클럽 샤프트(Club Shaft) 특성에 따른 골프 스윙(Golf Swing)동작 분석

김성일,김기형,김형수,이현섭,김진욱,안찬규,김희진 한국운동역학회 2002 한국운동역학회지 Vol.12 No.2

본 연구는 클럽 샤프트의 대표적인 재질인 그라파이트(graphite)의 유연한(flexible) 클럽 샤프트(club shaft)의 특성에 따라 피험자가 운동학적(kinematics) 요인이 되는 관절의 각변위, 각속도, 각가속도, 클럽헤드의 속도와 가속도와 같은 변인들이 어떻게 적응하는지 비교 분석하여 보다 효율적인 드라이버 선택에 도움을 주며 샤프트 특성에 따른 신체관절의 움직임에 대한 자료를 제시하고자 하였다. 고속 카메라 2대의 속도는 500fps로 하였고 각 regylar,stiff, x-stiff, 자신의 클럽을 포함 각 4개의 클럽을 사용하여 각 클럽당 3번씩 촬영하였으며 목표방향에서 20m이상 벗어나는 경우의 촬영은 다시 촬영하였다. 본 연구에서는 디지타이징(digitizing)을 신체 9개 마커는 강체로 가정된 클럽과 신체분절 모델로 정의하였으며 2 대의 카메라(500fps)로부터 얻은 avi화일을 컴퓨터에 저장하고 자료로부터 Butterworth 6th order recursive digital filter를 사용하여 1차 자료를 smoothing 하고 DLT를 이용하여 3차원 좌표를 구성하도록 한다. 좌표값을 얻기 위하여 kwon3d v3.0을 이용하였다. 본 실험은 피험자 스스로 클럽의 특성에 따라 스윙의 속도를 달리 하기 때문에 스윙의 시간이 달라지며 어느 정도 클럽이 강성에 따라 스윙시간이 빨라지는 결과로 나타났다. 이것은 피험자가 샤프트가 강성(stiffness)에 따라 스윙 속도를 빨리 하게 되는 원인이 되는 것으로 생각된다. 어깨의 각변위는 클럽이 regular의 경우 임팩트에서 각속도를 계속 유지하고 있으며 stiff, x-stiff의 경우에는 어깨의 움직임이 임팩트에서 급격하게 감소되는 것을 알 수 있다. 이것은 팔의 동작과 클럽의 힘을 크게 하기 위한 동작으로 생각된다. 어깨 각속도는 클럽이 stiff할수록 각속도가 큰 감속하는 것으로 나타났다. 손목속도는 regular 클럽의 경우 손목의 감속이 늦게 되고 임팩트에서 손목의 감속이 적게 하는 것으로 나타났으며 stiff와 x-stiff의 클럽에서 임팩트 시에 순간적인 감가속으로 인해 클럽의 속도를 증가시키고 있다. 임팩트 시에 손목의 감가속은 클럽헤드의 임팩트 시 속도를 증가시키는 결과를 보였다. 클럽헤드는 regular 클럽이 임팩트전에는 속도 증가가 커지는 결과와 일치된 결과를 보이고 있다. The purpose of this study was to find the rational method to analyze golf swing with specific property of club shaft. Three subjects were filmed by two high speed digital cameras with 500fps. The phase analyzed was downswing of each subject. The three-dimensional coordinates of the anatomical landmarks were obtained with motion analysis system Kwon3d 3.0 version and smoothed by lowpass digital filter with cutoff frequency 6Hz. From these data, kinematic and kinetic variables were calculated using Matlab(ver 5.0) The variables for this study were angular velocity and accelerations, which were calculated and following conclusions have been made : 1) Golf swing time of stiff club is faster than that of regular club. 2) In shoulder joint motion of swing with the stiff club, x-stiff showed mort rapid negative acceleration than that of regular club. 3) In regular club, the velocity of club head would be more effective velocity, which was increasing, than those of other clubs before impact. 4) In wrist joint motion of swing with stiff club, x-stiff club showed faster than regular club in the downswing and impact more rapid negative acceleration.

