치과 임플란트용 골융합 측정기의 설계 및 평가

이주희,김창일,백종후,조정호,전명표,정영훈,이영진,이정배,이승대,Lee, Joo-Hee,Kim, Chang-Il,Paik, Jong-Hoo,Cho, Jeong-Ho,Chun, Myoung-Pyo,Jeong, Young-Hun,Lee, Young-Jin,Lee, Jeong-Bae,Lee, Seung-Dae 한국전기전자재료학회 2011 전기전자재료학회논문지 Vol.24 No.3

The osseointegration of dental implant is influenced by many factors such as surface geometry, loading and the amount of bone. Thus, stability of the dental implant should be checked periodically. In order to test the stability of dental implant by using resonance frequency analysis, we designed a structure of transducers and fabricated a piezoelectric devices. Using finite element analysis, the thickness and length of piezoelectric device and transducers were tailorized and the optimized frequency of 10 kHz was obtained. The resonance frequency from simulation analysis and evaluation was estimated to be similar as 10 kHz. The osseointegration was further enhanced with increasing frequency from the evaluation result of the finite element analysis.

치과용 초음파 골수술기 설계 및 평가

이주희,오정민,홍연우,김세기,백종후,이영진,이정배,이승대,Lee, Joo-Hee,Oh, Jung-Min,Hong, Younwoo,Kim, Seiki,Paik, Jonghoo,Lee, Young-Jin,Lee, Jeong-Bae,Lee, Seung-Dae 한국전기전자재료학회 2012 전기전자재료학회논문지 Vol.25 No.12

A piezoelectric ultrasonic bone surgical instrument, usually used to remove the tartar out of teeth or to cut the dentine of the tooth, is a recently popular instrument for dental treatment due to its several merits such as small size, low-electric power and precision control of surgical operation. It has typically two parts of a tip and vibration system which is also composed of head, piezoelectric elements and tail-mass. In order to improve the performance of the instrument, it is important to standardize the size of the vibration system without tip for high performance. In this study, a Finite Element Analysis (FEA) was utilized to optimize the structure of ultrasonic instrument in vibration system. Consequently, this study revealed that influence of several tips on property were minimized and it showed good property at the frequency range of 22~32 kHz.

델파이 분석을 통한 조경설계공모 과정의 문제점 분석

이주희,조세환,Lee, Joo-Hee,Cho, Se-Hwan 한국조경학회 2013 韓國造景學會誌 Vol.41 No.3

본 연구는 1983년 설계공모 제도가 한국 조경계에 도입되고 30년이 지난 현 시점에서 조경 설계공모 과정에서 발생되고 있는 문제점을 분석 고찰함으로써 향후 조경 설계공모 과정 개선에 기여할 수 있는 기초자료를 제공하기 위한 목적으로 수행하였다. 연구를 수행하기 위해 조경 설계공모에 관여하는 전문가를 대상으로 델파이 조사를 실시하여 문제점을 도출하였으며, 그 결과는 다음과 같다. 첫째, 조경설계 공모 관련 이론과 선행연구를 분석한 결과, '설계공모 방식', '설계공모 지침', '당선작 선정과정', '당선작 이후 설계변화' 등 4가지 관점에서 문제점이 있는 것으로 나타났다. 둘째, 전문가 델파이 분석을 통하여 전문가들의 의견을 합의하는 과정을 이끌었고, 그 결과 총 12개의 항목으로 조경설계 공모 과정의 문제점이 도출되었는바, '설계공모 방식'에서는 '설계공모 기간의 문제', '설계공모 방식' 등 2가지의 항목, '설계공모 지침'에서는 '비위계적이고 혼란스러운 지침', '규정적으로 정해지는 지침', '지침의 분량의 과다' 등 3개 항목, '당선작 선정과정'에서는 '심사위원 전문성 결여', '비조경전문가 참여', '심사배점 방식에 문제점' 등 3개 항목, '당선작 이후 설계변화'에서는 '발주처 설계담당자의 잦은 인사이동', '설계기간의 기약 없는 과다연장', '발주처의견이 과다하게 반영되는 풍토', '원설계의 창의성을 저감시키는 발주처 의견' 등 4가지 항목이 문제점으로 나타났다. This study has been performed to analyze and consider the problems after 30 years in terms of landscape design competition process in Korea, so that it can provide the basic data, which can improve the future landscape design competition. We have used Delphi Investigation to carry out a survey that targets professionals and identifies problems. The results are summarized as follows. Firstly, the results of the analysis of Landscape Design Competition for institution theory and case studies showed that there is an issue from four perspectives which are 'method of design competition', 'guidelines for design competition', 'winner selection process', and 'design changes after winning' Secondly, the process by professional Delphi performed expert analysis, and agree with expert opinion. As a result, we derived the problems of a landscape design competition system with the 12 items. Third, in the 'design competition style', two items, the 'design competition style' and 'problem of design public offering period' had become a problem. Fourth, the 'Guidelines for design competition', 'non-hierarchical excess of the amount of instructions', 'directive determined the guidelines', and the 'provision of confusion' three items had also become a problem. Fifth, 'sex expert committee review selection process winning work', 'Problems of participation', 'examination scoring system experts lack', and 'non-landscaping' had become a problem. Sixth, 'The design of the original order' as much as possible 'design changes after the winning work' Four 'order to Comments to reduce the creativity of the design of the climate', 'original extension', 'contractor feedback of excess without the promise of frequent personnel changes', design period of the person in charge is reflected in excess item has become a problem. I considered that a continuous research on the improvement of the problems of the landscape design competition system based on the results must be performed.

