판상형 충전제의 함량과 배향에 따른 PP복합체의 열팽창계수 영향 연구

이기윤(Kee Yoon Lee),이용현(Yong Hyun Lee),정선경(Sun Kyoung Jeoung),황효연(Hyo Yeon Hwang),이승구(Seung Goo Lee) 한국고분자학회 2012 폴리머 Vol.36 No.3

두 가지의 종횡비(ρα=a1/a3 and ρβ=a1/a2)에 의해 특징지어진 3차원 타원체(a1 > a2 > a3)를 사용하여 polypropylene 복합체의 판상형 충전제 함량과 방향이 열팽창률에 미치는 영향에 대해 실험적인 연구를 수행하였다. 측정된 실험적인 값은 Lee와 그의 연구자들이 제안한 이론적인 모델에 의한 계산 값과 비교분석되었다. 판상형충전제로는 운모와 탈크가 사용되었다. 실험 결과로 운모의 경우 종횡비는 ρα= 13.5, ρβ= 1.8이 사용되 어, 20 wt% 함량일때 α11/αm는 약 0.56으로 감소하였으나, α33/αm는 오히려 1.018로 증가함을 보였다. 탈크의 경우의 종횡비는 ρα=3.7, ρβ= 1.4이었고 α11/αm는 0.63으로 감소하였다. 결국 운모와 탈크 모두 그 함량증가에 따라 종단방향과 횡단방향에서 열팽창률은 감소하였으나 수직방향에서는 초기 낮은 충전제 함량에서는 오히려 증가하는 경향을 보였다. Experimental study was performed regarding the effects of disc-like filler orientation and contents on the coefficient of thermal expansion (CTE) of polypropylene composites using the three dimensional ellipsoids (a1 > a2 > a3) analyzed by two aspect ratios(ρα=a1/a3 and ρβ=a1/a2). Measured data were compared with the theoretical approaches proposed by Lee et al. Mica and talc were useed as disk-like fillers in the composites. As experimental results, α11/αm decreased down to ca. 0.56 with mica content of 20 wt% and the aspect ratios, ρα=13.5, ρβ=1.8. However, α33/αm increased to more than 1. In the case of talc, α11/αm decreased to ca. 0.63 with 20 wt% and ρα=3.7, ρβ=1.4. Finally, the longitudinal CTEs (α11) of polypropylene composites decreased as filler contents increased, but normal CTE (α33) increased in the low filler contents like the theory.

Plant regeneration from callus of Iris odaesanensis Y. N. Lee native to Korea via organogenesis

Bae, Kee-Hwa,Yoo, Kyoung-Hwa,Lee, Mi-Hyun,Jeong, Jae-Hun,Choi, Yong-Eui,Yoon, Eui-Soo The Korean Society of Plant Biotechnology 2013 식물생명공학회지 Vol.40 No.3

Iris odaesanensis Y. N. Lee. is an important endangered and native plant belonging to the family Iridaceae in Korea. This study describes a method for rapid micropropagation of this species via from leaf, rhizome and root explants derived calli. Leaf, rhizome and root explants were cultured on Murashige and Skoog (MS) medium supplemented with 2,4-dichlorophenoxy acetic acid (2,4-D) for callus induction. Rhizome explants yielded calli at a frequency of 72% when cultured at 1.0 mg/l 2,4-D. Calli were maintained at 1.0 mg/l 2,4-D. These calli were transferred to MS medium supplemented with 0, 0.5, 1.0, and 2.0 mg/l 2,4-D in combination with 0, 0.5, 1.0, and 3.0 mg/l BA for adventitious shoot induction. The highest number of adventitious shoot (228.9 per petri-dish) were formed at 1.0 mg/l 2,4-D and 1.0 mg/l BA. WPM medium was the best to convert calli into plantlets, where up to 98.2% of calli were regenerated into plantlets. This in vitro propagation protocol should be useful for conservation of this endangered plant.

