http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
윤영섭,윤덕용 대한금속재료학회(대한금속학회) 1977 대한금속·재료학회지 Vol.15 No.2
The effect of cold working and subsequent annealing on mechanical properties of W-Ni-Fe heavy alloy has been studied. The specimen composition was 90W-5Ni-5Fe by weight percent. The specimens were prepared by usual powder metallurgy techniques and sintered in liquid phase at 1460℃ for 30 minutes in hydrogen atmosphere. The specimens were then cold worked up to 60% by rolling. The observed UTS increases with cold working from about 94㎏/㎟ to 143㎏/㎟ at 50% deformation. The elongation decreases sharply from 20% to about 2% at 15% deformation. While the microhardness of the tungsten grains increases steadily with degree of cold work, the micro hardness of the matrix appears to increase rapidly with deformation initially. It is therefore suggested that at relatively small deformation the matrix phase work hardens rapidly and affects the deformation behavior of the composite alloy. The alloy specimen cold worked to 50% was annealed at temperatures from 400℃ to 1000℃ for an hour in hydrogen atmosphere and the mechanical properties were measured. Annealing of the cold worked specimen at 400˚increases UTS to 160㎏/㎟ from 143㎏/㎟ for the unannealed specimen, and with increasing annealing temperatures UTS decreases. The elongation begins to increase with annealing temperature at 800℃ and rises sharply to 4% at 1000℃. The microhardness of the tungsten grains remains unchanged with annealing temperature up to 600℃ and from 800℃ begins to decrease slowly. The microhardness of the matrix on the other hand shows maximum after annealing at 400℃ and decreases subsequently with higher annealing temperatures. These observations indicate that the increase of the UTS after annealing at 400℃ is largely due to the increased strength of the matrix. This increase in matrix strength with annealing is most likely caused by some, kind of precipitation hardening which is probably accelerated by cold work. The observed changes of mechanical properties at higher annealing temperatures are attributed mainly to the recovery and recrystallization of the matrix phase.
윤영섭,김정훈,박찬휘,신동욱 한양대학교 세라믹연구소 2013 Journal of Ceramic Processing Research Vol.14 No.4
Lithium ion conducting NASICON-type electrolytes of general formula Li1.3Al0.3Ti1.7(PO4)3 (LATP) are fabricated by a citric acid-supported sol-gel process and analyzed for thermal stability, microstructure, crystalline phases. From these structural analyses, the relationship of microstructural changes and electrochemical properties is investigated. It is demonstrated that the sol-gel method enable to obtain pure LATP crystals at a lower temperature in a shorter synthesis time compared to conventional solid state reaction or glass-ceramics processes. The dense electrolyte pellets are prepared from the LATP nanopowders by sintering at 900 o C for 3 hours, and a room temperature conductivity of 7.8 × 10-5S/cm and activation energy of 38.2 KJ/mol was obtained.
Do Focused Funds Create Superior Performance? - The Evidence From the Korean Fund Market
윤영섭,김성신,손판도 한국재무학회 2008 한국재무학회 학술대회 Vol.2008 No.05
한국의 펀드산업은 과거 수년간 양적 질적으로 괄목할만한 성장을 거두어왔으나 펀드의 운용성과에 관한 분석은 매우 미흡한 실정이다. 펀드운용의 기본이 분산투자라 하는 것은 주지하는 바와 같다. 그러나 과거 수년 동안 수행된 몇 논문들은 우월한 정보를 가진 산 업에 속한 종목에 집중된 투자를 하는 것이 분산된 투자보다 더 우수한 성과를 보인다는 사실을 이론적, 실증적으로 증명하고 있다. 이 논문의 목적은 2001-2007년에 걸친 한국 펀드자료를 가지고 이러한 집중된 투자가 과연 더 우수한 성과를 보이는가를 실증적으로 분석하는 것이다. 논문의 결과를 요약하면 대략 다음과 같다. 비조건부 및 조건부 모형을 각각 사용하여 펀드성과를 측정한 결과, 산업집중도가 높은 펀드가 산업집중도가 낮은 펀드에 비해 월 0.4%와 0.2% 정도의 초과이익을 보이는 것으로 나타났다. 이러한 차이는 통계적으로 유 의할 뿐만 아니라 펀드 특성 변수를 통제한 후에도 비슷하게 나타났다. 또한, 펀드운용자 가 우월한 정보를 이용하여 미래 성과가 좋은 특정 산업을 선택할 수 있으며 특정 산업 내에서 좋은 주식을 선택할 수 있는 능력을 가졌는가의 여부를 검정하였는데 집중된 펀드 에서 그러한 사실을 발견할 수 있었다. 또한, 펀드규모에 따라 성과가 달라지는가를 검정 한 결과 집중된 펀드의 성과가 펀드 규모에 영향을 받지 않음을 보였다. 따라서 이 연구 는 우리나라에서도 펀드운용자가 정보우위를 가진 특정 산업에 집중적으로 투자할 경우 보다 우수한 운용성과를 투자자에게 가져다 줄 수 있음을 확인하였다.