Removal torque of a two-piece zirconia abutment with a novel titanium component in an internal connection implant system after dynamic cyclic loading

이주희,Lee, Joo-Hee The Korean Academy of Prosthodonitics 2017 대한치과보철학회지 Vol.55 No.2

목적: 이 연구의 목적은 새로운 타이타늄 구성요소를 가진 지르코니아 지대주의 나사 제거력의 변화에 대해 알아보는 것이다. 내부연결 임플란트를 위한 새로운 지르코니아 지대주의 동적하중 후 지대주 나사의 제거력을 기존의 타이타늄 지대주와 비교하여 분석하였다. 재료 및 방법: 내측연결 임플란트와 타이타늄 지대주, 타이타늄 구성요소를 가진 지르코니아 지대주를 준비하였다. 12개의 내부연결형 임플란트에 6개의 타이타늄 지대주를 연결하고(대조군), 6개의 타이타늄 구성요소를 가진 지르코니아 지대주(실험군)를 30 Ncm의 토크로 연결한 후 동적하중 전후의 나사 제거력을 측정하였다. 동적 만능재료시험기를 사용하여 연결체의 장축과 30도 각도를 이루도록 하고 300 N 하중크기로 100만번의 하중이 가해졌다. 동적하중 전후의 지대주 나사 제거력을 t검정을 통해 신뢰구간 95%로 통계적 유의성을 검증하였다. 결과: 두 그룹 모두에서 동적하중 후 나사 풀림을 보이지 않았다. 동적 하중 전후의 나사 제거력은 두 그룹 모두에서 통계적으로 유의한 차이가 있게 나타났다(P < .05). 동적 하중 전후의 나사 제거력 차이는 대조군에서 $-7.25{\pm}1.50Ncm$, 실험군에서 $-7.33{\pm}0.93Ncm$ 로 나타났다. 통계분석 결과 두 군간에 나사 제거력 차이에서는 유의한 차이를 보이지 않았다(P > .05). 결론: 이 실험의 결과에 한하여 타이타늄 구성요소를 사용한 지르코니아 지대주의 동적하중 후 지대주 나사 제거력의 변화는 타이타늄 지대주와 통계학적으로 유의한 차이를 보이지 않았다. Purpose: The aim of this study was to evaluate screw removal torque of the two-piece zirconia abutment with the novel titanium component compared to the conventional one-piece titanium abutment in the internal connection implant before and after dynamic cyclic loading. Materials and methods: Two types of the abutment assemblies with internal connection were prepared and divided into the groups; titanium abutment-titanium abutment screw assemblies as control, and zirconia abutment-titanium socket-titanium abutment screw assemblies as experimental group. A total of 12 abutments and implants were used of six assemblies each group. Each assembly was tightened to 30 Ncm. A cyclic load of 300 N at an angle of 30 degrees in reference to the loading axis was applied until one million cycles or failure. The removal torque values (RTVs) of the abutment screws were measured with a digital torque gauge before and after cyclic loading. The RTVs of the pre load and post load were analyzed with t-test, and P-values < .05 were considered statistically significant. Results: The assemblies of both groups survived all after the dynamic cyclic loading test without screw loosening. The statistically significant differences were found between the mean RTVs before and after the cyclic loading in both groups (P < .05). The RTV differences for the control and the experimental group were $-7.25{\pm}1.50Ncm$ and $-7.33{\pm}0.93Ncm$, respectively. Statistical analysis revealed that the RTV differences in both groups were not significantly different from each other (P > .05). Conclusion: Within the limitation of this study, the two-piece zirconia abutment with the titanium component did not show a significant RTV difference of the abutment screw compared to the titanium abutment after dynamic cyclic loading.

임플랜트 상부 보철물의 고정 방식에 따른 힘의 분포에 관한 연구 : 나사 유지형 대 시멘트 유지형

이주희,김창회,김영수,Lee Joo-Hee,Kim Chang-Whe,Kim Yung-Soo 대한치과보철학회 2001 대한치과보철학회지 Vol.39 No.2

To compare the stress distribution patterns between cement-retained and screw-retained implant supported fixed prostheses according to four different abutment types, a three dimensional finite element analysis was performed. The hypothetical three unit fixed partial denture case was modelled on the three implants(10mm length and 3.75 diameter) in mandibular bone. Four angles of implantation(vertical, 10, 15 and 20 degree inclined mesially) were created and three different directions of force (vertical, oblique, horizontal) were applied at the center of the second premolar and distal end of the first molar for each cases. Within the limits of this study, the results were as follows, 1. In vertically installed cases, the more stress was concentrated at upper components, but mesially inclined cases, the more stress was concentrated at cortical bone. 2, The more inclined mesially the more stress was observed, especially at cortical bone. 3. The cement-retained models showed lower principal stress and more even stress distribution than the screw-retained models. 4. The similar stress distribution pattern was showed in model 1 and model 2, model 3 and model 4. 5. The more stress was observed when the loads were applied at the distal end of 1st molar than the center of 2nd premolar. 6 The fixture and the model as a whole, lesser stress values were observed when vertical loads were applied as compared to horizontal and oblique loads.

