고상법에 의한 100 nm BaTiO₃ 분말의 합성

김정환,정한승,조준엽,홍정오,김영태,허강헌,Kim, Jung-Hwan,Jung, Han-Seong,Cho, Joon-Yeob,Hong, Jeong-Oh,Kim, Young-Tae,Hur, Kang-Heon 한국세라믹학회 2009 한국세라믹학회지 Vol.46 No.2

$BaTiO_3$ powder was synthesized by the solid-state reaction of fine $BaTiO_3$ and $TiO_2$ raw materials. Fine grinding media of 50 and 300 microns were used for obtaining fine particulate mixture of $BaTiO_3$ and $TiO_2$ with high homogeneity. Effect of the size of grinding media on the synthesis mechanism of $BaTiO_3$ was discussed on the basis of the particulate morphology and thermogravimetry data for the mixture powders. By using the finer grinding media, $BaTiO_3$ was formed at the lower temperature and the particle size with the relatively narrower distribution could be obtained. $BaTiO_3$ powder with the average size of 100 nm was synthesized by the solid reaction in vacuum atmosphere.

PLD를 이용한 강유전체(PZT, PST, PT)/YBCO 박막 구조의 제작과 전기적인 특성에 관한 연구

김정환,이재형,문병무,Kim, Jung-Hwan,Lee, Jae-Hyung,Moon, Byung-Moo 한국전기전자재료학회 1998 전기전자재료학회논문지 Vol.11 No.7

(PZT, PST, PT)/ YBCO structured have been grown on single crystal $LaAlO_3$ using in-situ Nb:YAG pulsed laser deposition technique. The optimum conditions of fabrication for high quality films have been established under various oxygen pressure. TBCO was used as a metallic electrode for polarizing ferroelectric thin fillms. Lattice mismatch of these materials were found to be with in 3%. As a result XRD patterns and rocking curves, (PZT, PST, PT)/ YBCO multiayered thin films on $LaAlO_3$ substrates showed preferred orientation to c-axis. For invastigation on electrical properties of ferroelectric thin films, remanent polaiztion $P_r$ and coercive field $E_c$ were measured for three samples. At each optimum condition, they showed the values of P_r=60 \mu C/cm^2 and E_c=240kV/ cm for PT, 30\mu C/cm^2 and 105kV/cm for PZT, 1.5\mu C/cm^2$ and 15kV/cm for PST. Frequency dependence of dielectric properties of ferroelectric thin fillms was also investigated. As a result, it showed the frequency dependence was relatively small in the range of 10Hz~10kHz.

산 완충능력과 토양 성분이 동전기-펜톤 공정에 의한 phenanthrene 오염토양 정화에 미치는 영향

김정환,나소정,박주양,변영덕,Kim, Jung Hwan,Na, So Jeong,Park, Joo Yang,Byun, Young Deog 한국지하수토양환경학회 2013 지하수토양환경 Vol.18 No.1

This research was conducted to investigate effects of acid buffering capacity and soil component in treatment of phenanthrene using electrokinetic-Fenton process. In Hadong clay of high acid buffering and low iron oxide content, it was difficult to oxidize phenanthrene due to shortage of iron catalyst and scavenger effect of carbonate minerals. The desorbed phenanthrene conductive to Fenton oxidation was transported toward cathode by electroosmotic flow. However, in Youngdong illitic clay, oxidation of phenanthrene near anode readily occurred compared to Hadong clay due to high iron content and low acid buffering capacity.

The Binarization of Text Regions in Natural Scene Images, based on Stroke Width Estimation

김정환,이귀상,Zhang, Chengdong,Kim, Jung Hwan,Lee, Guee Sang 한국스마트미디어학회 2012 스마트미디어저널 Vol.1 No.4

In this paper, a novel text binarization is presented that can deal with some complex conditions, such as shadows, non-uniform illumination due to highlight or object projection, and messy backgrounds. To locate the target text region, a focus line is assumed to pass through a text region. Next, connected component analysis and stroke width estimation based on location information of the focus line is used to locate the bounding box of the text region, and each box of connected components. A series of classifications are applied to identify whether each CC(Connected component) is text or non-text. Also, a modified K-means clustering method based on an HCL color space is applied to reduce the color dimension. A text binarization procedure based on location of text component and seed color pixel is then used to generate the final result.

