전기 방열기가 국화재배온실의 난방에 미치는 영향

서원명 ( Won Myung Suh ),임재운 ( Jae Woon Leem ),김영주 ( Young Ju Kim ),민영봉 ( Young Bong Min ),김현태 ( Hyeon Tae Kim ),허무룡 ( Moo Ryong Huh ),윤용철 ( Yong Cheol Yoon ) 경상대학교 농업생명과학연구원(구 경상대학교 농업자원이용연구소) 2010 농업생명과학연구 Vol.44 No.4

경상대학교 교내에 설치되어 있는 1-2W형 온실을 대상으로 전기 방열기를 이용하여 국화 재배온실의 난방효과를 검토한 결과는 다음과 같다. 실험기간동안 최고, 평균 및 최저 외기온은 각각 -3.8~21.3℃, -5.2~16.1℃ 및 -12.5~14.4℃ 정도의 범위로 나타났으며, 온실 내외의 평균상대습도 각각 43.5~98.6% 및 35.2~100%로 나타났다. 12월 중순부터 2월 상순까지 최저 외기온은 대략 -5.0~-10.0℃ 전후로 나타나 진주기상대의 최근 자료와 비교하면 상대적으로 최저기온이 낮게 나타나는 경향이 있었다. 야간의 경우, 방열기 직하부의 엽온이 방열기 중간 지점에서 측정한 엽온 보다 크게 2~3℃정도 높게 나타나거나 또는 미미하지만 약간 높게 나타나는 경향이 있었다. 근권부의 경우, 직하부나 중간 지점에서의 온도 차이는 거의 없는 것으로 나타났고, 근권부의 최고온도와 기타 최고 온도의 발생 시점을 보면, 약 2시간정도의 지체현상이 있음을 알 수 있었다. 그리고 실험기간동안 난방에 소요된 총 소비전력량, 공급에너지 및 총 난방비는 각각 2,800kWh, 2,408,000kcal 및 112,000won 정도였다. 화석연료인 경유로 난방할 경우, 총 난방비는 224,500won 정도였다. 방열기를 이용하여 난방할 경우, 난방비를 약 50% 정도 줄일 수 있을 것으로 판단되었다. An analysis in heating effects of an electric radiator located in a 1-2W type chrysanthemum (3 cultivars) cultivation greenhouse installed in Gyeongsang National University drew the following conclusions. During the experiment period, the highest, average, and the lowest outside temperatures were in the ranges of -3.8~21.3℃, -5.2~16.1℃ and -12.5~14.4℃, respectively, and the average relative humidity inside and outside the greenhouses were in the ranges of 43.5~98.6% and 35.2~100%, respectively. From mid-December to early February, the lowest outside temperature was recorded as approximately -5.0~-10.0℃, which showed that it tended to be relatively lower than the temperatures recorded at the Jinju Meteorological Observatory. During the night, the leaf temperature measured directly under the radiator tended to be higher by 2~3℃ than that those at the middle point of the radiator, or higher by anegligible amount. In the case of root zone temperature, it was found that there was almost no difference between temperatures of the part directly under and the middle point, and the time when the highest temperature of root zone and other highest temperatures took place showed that there was about a 2-hour delay phenomenon. The total electricity consumption, energy supply and total heating cost during the experiment period were 2,800 kWh, 2,408,000 kcal and 112,000 won, respectively. When diesel, a kind of fossil fuel, was used as heating oil, the total heating cost was around 224,500 won. It was estimated that the total heating cost could be reduced by around 50% if a radiator was used.

