생의 청결상태이며, 영향을 미치지 않는 변인으로는 장애학생 부모의 관심도, 장애아 가정의 경제적 수준 그리고 장애학생의 학습 능력인 것으로 나타났다. The purpose of this study is to determine the attitudes for integration education and the intimacy with disabled students of Nondisabled students influenced by disabled students. For such purpose, 477 students of 15 classes from 5 elementary schools located in Daegu Metropolitan City were selected as the object of this study. Integrated Attitudes was measured through an investigation equipment by Oh Won-Seok and Seo-Yeong Ran which adapted and modified a testing document called Inclusion of Students who are Deaf or Hard of Hearing Inventory (ISDHH) invented by Hsin-Ling Hung(2005). The result indicated that the factors which influence the Attitudes of nondisabled students regarding integration with disabled students are the type of injury, the gender and the cleanness of the disabled student. The factors which do not influence the above are interests of the disabled student``s parents, economic level of the family and the learning ability of the disabled student.

SCM에 의해 제조된 금속기 복합재료의 미끄럼마모 특성

이광영,박원조,허선철,박성호,허정원 경상대학교 해양산업연구소 2002 해양산업연구소보 Vol.15 No.-

AC4CH-based metal matrix composites with All_B_40_33w reinforcement have been produced using squeeze casting method. Metal matrix composite that is produced from matrix material AC4CH and inorganic binders SiO_2, Al_20_3 and TiO_2 are added to the metal matrix composite for strength so binding among the whisker can take place. In this paper, To test for tribo a pin-on-disk machine and lubricant is used without paraffine 8.2CST at room temperature which is 40℃. As the results of this study, the tribological properties of each specimen are more improved then AO4CH. The variation of coefficient resistance is more stable at the AC4CH, TiO_2, but the variation rates are higher at the inanimate binder

ApoB/ApoA-I ratio is independently associated with carotid atherosclerosis in type 2 diabetes mellitus with well-controlled LDL cholesterol levels

( Ji Eun Jun ),( Young Ju Choi ),( Yong-ho Lee ),( Dae Jung Kim ),( Seok Won Park ),( Byung Wook Huh ),( Eun Jig Lee ),( Sun-ha Jee ),( Kyu Yeon Hur ),( Sung Hee Choi ),( Kap Bum Huh ) 대한내과학회 2018 The Korean Journal of Internal Medicine Vol.33 No.1

Background/Aims: This study aimed to investigate whether the apolipoprotein (Apo) B/ApoA-I ratio is associated with carotid intima-media thickness (CIMT) in type 2 diabetes mellitus (T2DM) subjects with low density lipoprotein cholesterol (LDL-C) levels less than 100 mg/dL. Methods: This cross-sectional study included 845 subjects aged with T2DM 40 to 75 years who had visited Huh’s Diabetes Center in Seoul, Republic of Korea for CIMT measurement. Traditional fasting lipid profiles, ApoB and ApoA-I levels were examined. CIMT was measured at three points on the far wall of 1 cm long section of the common carotid artery in the proximity of the carotid bulb. The mean value of six measurements from right and left carotid arteries were used as the mean CIMT. In this study, carotid atherosclerosis was defined as having a focal plaque or diffuse thickening of the carotid wall (mean CIMT ≥ 1.0 mm) Results: The prevalence of carotid atherosclerosis increased with ApoB/ApoA-I ratio. The ApoB/ApoA-I ratio, expressed as both quartiles (odds ratio [OR], 2.14; 95% confidence interval [CI], 1.21 to 3.79; p for trend = 0.014) and continuous values (OR, 10.05; 95% CI, 3.26 to 30.97; p < 0.001), was significantly associated with a higher risk for carotid atherosclerosis, regardless of conventional cardiovascular disease risk factors. The optimal ApoB/ApoA-I ratio cutoff value for detecting carotid atherosclerosis was 0.57, based on receiver operating characteristic curve analysis with a sensitivity of 58.0% and a specificity of 55.1%. Conclusions: A high ApoB/ApoA-I ratio was significantly associated with carotid atherosclerosis in T2DM patients with LDL-C levels less than 100 mg/dL.

