동일한 시료에 대한 국내 기관간의 STR 분석결과 비교 : STR 유전자좌 분석법의 표준화 설정을 위하여

박종태,신경진,양윤석,우광만,이숭덕,이승환,이정빈,정연보,조승희,한길로,한면수,홍승범 大韓法醫學會 2001 대한법의학회지 Vol.25 No.1

This paper described a collaborative exercise intended to see what kinds of short tandem repeat (STR) loci are used in different DNA typing laboratories in Korea and to compare their results for the demonstration whether uniformity of DNA profiling results from different laboratory could be achieved in Korea Laboratories were asked to test five tissue DNAs using methods routinely used in each laboratory and to report the results to the coordinating laboratory. The exercise demonstrated that each laboratory was using different STR loci for the typing with different STR numbers,2 VNTRS,36 STRs and amelogenin in total, and the direct comparison of the results from all the laboratory for the 18 loci could not be done as only one laboratory submitted typing results. Among 21 loci for which several laboratories submitted typing results, results for 14 loci were the same and results for the other 7 loci were different depending on the participating laboratory. D1S80, F13A01, D16S539, D21S11, D18S51, D3S1744 were the loci with different typing results. Even in the cases where commercial kits were used, the results were not the same depending on the machines used, that is the capillary electrophoresis or the gel based electrophoresis. The reason for the different results, points about the standardization of the methods arid the profiling data were described.

마스낵 제조를 위한 당절임 공정의 최적화

한주영,김남우,황성희,윤광섭,신승렬 한국식품저장유통학회 ( 구 한국농산물저장유통학회 ) 2003 한국식품저장유통학회지 Vol.10 No.3

대부분의 마는 건조분말제품으로 가공되고 있는데, 마를 다양한 가공품으로 개발하기 위한 방법의 하나로 삼투건조라는 전처리를 행하여 건조에 의한 품질손상을 억제하고 단맛으로 기호성을 높인 건조 마 제품을 얻을 수 있는 당절임 공정의 최적화를 시도하여 최적조건을 얻고자 하였다. 침지시간을 3-7시간, 온도는 20-60℃, 당농도는 30-70%로 하는 중심합성계획법으로 실험을 설계하여 최적화하였다. 이때의 종속변수로는 침지 후 수분함량, 당도, 색도, 그리고 동결건조후의 수분함량과 재수화율로 하여 분석한 결과 동결건조 후 수분함량에 대해서는 유의성이 없었다. 세 가지의 공정변수 중 온도의 영향이 가장 적어 온도를 중심으로 고정한 후 침지시간과 당농도의 최적조건을 찾은 결과, 수분함량을 66-70%, 당도를 25-30%, L 75이상, a-2.1-2.4, b를 5이상 그리고 재수화율을 200-250을 제한 조건으로 하는 조건으로 하는 영역은 5.2-5.9시간, 56-61%로 나타났다. This study was conducted to the optimize sugaring process of yam for development of new snack product and enhancement acceptability. Three variables by five level central composite design and response surface methodology were used to determine optimum conditions for sugaring time, temperature and concentration. Optimization of the process was conducted using the combination of the moisture content, solid content, color and rehydration ratio. The regression polynomial model was suitable (P>0.05) model by Lack-of-Fit analysis with highly significant. To optimize the process, based on surface response and contour plots, superimposing the individual contour plots for the response variables. The optimum conditions for this process were 5.5 hours and 58% at 40℃ under the optimum of restricted variables as moisture content was 66 to 70, solid content was 25 to 30%, L value was above 75, a value was -2.1 to -2.4, b value was above 5 and rehydration ratio was 200 to 250.

GT rotary file을 이용한 만곡 근관형성시 작업 효율 및 file 변형 발생에 관한 연구

신주희,백승호,배광식,임성삼,윤수한,김병현 대한치과보존학회 2001 Restorative Dentistry & Endodontics Vol.26 No.5