급성대동맥박리증에서 수술전 경식도심초음파도의 역할

박성훈,원태희,원용순,한재진,안재호,이귀용 梨花女子大學校 醫科大學 醫科學硏究所 1999 EMJ (Ewha medical journal) Vol.22 No.1

급성대동맥박리증은, 특히 상행대동맥을 침범한 경우, 응급수술을 요하는 질환으로서 수술전 대동맥판의 손상여부, 질환의 범위, 내벽파열부위의 위치 및 가지혈관의 상태등을 파악하여 수술계획을 수립하여야 한다. 저자들은 상행대동맥을 침범한 3례의 급성대동맥박리증 환자에서 전산화단층촬영과 함께 수술전 또는 필요에 따라 수술후 경식도심초음파도를 시행하여 환자의 치료에 도움을 받았기에 문헌고찰과 함께 보고하는 바이다. Acute type A arotic dissection is a condition which requires emergency surgery. Surgeons want to know not only the extent of the disease but also the exact site of intimal tear as well as the presence of side branch involvement to plan the extent of surgery. Various non-invasive diagnostic tools(transthoracic and transesophageal echocardiography, conventional and spiral computed tomography and magnetic resonance imaging) and invasive angiography are available for the evaluation of the extent of dissection, site of intimal tear and side branch involvement. Each technique has its advantage and disadvantage. Especially, MRI has been accepted as a gold standard for the diagnosis of aortic dissection, but it is immobile and sometimes it cannot give us the information about the small intimal tear site. Transesophageal echocardiography has the advantage of movability and high resolution in addition to the ability of providing comprehensive information about the cardiac function. Because of these advantages, it has been widely utilized for the evaluation of patients with aortic dissection. We performed preoperative transesophageal echocardiography in addition to computed tomography in 3 cases of acute type A aortic dissection and report these cases with the review of articles.

우심방을 침범한 거대 비호지킨씨 림프종 1예

강상범,진승원,이은경,박용현,최용호,김용주,박준철,김재형,홍순조,최규보,권종범,원용순,박건,이은희 대한순환기학회 2000 Korean Circulation Journal Vol.30 No.4

야뇨증 환아들의 심리사회적 특성에 대한 다기관 연구 : 행동 및 정서 문제를 중심으로

조수철,김재원,신민섭,황준원,한상원,박관현,이상돈,김경도,김건석,서홍진,이유식,정재용,김영균,문두건,남궁미경,한창희,조원열,김영식,배기수,이종국,정우영,신의진 大韓神經精神醫學會 2005 신경정신의학 Vol.44 No.6

Objectives : The aim of this study was to examine the behavioral and emotional problems associated with nocturnal enuresis in Korean children. Methods : Three hundred eighteen children with nocturnal enuresis, together with their parents, completed the Child Behavior Checklist (CBCL), Disruptive Behavior Disorder Scale according to DSM-IV (DBDS), Children's Depression Inventory (CDI), State-Trait Anxiety Inventory for Children (STAIC), and Piers-Harris Children's Self-Concept Scale (PHCSC). Ninety-three normal students were selected as the control group. Results : Compared to the normal control group, the mean scores with regard to the withdrawn, social problems, attention problems, delinquent behavior, aggressive behavior, externalizing problems and total problems profiles were significantly higher in the nocturnal enuresis group according to the CBCL results. The nocturnal enuresis group also scored significantly higher in the ADHD and ODD profiles of the DBDS. The nocturnal enuresis group was more depressed and anxious than the control group according to the results of the CDI and STAI. The mean score of the PHCSC was significantly lower in the nocturnal enuresis group when compared to the normal control group. Conclusion : The results of this study suggest that children with nocturnal enuresis in Korea have clinically relevant behavioral and emotional problems. The findings support the link between nocturnal enuresis and psychopathology in Korean children.