원형 쉬프트 통신의 중첩 효과 분석

김정환,노정규,송하윤,Kim, Jung-Hwan,Rho, Jung-Kyu,Song, Ha-Yoon 한국정보처리학회 2002 정보처리학회논문지 A Vol.9 No.2

통신과 계산 작업을 중첩 수행함으로써 통신 시간의 감춤 효과를 얻는 것은 일반적인 병렬 프로그램 최적화 방법 중의 하나이다. 본 논문에서는 데이타 병렬 프로그램에서 자주 사용되는 군집 통신(collective communication)의 하나인 원형 쉬프트(circular shift) 통신에 대해 중첩 효과를 실험하고 고찰하였다. 이더넷 스위치로 연결된 클러스터 시스템에서 원형 쉬프트 통신을 수행할 때, 중첩으로 얻을 수 있는 최대 이득과 중첩할 수 없는 시간을 측정하였다. 각 플랫폼 별로 이러한 측정값들을 얻어 퇴적화 컴파일러의 입력으로 활용할 수 있을 것이다. 한편 기존의 성능 모델을 통해 퇴적화하는 것은 크게 두가지 문제를 갖고 있다. 하나는 기본적인 점대점 통신에 입각한 모델을 제공하기 때문에 통신 라이브러리의 함수를 사용할 때의 종합적인 효과, 특히, 군집 통신과 같은 경우에는 적용하기 어렵다는 것이다. 다른 하나는 군집 통신의 성능은 분석은 가능하지만, 중첩 효과는 분석할 수 없다는 것이다. 본 논문에서는 이러한 기존 모델의 단점을 보완하여 확장하였다. 또한, 원형 쉬프트 통신에 대한 실험 결과를 토대로 확장된 모델의 매개 변수 값들을 추출하여 예제 프로그램을 통해 분석하였다. Many researchers have been interested in the optimization of parallel programs through the latency hiding by overlapping the communication with the computation. We ana1yzed overlapping effects in the circular shift communication which is one of the collective communications being frequently used In many data parallel programs. We measured the time which can be possibly overlapped and the time which cannot be overlapped in over all circular shift communication period on an Ethernet switch-based clustered system. The result from each platform nay be used for the input of optimizing compilers. The previous performance models usually have two kinds of drawbacks one is only based on point-to-point communication, so it is not appropriate for analyzing the overall effects of collective communications. The other provides the performance of collective communication, but no overlapping effect. In this paper we extended the previous models and analyzed the experimental results of the extended model.

새로운 2-(4-phenyl)Quinazolylacetonitrile 유도체들의 합성

김정환,남상욱,Jung-Hwan Kim,Sang-Uook Nam 대한화학회 2003 대한화학회지 Vol.47 No.4

R&D와 규모의 영세성이 산업별 총요소생산성에 미치는 영향

김정환,이동기,이부형,주원,Kim, Jung-Hwan,Lee, Dong-Ki,Lee, Bu-Hyung,Joo, Won 한국벤처창업학회 2007 벤처창업연구 Vol.2 No.4

There were many comprehensive analyses conducted within the existing research activities wherein factors affecting technology progress including investment in R&D vis-${\Box}$-vis their influences act as the determinants of TFP. Note, however, that there were few comprehensive analysis in the industrial research performed regarding the impact of the economy of scale as it affects TFP; most of these research studies dealt with the analysis of the non -parametric Malmquist productivity index or used the stochastic frontier production function models. No comprehensive analysis on the impacts of individual independent variables affecting TFP was performed. Therefore, this study obtained the TFP increase rate of each industry by analyzing the factors of the existing growth accounting equation and comprehensively analyzed the TFP determinants by constructing a comprehensive analysis model considering the investment in R&D and economy of scale (smallness by industry) as the influencers of TFP by industry. First, for the TFP increase rate of the 15 industries as a whole, the annual average increase rate for 1993${\sim}$ 1997 was approximately 3.8% only; during 1999${\sim}$ 2000 following the foreign exchange crisis, however, the annual increase rate rose to approximately 7.8%. By industry, the annual average increase rate of TFP between 1993 and 2000 stood at 11.6%, the highest in the electrical and electronic equipment manufacturing business and IT manufacturing sector. In contrast, a -0.4% increase rate was recorded in the furniture and other product manufacturing sectors. In the case of the service industry, the TFP increase rate was 7.3% in the transportation, warehousing, and communication sectors. This is much higher than the 2.9% posted in the electricity, water, and gas sectors and -3.7% recorded in the wholesale, food, and hotel businesses. The results of the comprehensive analysis conducted on the determinants of TFP showed that the correlations between R&D and TFP in general were positive (+) correlations whose significance has yet to be validated; in the model where the self-employed and unpaid family workers were used as proxy variables indicating the smallness of industry out of the total number of workers, however, significant negative (-) correlations were noted. On the other hand, the estimation factors of variables surrogating the smallness of scale in each industry showed that a consistently high "smallness of scale" in an industry means a decrease in the increase rate of TFP in the same industry.