선택적 후근절제술의 수술중 근전도 감시방법과 치료효과

김형일,김연희,김완호,김근수,김동찬 대한신경외과학회 1996 Journal of Korean neurosurgical society Vol.25 No.10

Selective posterior rhizotomy(SPR) has been known to reduce the spasticity as well as to improve the quality of life in patients with intractable spasticity. Twenty patients underwent SPR under intraoperative electrophysiological monitoring(IOM). Fifty-two percent of sacrolumbar rootlet were cut after electrical stimulation. Eighteen patients(90%) with spastic type of cerebral palsy showed marked reduction of spasticity and functional improvement without any complication. The patients who did not respond to SRP had mixed types of spasticity. IOM facilitate the selection of pathological rootlets regardless of anaesthetic level. intensity of electrical stimulation, and individual variability of responses. It is concluded that careful selection of surgical candidates and of pathological rootlets under IOM are important to reduce the spasticity. thereby to obtain a better outcome.

전도된 형이상학과 경험세계의 파편들, 그리고 深淵 : Derrida와 僧肇를 통해 본 해체의 심연과 전망

김형찬 翰林大學校 泰東古典硏究所 1993 泰東古典硏究 Vol.10 No.-

Characterization of Antihypertensive Angiotensin I-Converting Enzyme Inhibitor from Recombinant E. coli

Kim, Jae-Ho,Jeong, Seung-Chan,Lee, Dae-Hyoung,Lee, Jong-Soo 배재대학교 자연과학연구소 2005 自然科學論文集 Vol.16 No.1

안지오텐신(ACE) 저해제는 항고혈 효과를 갖고 있으므로 오랫동안 고혈압의 예방이나 치료에 이용되어 왔다. 본 연구는 재조합 대장균으로부터 새로운 ACE 저해제를 생산하고 정제하며 나아가 이들이 구조-기능 관P를 규명하기 위해 수행되었다. Saccharomyces cerevisiase의 ACE 저해 펩타이드 유전자를 함유하고 있는 재조합 pGEX-4T-3을 대장균 BL21(DE3)로 형질전환 시켰다. 재조합 pGEX-4T-3을 갖고 있는 대장균 BL21(DE3)로부터 생산된 Glutathione-s 전이효소 (GST) 융합 단백질을 얻어서 그중 ACE저해 펩타이드를 Sephadex G-25 컬럼 크로마토그래피로 정제하였다. 정제된 ACE 저해 펩타이드는 타이로신-아스파틱엑시드-그리신-글리신-발린-패닐알라린-아르기닌-발린-타이로신-트레오닌의 서열을 가진 새로운 decapeptide이었고 ACE에 대하여 경쟁적으로 저해하였다. The angiotensin I-converting enzyme (ACE) inhibitor has anti-hypertensive effects and has long been used as prevention or remedy of hypertension. This study were carried out to produce and purify a new ACE inhibitor from recombinant E. coli and further elucidate its structure-function relationship. Recombinant pGEX-4T-3 containing ACE inhibitory peptide gene of Saccharomyces cerevisiae was transformed into E. coli BL21(DE3). Glutathione-S transferase (GST) fusion protein from E. coli BL21(DE3) harboring the recombinant pGEX-4T-3 was obtained and the ACE inhibitory peptide was purified with Sephadex G-25 column chromatography. The purified ACE inhibitory peptide was a novel decapeptide with sequence Tyr-Asp-Gly-Gly-Val-Phe -Arg-Val-Tyr-Thr which shows very low similarity to the other ACE inhibitory peptide sequence. The purified ACE inhibitor competitively inhibited ACE.

생물학적 유동층의 Media 충진량에 따른 미생물 농도 변화

김환기,최두형,박찬수 全北大學校 附設 都市및環境硏究所 1998 都市 및 環境硏究 Vol.13 No.1

The variation of microbiological concentration with packed volume of media was examined in the biological fludized bed which has swirl flow. The TOC and HRT of synthetic wastewater was kept with 70 ㎎/ℓ and 1.6 hr in the reactor, respectively. The mean grain size of sand as media was 0.397 mm and its volume was packed from 20 % to 60 % in the reactor. The experiment results from the above conditions were the treatment efficiency of 87.5 to 93.7 %, the MLVSS of 2,360 to 3,860 ㎎/ℓ, and the microbiological concentration per g-media of 8.4 to 17.3 ㎎/ℓ. The detailed results are as follows. 1) The continuous operation was possible in the biological fludized bed which has swirl flow, not existing fludized bed. 2) The whole microbiological concentration in the reactor was the highest at packing the media volume of 40 to 45 % and the microbiological concentration per g-media was the highest at packing the media volume of 25 %. In the viewpoint of SS, the best packing volume of media was 35 to 45 % in that the separation of microbes were the lowest. 3) From SEM photographs, it showed as that cocci and bacillus adhere to and grow on the media surface