Nortriptyline 제제의 생물학적 동등성에 관한 연구

신재국,차인준,장인진,정원석,김용식,박찬웅,신상구 大韓臨床藥理學會 1993 臨床藥理學會誌 Vol.1 No.1

고관절 전치환술시 응용프로그램을 이용한 수술 전 계획

원중희,김용민,최의성,손현철,박경진,남기세,정재중 대한고관절학회 2003 Hip and Pelvis Vol.15 No.3

복강경을 이용한 대장 부분 절제 시행 1예

박재갑,서경석,정회원,김선회,오용석,송인성,박용현 대한대장항문학회 1993 Annals of Coloproctolgy Vol.9 No.1

정상교합자의 치열궁 형태

권용철,성정옥,권오원,성재현 대한치과교정학회 1989 대한치과교정학회지 Vol.19 No.1

This study was designed to investigate dental arch shapes buccally and lingually at Bracket Level of Koreans. This involved studying 63 inviduals (37 males, 26 females) with normal occlusion ranging in age from 17 to 24 yesrs old. The landmarks were digitized and measurements and statistical analysis were performed by NEC 9801 V-M computer. The Results were as Follows: Bicanine width, Bipremolar width and Bimolar width were larger in males than in females. Buccal and lingual arch form and coordination form were obtained by NEC 9801 V-M computer. The parabolic equations which represents buccal and lingual arch form were obtained.

분무건조법을 이용한 방출 제어형 케토로락 고형지질마이크로스피어의 제제설계

윤재남,이은미,김동우,박용근,전일순,이계원,지웅길 충남대학교 약학대학 의약품개발연구소 2003 藥學論文集 Vol.18 No.-

Ketorolac (KA) and ketorolac tromethamine (KT) is the nonsteroidal anti-inflammatory drugs (NSAIDs) and has been used widely. To improve its frequent administration by control of drug release. we prepared SLM of KA and KT using Mirj 45 and 52 as surfactants and tripalmitin and tristearin as lipids by spry drying method SLM, as a disperse system for injection, were evaluated by measurement of particle sizes. SEM and drug release pattern As a result. spherical SLM were prepared and their particle size were in the range of 25-125 μm, which were dependant on the types and contents of lipid and sururfactants. Their dissolution rate were decreased as increasing lipid contents.

알루미늄 연속주조 용탕의 탈 가스 일체화 장치 개발

이용중,김태원,김기대,류재엽,이형우 한국공작기계학회 2004 한국공작기계학회 추계학술대회논문집 Vol.2004 No.-

It is necessary for managing a perfect process for degasing aluminum molten metal according to the increase of a grade of aluminum and its alloy products. There are some methods that have been used to manage a degasing process in recent years, such as an injection method that uses aluminum molten metal powder and chemicals supplier and input method that supplies argon and nitrogen, or chlorine gas by using a gas blow-tube. However, these methods show some problems, and it shows that it is a difficult process to handle, pollution due to the producing a lot of toxic gases like chlorine and fluoride gas, irregular effects, and lowering work efficiency due to the excessive processing time. The problems that are the most fatal are the producing a lot of sludge due to the reaction of aluminum molten metal with chemicals, loss of metals, and decreasing the life of refractory materials. In order to solve these problems, this paper develops a technology that is related to aluminum continuous casting molten metal and monolithic degasing apparatus. A degasing apparatus developed in this study improved the existing methods and prevented environmental pollution with smokeless, odorless, and harmlessness by using a new method that applies argon and nitrogen gas in which the methods used in the West and Japan are eliminated. The developed method can significantly reduce product faults that are caused by the production of gas and oxidation because it uses a preprocessed molten metal with chemicals. In addition, the amount of the produced sludge can also be reduced by 60~80% maximum compared with the existing methods. Then, it makes it possible to minimize the loss of metals. Moreover, the molten metal processing and settling time is also shortened by comparing it with the existing methods that are applied by using chemicals. In addition, it does much to improve the workers' health, safety and environment because there is no pollution. The improvement of productivity and prevention effects of disaster from the results of the development can be summarized as follows. It will contribute to the process rationalization because it does not have any unnecessary processes that the molten metal will be moved to an agitator by using a ladle and returned to process for degasing like the existing process due to the monolithic configuration. There are no floating impurities due to the oxidation caused by the contact with the air as same as the existing process. In addition, it can protect the blending of precipitation impurities. Because it has a monolithic configuration, it can avoid the use of additional energy to compensate the temperature decreasing about 60? that is caused by the moving of molten metal. It is not necessary to invest an extra facilities in order to discharge the gas generated from a degasing process by using an agitator. The working environment can be improved by the hospitable air in the factory because the molten metal is almost not exposed in the interior of the area.