50μm급 이트리아 안정화 지르코니아 비드의 미세구조 및 마모 조건에 따른 마모율 분석

김정환,윤세중,한병동,안철우,윤운하,최종진,Kim, Jung-Hwan,Yoon, Sae-Jung,Hahn, Byung-Dong,Ahn, Cheol-Woo,Yoon, Woon-Ha,Choi, Jong-Jin 한국재료학회 2019 한국재료학회지 Vol.29 No.4

This study analyzes the mechanical properties, including the attrition rate, of $50{\mu}m$ size yttria-stabilized zirconia (YSZ) beads with different microstructures and high-energy milling conditions. The yttria distribution in the grain and grain-boundary of the fully sintered beads relates closely to Vickers hardness and the attrition rate of the YSZ beads. Grain size, fractured surfaces, and yttrium distribution are analyzed by electronic microscopes. For standardization and a reliable comparison of the attrition rate of zirconia beads with different conditions, Zr content in milled ceramic powder is analyzed and calculated by X-ray Fluorescence Spectrometer(XRF) instead of directly measuring the weight change of milled YSZ beads. The beads with small grain sizes sintered at lower temperature exhibit a higher Vickers hardness and lower attrition rate. The attrition rate of $50{\mu}m$ YSZ beads is measured and compared with the various materials properties of ceramic powders used for high-energy milling. The attrition rate of beads appears to be closely related to the Vickers hardness of ceramic materials used for milling, and demonstrates more than a 10 times higher attrition rate with Alumina(Hv ~1650) powder than $BaTiO_3$ powder (Hv ~315).

한글 문자 입력 인터페이스 개발을 위한 눈-손 Coordination에 대한 연구

김정환,홍승권,명노해,Kim, Jung-Hwan,Hong, Seung-Kweon,Myung, Ro-Hae 대한인간공학회 2007 大韓人間工學會誌 Vol.26 No.2

Recently, various devices requiring text input such as mobile phone IPTV, PDA and UMPC are emerging. The frequency of text entry for them is also increasing. This study was focused on the evaluation of Korean text entry interface. Various models to evaluate text entry interfaces have been proposed. Most of models were based on human cognitive process for text input. The cognitive process was divided into two components; visual scanning process and finger movement process. The time spent for visual scanning process was modeled as Hick-Hyman law, while the time for finger movement was determined as Fitts' law. There are three questions on the model-based evaluation of text entry interface. Firstly, are human cognitive processes (visual scanning and finger movement) during the entry of text sequentially occurring as the models. Secondly, is it possible to predict real text input time by previous models. Thirdly, does the human cognitive process for text input vary according to users' text entry speed. There was time gap between the real measured text input time and predicted time. The time gap was larger in the case of participants with high speed to enter text. The reason was found out investigating Eye-Hand Coordination during text input process. Differently from an assumption that visual scan on the keyboard is followed by a finger movement, the experienced group performed both visual scanning and finger movement simultaneously. Arrival Lead Time was investigated to measure the extent of time overlapping between two processes. 'Arrival Lead Time' is the interval between the eye fixation on the target button and the button click. In addition to the arrival lead time, it was revealed that the experienced group uses the less number of fixations during text entry than the novice group. This result will contribute to the improvement of evaluation model for text entry interface.

노인 복지를 위한 응급 상황 호출 프로그램의 개발 및 구현

김정환,조면균,김식,Kim, Jung-Hwan,Cho, Myeon-Gyun,Kim, Shik 대한임베디드공학회 2013 대한임베디드공학회논문지 Vol.8 No.2

This paper proposes a system that utilizes USN(Ubiquitous Sensor Network), Bluetooth and smart phone to improve the function of senior houses. In typical approach, a system in a senior house either directly accesses the status of elderly people by its sensor or is alerted by elderly people who trigger an emergency bell, derive a decision and take an appropriate action. In addition, it is possible for a designated social worker to check the status of senior patients through monitoring system connected by UTP(Unshielded Uwisted Pair) cables, but the responsible person has to be present to monitor patients' status. However, the new system, suggested in this paper, embed Bluetooth function in a blood pressure gauge, thus the smart phone receives patients' health information such as blood pressure through Bluebooth, if any abnormal event occurs. Consequently, the smart phone sends SMS(Short Message Service) to a responsible social worker or a designated hospital. When this program in the paper becomes a reality, an unmanned system that is able to determine suitable actions for certain events will be established, even if a social worker were absence.