Root canal preparation process is of utmost importance in successful treatment of root canal. Also, one of the most important purpose of the root canal preparation is to enlarge the root canal three dimensionally without changing the curvature of the root canal. However, as the curvature of the root canal increases, there are many difficulties involved in formation of optimum root canal. Therefore, in order to solve the above mentioned problems, new developments in methods of root canal preparation and equipments for such purposes were made. Recently, vigorous studies about newly introduced engine-driven nitckel-ti-tanium rotary file are conducted. As shown in research results to dates, it is well established that the use of nickel-titanium file is better suited for curved root canal than stainless steel file in maintaining the curvature of root canal and reducing the deformation of root canal. However, it is also acknowledged that there are a few discrepancies in research results according to protocol, due to failure to remove variables in experiments. In addition, although it is recommended by the manufacturer that the GT rotary file should maintain a low rotational speed of 150∼350rpm and 'light pressure' as light as not to break the lead of a pencil, academic studies about the vertical force which is not yet standardized are not sufficiently explored. Therefore, this research devised and utilized a special research equipment to standardize the appropriate range of vertical force for GT rotary file through experiments by breaking of the lead of a pencil as expressed by the manufacturer and to accurately measure factors involved through repeating and recreating the environment of root canal preparation. Forming nine experimental groups by varying the vertical forces (150g, 220g, 300g) and rpm (150rpm, 250rpm, 350rpm), the effects of changing vertical forces and rpm on working efficiency were measured in terms of time expended in root canal preparation by crown-down method using a transparent resin block with 35 degree curvature and GT rotary file (z-test). The following research using this special research equipment that involved nine experimental groups and varying the vertical force for root canal preparation from 300g which is within the normal vertical force range to 700g and 1000g which fall outside the normal rpm range. The results were as follows : 1.Analysis of the experiment results revealed that the tome spent in root canal preparation decreased as the vertical forces and rpm increased (p<0.05). Also, the effects of rpm were greater than those of the vertical forces within the normal vertical force range (β-weight test) . 2.Observation of the deformation of GT rotary file revealed that deformation increases in a direct correlation with the vertical force increase and in a reverse correlation with the rpm decrease, In the case of the vertical forces close to the normal range, the probability of GT rotary file deformation were quite different depending on the rpm changes. In the case of◎eater tier◎cal forces, the occurrences of deformation of the file were more frequent regardless of the rpm changes. 3.Deformation and breakage of file were also commonly observed in the expended time measurement experiments and GT rotary file deformation experiments in which low speed rpm (150rpm) was used and at the curved portion of the resin block. Key words : GT rotary file, Crown-down method, Working efficiency, Vertical force, Rpm, Deformation and breakage of file

강재 슬릿형 댐퍼를 부착한 철근콘크리트조 골조의 거동

신종익,이정한,송한범,강대언,오상훈,차승렬,이용재,김상대,이원호 대한건축학회 2004 대한건축학회 학술발표대회 논문집 - 계획계/구조계 Vol.24 No.1(구조계)

This study investigates the performance of the reinforced concrete frame with the steel plate slit damper. The test was carried out to investigate the structural behavior between the reinforced concrete bare frame and the reinforced concrete frame with the steel plate slit damper. The test results showed that the energy absorption capacity of the damped-frame was several times larger than that of the bare frame. For the damage by the input energy is concentrated on the steel plate slit damper, the ductilities of the former structure were increased and the damaged frame can be reused after exchange the steel plate slit damper.

다발성 동맥류와 혈전증을 동반한 베체트병 1예

신표진,김장영,이승환,윤정한 대한순환기학회 1998 Korean Circulation Journal Vol.28 No.8

A Digital Watermark

신정화,김인택,한승수 명지대학교 산업기술연구소 2001 産業技術硏究所論文集 Vol.20 No.-

In this paper, watermark technique has been proposed as a method to hide secret information into the signals so as to discourage unauthorized copying or attest the origin of the media. We present an approach for still image watermarking in which the watermark is embedded in the middle frequence area. It is confirmed from numerical experiments that the proposed method yields the watermarked image which is robust to several attacks.

운동실조를 동반하지 않은 급성외안근마비 1례

신대수,이승회,이한샘,박성욱,박현영,장혁,김요식,조광호 圓光大學校 醫科學硏究所 2004 圓光醫科學 Vol.19 No.2

제7차 고등학교 체육과교육과정에 대한 인식

신승호,한상준 江原大學校附設體育科學硏究所 2003 江原大學校附設體育科學硏究所論文集 Vol.- No.26

The purpose of this study was to examine how much the high school students understand the 7th physical education curriculum, to find out the better teaching method for physical training class and to give basic data needed for using selection focused curriculum. To attain this purpose, this paper dealt with the survey with the 1st-2nd grade students, 1173 students who live in cities and counties whose population is more than 200,000 and less than 100,000. The results are as follows. Most students felt positive about the structures and class aims of the 7th curriculum in high school physical education. boy students and high graded group had relatively higher regards and participation of the 7th physical education curriculum. They also had positive regards about the present physical training evaluation. In other words, boy students, high graded group and county's group had more positive thought about the evaluation process and results of the physical training class than girl students, low graded group and city's group.