판상형 충전제의 함량과 배향에 따른 PP복합체의 영률 변화 연구

서상범(Sang Bum Seo),이용현(Yong Hyun Lee),정선경(Sun Kyoung Jeong),이승구(Seung Goo Lee),이기윤(Kee Yoon Lee) 한국고분자학회 2012 폴리머 Vol.36 No.2

이 논문은 판상형 충전제의 함량과 배향에 따라 폴리프로필렌 복합체의 영률 변화에 미치는 영향을 연구 하였다. 이론적인 예측은 Lee와 그의 연구자들에 의해 제안된 두 개의 종횡비, ρα=a1/a3과 ρβ=a1/a2 를 이용하여 3차원 타원체의 형상을 계산하였고 실험값과 비교 분석하였다. 판상형 충전제로 운모와 탈크를 사용하였다. 충전제의 형태는 SEM을 이용해 관찰하였고, 종횡비는 고분자의 흐름을 기준으로 좌표축을 설정하여 통계적 방법으로 계 산하였다. 충전제가 운모인 경우에 ρα=13.5와 ρβ=1.8이었고, 탈크의 경우는 ρα=3.8과 ρβ=1.4이었다. 또한 충전제 의 2개의 종횡비와 함량이 기계적 물성에 미치는 영향을 실험적으로 연구하였다. 운모의 경우 30 wt% 함량일 때 E11이 약 2.7배 향상되었다. 탈크의 경우는 E11이 약 2.3배 향상하였다. This paper studied the effects of the content and the orientation of the disk shape fillers on the modulus of PP composites. The experimental results were compared with the theoretical calculations which included the three dimensional ellipsoids and analyzed by two aspect ratios, ρα=a1/a3 and ρβ=a1/a2 proposed by Lee and his researchers. Mica and talc were used as disk shape fillers in the composites. The shapes of mica and talc were observed by SEM and aspect ratios were statistically calculated. For the case of mica, the average aspect ratios were ρα=13.5 and ρβ=1.8, and for the case of talc, they were ρα=3.8 and ρβ=1.4. Also, the effects of two aspect ratios and the content of filler on the mechanical properties were studied: For 30 wt% of mica, E11 increased up to about 2.7 times, and for the other case of talc, E11 increased up to about 2.3 times, respectively.

Magnetron sputtering법으로 제조된 Al-1%Cu/Tungsten Nitride 다층 박막

이기선,서수정,김장현,김남철 공주대학교 자원재활용신소재지역협력센터 2000 2차년도 센터 사업 성과집 Vol.2000 No.1

표면 탄성파 디바이스의 전극재료로 사용되는 Al-1%Cu(4000Å)/tungsten nitride 박막을 magnetron sputtering법으로 제조하고 전기저항을 평가한 결과 비정질상의 tungsten nitride 박막을 제조할 수 있었고, 비정질 형성을 위해서 질소비 (R = N2/(Ar+N2))가 10∼40% 정도 필요하였다. Tungsten nitride 박막의 잔류응력은 비정질이 형성되면서 급격히 감소되었다. 이러한 비정질 박막위에 Al-1%Cu합금막이 형성되었다. 다층막은 453K에서 4시간 동안 열처리함으로써 3.6μΩ-cm의 저항를 나타냈는데, 이는 박막내 결정립 성장과 결정 결함의 감소에 기인하였다. As a power durable-electrode in SAW filter. Al-1%Cu/tungsten nitride multi-layer thin film was fabricated by magnetron sputtering process. Tungsten nitride films had the amorphours phase at the nitrogen ratio, R, ranging from 10~40%. The amorphization could be controlled by nitrogen ratio. R = N2/(N2+Ar) as a sputtering process parameter. Residual stress in tungsten nitride abruptly decreased with the formation of amorphous phase. Al-1%Cu thin film was deposited on the amorphous tungsten nitride. After the multi-layed thin film was annealed for 4 hours at 453K, the resistivity decreased as 3.6 μΩ-cm, which was due to grain growth and reduced crystal defects.

油脂의 새로운 誘導體에 關한 硏究[Ⅰ] : 피마자油의 에스텔化物의 合成 Synthesis of the Ester Compound of Caster Oil

李容億,李基賢 명지대학교 1976 明大論文集 Vol.9 No.-

New type products of castor oil and fatty acid groups were synthesized and their properties were investigated whether they have solubility. Relative proportions of structual building units of those properties were determined, and also the functions of their properties were determined whether they were induced by the caster oil/fatty acid mole ratio. Results were discussed.