콜레라독소의 피하투여에 의한 생쥐의 림프절 및 비장내 B 및 T 림프구의 분포변화

이원규,박낙진,김종원,허영범,김정혜,안희경 대한해부학회 1995 Anatomy & Cell Biology Vol.28 No.2

15세기 우리말 이름마디 연구(Ⅲ) : -겹월에서 변형된 이름마디-

허원욱 건국대학교 1990 論文集 Vol.30 No.1

This thesis can be summarized as follows ; Nominal Clauses can be classified to 'Nominal Clauses that is transformed from simplex sentence of deep structure' and 'Nominal Clauses that is transformed from complex sentence of deep structure'. This thesis is for syntactic analysis of 'Nominal Clauses that is transformed from complex sentence' in 15th Century's Korean. Nominal Clauses can be functioned as erery component in sentence like noun. ◁표삽입▷(원문을 참조하세요) In Nominal Clauses, 「-o/u-」(-오/우-) is infallibly inserted. The grammatical informations of Nominal Clauses are only Tense (「-asi-」(-아시-」and Respect (「-isi-, -s∧p-」 (-으시 -, -□-」)). When simplex sentence of deep structure is transformed to Nominal Clauses of surface structure, 「-i」(「-이」) is sometimes transformed to 「∧i」(「-□」)

납이온이 잔틴 옥시다제 활성에 미치는 영향

허근,신억섭,이상훈,안원효 영남대학교 약품개발연구소 1996 영남대학교 약품개발연구소 연구업적집 Vol.6 No.-

This study was done to determine the effect of lead acetate on the activities of the hepatic cytosolic xanthine oxidase and aldehyde oxidase which were well known as oxygen free radical generating enzyme in vitro. Lead ion accelerated the formation of lipid peroxide and the increment of xanthine oxidase(type O) activity and the type conversion ration from xanthine dehydrogenase to xanthine oxidase dose-dependently. But xanthine dehydrogenase(type D) activity was decreased. Aldehyde oxidase activity was not changed by lead ion. These data suggested that lead-induced cellular toxicity may be concerned partially with xanthine oxidase mediated lipid peroxidation.

확장된 안면경부 피판을 이용한 협부 재건

허승호,양원용,홍성표,이두형 대한미용성형외과학회 1997 Archives of Aesthetic Plastic Surgery Vol.3 No.1

Together, the cheek and neck can be considered as a single anatomic location because skin vascularity, texture and thickness are similar. The cervicofacial flap has been described as the treatment of choice for the cheek defect because of its good mobility and excellent cosmetic result. However, if the defects on the cheek are wider than the length of palpebral fissure or extended to the lower two thirds of the cheek, the conventional cervicofacial flaps would be inadequate in size without the benefit of expansion. Tissue expansion of the cheek and neck is distinguished by a particularly high rate of complication. Prevention of various complications require careful planning and certain modifications in technique. We have used the following modifications and measures to prevent the complications and to maximize the expansion. 1) Whenever possible, expanders were placed over the rigid foundation such as mandible or posterior neck area after wide undermining. 2) Expanders were placed deep to platysma in the neck area. 3)Following optimal expansion, the further dissection extending to the clavicle and the posterior neck area was performed for optimal mobilization and draping of the expanded skin. 4) The expanded skin was advanced upward on the cervical portion and rotated forward on the cheek portion. 5) The flap should not be draped above the inferior orbital rim and postoperatively the pressure garments were applied to prevent drooping of the expanded skin. We experienced 21 cases of the expanded cervicofacial flaps with above surgical modifications and the expanded cervicofacial flaps can resurface the 95% of cheek defects with munimal complications and excellent cosmetic results.

사출성형에 있어서의 금형재료와 금형제조 및 보수 기술에 관한 연구

허근태,우원호,김진환 경성대학교 생산기술연구소 1997 생산기술연구지 Vol.4 No.-

The materials of the mold in the injection molding was affected a various elements. In general, the materials of the mold depended on the number of the shots and the manufucturing mold. The munufucturing of mold needed some techniqus, one of them, the hot runner system is very utility techniqu in the injection molding using the enpla resin. The most important feature of the molding is the conservation techniqu in the manufuctures.