비모형화특성이 존재하는 연속시간 적응제어 알고리즘의 강인성 향상에 관한연구

김남준,이형찬 대진대학교 1994 大眞論叢 Vol.2 No.-

In this paper, a new robust diret adaptive controller using a modified adaptive law is suggested, in the presence of unmodeled dynamics and bounded disturbance in a linear time-invariant continuous system. The proposed algorithm consists of a conventional control law and the revised adaptive law to compensate for the drawback of o-modification algorithm. The proposed algorithm is applied to a plant with unmodeled dynamics represented as a singular perturbation. Boundness of all signals in overall system is guaranteed with mathematical analysis. Computer simulations show robustness of the proposed algorithm even in the presence of unmodelled dynamics or bounded disturbance simulatneously

배열형 전력 MOSFET의 설계 및 제작

김진형,최연익,정상구,박찬광,김충기,성만영 亞洲大學校 1987 論文集 Vol.10 No.-

In this paper, the design of the array type power MOSFETs is discussed in terms of on-resistance, breakdown voltage, placement of FLRs(field limiting ring) and threshold voltage. Also, 9-cell(square-on square grid) VDMOSs are fabricated to confirm the feasibility of the design method. Existence of optimum p-well spacing for minimum on-resistance, which is anticipated by the theoretical results is confirmed by the experiment of the fabricated power MOSFETs. Breakdown voltage of power MOSFET is upgraded by using two FLR's and their optimum placement is determined from the experimental results of the diodes with FLRs. The threshold voltage is controlled by the ion implantation within the design specification. Experimental results are in good agreement with the design specification. Experimental results are in good agreement with the design values. Characteristics of the fabricated power MOSFETs are 190Ω in on-resistance, 270V in breakdown voltage and 2.9V in thershold voltage.

Compocasting 법에 의한 AZ91D/SiC_pMMCs(metal matrix composites)제조

이경태,김세광,구형찬,김달식,김영직 成均館大學校 科學技術硏究所 1994 論文集 Vol.45 No.2

Metal matrix composites have toughness, machinability and heat conductivity, which can be obtained in metals, as well as hardness, high temperature stability, which can be obtained in ceramics. The purpose of this study is to find the optimum production condition of a compocasting method which is composed of stirring SiC particles inside a matrix which is presented as a solid or liquid state. During the compocasting method. SiC particles are mechanically incorporated into the matrix. From this study, sound AZ91D/SiC_p composites were obtained when stirring the matrix for 60minutes between 583-588℃.

광조형 시스템의 정밀조형을 위한 지지대 자동 생성 시스템 개발

강혁준,이형국,김효찬 동의공업대학 2000 論文集 Vol.26 No.1

Support structures are used to support a component during building process and must be removed once the building is complete. For precise building this paper specified types of support structures by means of geometry characteristics. They are point, line and area. And found a new algorithm for detecting geometries which need support structures. For easy of removing support structure teeth profile generation and interferences avoidance algorithm was studied.

실리카 입자를 함유한 광경화형 도료 물성

홍진후,주형태,김순기,김석찬 조선대학교 생산기술연구소 2004 生産技術硏究 Vol.26 No.1

We investigated the effects of nano-silica on the kinetic and film properties of UV curable coatings. Coating properties such as hardness, gloss, chemical and stain resistances and adhesion of the UV cured films containing various concentration of nano-silica were investigated. The matting, pencil hardness, chemical resistance, and abrasion resistances were apparently improved Via addition of nano-silica. Pendulum hardness was also enhanced with the increasing content of nano-silica up to 5 weight percent. However, the pendulum hardness and the adhesion decreased as nano-silica content increased above 10 weight percent. DPC analysis revealed that the presence of nano-silica in UV curable coating formulation enhanced photo curing. It was demonstrated that hardness. abrasion resistance, and chemical resistance of UV cured film can be increased without loss of optical properties through nanocomposite.