유리폐기물과 하수슬러지 소각재의 고형화 처리연구

한상목,신대용,윤봉구,김승겸 강원대학교 부설 석재복합신소재 제품연구센터 2002 석재연 논문집 Vol.7 No.-

하수슬러지 소각재, 폐유리분말 및 고로슬래그의 고형화에 의하여 건자재를 제조하였다. 하수슬러지 소각재는 SiO_2와 Al_2O_3가 75 wt%, Fe_2O_3가 8.21 wt%, 폐유리분말은 SiO_2 71.4 wt%, Na_2O 14.43 wt% 및 CaO 9.32 wt%, 고로슬래그는 SiO_2 33.4 wt%, CaO 41 wt% 및 Al_2O_3 14.5 wt%를 함유하여 세라믹스 제조원료로 사용이 가능하였다. 하수슬러지를 800℃에서 2시간 하소한 무기질분말을 분쇄하여 하수슬러지 소각재를 제조하였다. 30∼70 wt%의 하수슬러지 소각재, 30∼70 wt%의 폐유리분말 및 10∼30 wt%의 고로슬래그를 혼함하여 950∼1,100℃에서 2시간 소성하여 시편을 제조하였다. 하수슬러지 소각재 첨가량이 감소하고 폐유리분말의 첨가량과 소성온도가 증가하면 부피비중과 압축강도는 증가하였으나 기공률과 흡수율은 감소하였다. 1,050℃에서 소성한 시편(No. 1, 3, 5 및 7)의 부피비중은 1.70∼1.83, 기공률과 흡수율은 0.3∼2.4% 및 0.1∼1.5%, 압축강도 272∼323 kgf/㎠을 나타내었다. 고로슬래그를 첨가하여 1,100℃로 소성한 시편(No. 8, 9, 및 10)의 부피비중은 1.82∼2.11 및 압축강도는 350∼671 kgf/㎠이었다. 하수슬러지 소각재, 고로슬래그 및 시편의 중금속출량은 매립지 침출수배출 허용기준치보다 낮아, 본 연구에서 제조한 시편은 주변 환경에 해가 없어 건자재로의 이용이 가능하였다. An experimental study for the constructional material by solidification using sewage sludge ash, waste glass powder and blast furnace slag was carried out in the senses of waste materials disposal and utilization. The reusability of sewage sludge ash, waste glass powder and blast furnace slag as a raw material in the manufacturing process of ceramics was highly expected because the chemical compositions of these waste materials were mostly SiO_2 and Al_2O_3. Sewage sludge ash was fabricated by calcined at 800℃ for 2 hours and obtained by the crushing. The mixture of 30∼70wt% of sewage sludge ash, 30∼70 wt% of waste glass powder and 10∼30 wt% of blast furnace slag were heated at 950∼1,100℃ for 2 hours. The density and the compressive strength of specimen increased with increasing the sintering temperature and decreasing the addition amount of sewage sludge ash, No. 1, 3, 5 and 7 specimens showed the bulk density of 1.70∼1.83, porosity of 0.3∼2.4%, water absorption of 0.1∼1.5% and compressive strength of 272∼323kgf/㎠. And, that of the No. 7 specimen heated at 1,100℃ increased with increasing the addition amount of blast furnace slag, and for No. 8, 9 and 10 specimens, bulk density was 1.82∼2.11 and compressive strength was 350∼671 kgf/㎠. An extraction test for specimen to detect toxic materials showed below the permitted standard of land-filling extractable heavy metal contents. It was founded that the specimen were useful for the constructional materials.

새로운 유사 원자층 증착 방법에 의한 산화막의 형성 및 터널링 자기 접합에의 응용

한신희,정원철,이장식,김병동,주승기 대한금속재료학회 2003 대한금속·재료학회지 Vol.41 No.1

The tunneling barrier is crucial to the overall performance in magnetic tunnel junction. We have suggested a new formation method for the tunnel barrier, which has utilized pseudo atomic layer deposition with sputtering (PALDS). As is well known, all metallic thin films oxidize more or less under atmospheric conditions. With using this property of metallic thin films, we have prepared tunnel barrier by sputtering metallic thin film and exposing it to the oxygen ambience. From transmission electron microscopy (TEM) observation, the formed tunnel barrier has been confirmed to have clear and good interface between magnetic layers and tunnel barrier. From atomic force microscopy (AFM) observation, it has been also confirmed to have low surface roughness. The TMR MRAM cell manufactured using PALDS method has been shown to exhibit typical tunnel resistance of 86 KΩ·μm^2 and TMR ratio of about 40%. The 40% of MR is quite large. It is considered that this value is geometrically enhanced magnetoresistance due to the low junction resistance of MTJ.