장루 보유자의 생활 만족도 조사

서현석,이석환,고영관,오수명,윤충,주흥재,이기형 대한대장항문학회 1998 Annals of Coloproctolgy Vol.14 No.3

HIV 감염 환자에서 발생한 편평 콘딜롬 1예

이해웅,오상현,장성은,최지호,문기찬,고재경 대한피부과학회 2006 大韓皮膚科學會誌 Vol.44 No.4

齒科嬌正用線材의 物理的 性質에 미치는 熱處理의 影響

李基大,權五源,成材鉉 慶北大學校 齒科大學 1985 慶北齒大論文集 Vol.2 No.1

The physical properties of .016" orthodontic wires by heat treatment were studied in tension, bending, hardness and microstructures. The wires were tested in the as-manufactured and heat-treated conditions. The results were as follows: Ultimate tensile strength and yield strength were slightly increased by heat treatment, but Elgiloy was the most effective by geat treatment. The strength of Elgiloy showed the highest value after heat treatment above 6 minutes at 500, 600℃. Also, bending fluxure modulus of elasticity were progressively increased by heat treatment. the hardness number of Australian of as-manufactured wires showed the highest value, and Elgiloy showed the highest value by heat treatment. Microstructure of as-manufactured wires showed fibrous interlocking grains, and a coarse grains after heat treatment and an austenite structure after solution heat treatment.

횡성댐 水沒地域內의 植生에 關한 硏究 : 移植對象區域을 中心으로 Centered with Subdivided Area to Select Plants Capable of Transfer

이우철,이기의,서옥하,조현길,백원기,김경진 江原大學校 森林科學硏究所 1997 Journal of Forest Science Vol.13 No.-

본 조사 연구는 江原道 橫成郡 甲川面과 橫成邑 일부를 포함하는 지역에 횡성댐이 건설됨에 따라 수몰되어질 自然生態系의 復元과 保存計劃의 일부로 수행되어졌다. 移植對象區域인 7개소를 중심으로 綠地自然度, 植生現存量 및 생산량 種組成과 植生에 관해 조사하였으며 그 결과는 다음과 같다. 1. 綠地自然度를 등급별로 사정한 결과 등급 0(3.01%), 1(5.3%), 2(28.2%), 3(0.1%), 5(0.2%), 7(4.6%), 7(44.7%), 및 8(13.8%)의 8개 등급으로 구분되었다. 2. 전체조사지역의 現存量과 生産量은 각각 88,436.3 ton/year 과 12,960.3 ton/year 이었다. 3. 조사지역의 陸上植物의 種組成은 86科, 221屬, 306種, 1變種, 3品種의 총 310種으로 조사되었다. 4. 선정된 7개의 植生調査地點에서는 소나무군락이 憂占하며, 그밖에 신갈나무군락, 떡갈나무군락, 상수리나무군락으로 나타났다. This study was carried out in a part of conservative plans recovering natural ecosystem which will be submerged, as Hoengseong dam is being constructed around Hoengseong-Eup and Gabcheon-Myun. The submerged area was divided into 7 small areas to figure out what kinds of species of plants are and will be according to detailed geographic characteristics. In the center of the subdivided areas. Degree of Green Naturality, standing biomass, net 36production per year, and composition of plant species were investigated. The results are as following; 1. The surveyed area was classified into 8 degree by Degree of Green Naturality, and the appeared degree and the rate of occupation were 0(3.01%), 1(5.3%), 2(28.2%), 3(0.1%), 5(0.2%), 7(4.6%), 7(44.7%), 및 8(13.8%). 2. Standing biomass was 88,436.3 ton/year and net production per year was 12,960.3 ton/year. 3. The list of vascular plants identified in this study consisted of 86 families, 221genera, 1 variety, 3 formae and 306 species, totally summiting upto 310 species. 4. The 7 surveyed areas were largely occupied by Pinus community. In addition, there were Quercus mongolica, Quercus dentata, and Quercus acutissima communities.

NACK 폭주 억제를 이용한 SRM 성능 개선

李演洙,金泰勳,朴惠蓮,李基鉉 明知大學校 産業技術硏究所 2003 産業技術硏究所論文集 Vol.22 No.-

In this paper, we deal with the Negative Acknowledgement(NACK)-Implosion problem that arises in the multicasting environment, and present a scheme to cope with this problem, the modified version of the Scalable Reliable Multicast(SRM) protocol, called SRM-K. This motivates this work in which the NACK message are generated depending on the congestion level inside the network. The occurrence of congestion is determined by estimating the round trip time (RTT) for each message. As an indication of the congestion level, we introduce a counter in each node, whose value K in dynamically adapted to the change of the network situation, namely increases when the congestion builds up and decreases otherwise. The proposed SRM-K scheme is evaluated by performing the simulation, showing that it outperforms the SRM, in particular, in the scenario when the network situation dynamically varies.