표면 처리법에 따른 치과용 합금과 열중합형 레진 간의 결합 강도에 관한 연구

이주희,정은민,장복숙,정동준,허성주,한동후,심준성,Lee Joo-Hee,Jung Eun-Min,Jang Bok-Sook,Chung Dong-June,Heo Seong-Joo,Han Dong-Hoo,Shim June-Sung 대한치과보철학회 2002 대한치과보철학회지 Vol.40 No.4

The purpose of this study is to compare tensile bond strength between Cr-Co alloy and three denture base resins after surface treatment. Following the manufacturer's instructions, 180 bonded specimens were made from three denture base resins (Lucitone 199. Paladent 20. POSS resin) and three surface treatment methods (sandblasting. metal primer. silicoating) 20 samples were made in each group and a half was ther-mocycled 1000 times between $5^{\circ}C$ and $55^{\circ}C$. The tensile bond strength was measured using an Instron with 5mm/min crosshead speed. Data was analyzed with one-way ANOVA, T-test and Duncan test. The results were as follows : 1. Samples with metal primer coating had significantly high tensile bond strength than the other surface treated groups (p<.05). Significantly low tensile bond strength was shown in sand blasted groups (p<.05). 2. No significant difference was observed in metal primer coating groups before and after ther-mocycling (p>.05) 3. Tensile bond strength was decreased in silicoated samples after thermocycling (p<.05). 4. Of the surface treated groups with metal primer, Lucitone 199 had the greatest bond strength and POSS resin and Paladent 20 were followed (p<.05). 5. Of the surface treated groups with silicoating, POSS resin and Lucitone 199 had greater bond strength than Paladent 20 (p<.05).

아파트 보조부엌의 유형별 개조특성에 관한 연구

이주희,오찬옥,양세화,Lee, Joo-Hee,Oh, Chan-Ohk,Yang, Se-Hwa 한국주거학회 2007 한국주거학회 논문집 Vol.18 No.2

The study analyzes the remodeling characteristics of the four different types of secondary kitchens in apartment house based on their floor plans. The secondary kitchens are categorized into side placement, back placement, back placement with extensions on both sides, and back placement with an extension on a single side. The twelve apartment complexes in Ulsan were selected so that they may all consist each of the four types, and answered the survey. The classified traits of secondary kitchen were examined based on the characteristics of floor plan and remodeling. Side placement and back placement with extensions on both sides mostly used glass hinged doors. Back placement and back placement with a single side extension used glass sliding doors. It was found that the majority of the floor materials consisted of both wood and tiles, except for side placements, where only tiles were used. The sizes of the back placements with both and single side extensions were the largest. The side and back placements were rarely renovated, however, back placements with both and single side extensions went through massive remodeling.

의치용 인공치아와 의치상용 레진간의 결합강도에 관한 실험적 연구

이주희,김창회,김영수,Lee, Joo-Hee,Kim, Chang-Whe,Kim, Yung-Soo 대한치과보철학회 1996 대한치과보철학회지 Vol.34 No.3

A principal advantage of a plastic tooth over a porcelain tooth should be its ability to bond to the denture base material. But plastic teeth could craze and wear easily, so more abrasion resistant plastic denture teeth have been developed. To resist abrasion, the degree of cross-linking was increased, but bonding to denture base meterial became more difficult. The purpose of this study was to evaluate the bond strength of plastic teeth and abrasion resistant teeth bonded to heat-curing, self-curing and light-curing denture base material. Denture tooth molds were chosen that had a>8mm diameter. The denture teeth was bonded to three denture base materials and then machined to the same dimensions. Three denture base materials were used as control groups. Prior to tensile testing, the specimens were thermocycled between $5^{\circ}C\;and\;55^{\circ}C$ for 1000cycles. Tensile testing was performed on an Instron Universal testing mechine. Experimental group ; plastic teeth(Justi Imperial)+heat-curing resin(Lucitone 199) plastic teeth(Justi Imperial)+light-curing resin(Triad) plastic teeth(Justi Imperial)+self-curing resin(Vertex SC) abrasion resistant teeth(IPN)+heat-curing resin(Lucitone 199) abrasion resistant teeth(IPN)+light-curing resin(Triad) abrasion resistant teeth(IPN)+self-curing resin(Vertex SC) Control group ; heat-curing resin(Lucitone 199) light-curing resin (Triad) self-curing resin(Vertex SC). The results were as follows : 1. The denture teeth bonded to heat-curing resin showed the cohesive failure and those bonded to the other resins showed adhesive failure. 2. Tensile bond strength of the plastic teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 3. Tensile bond strength of the abrasion resistant teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 4. Tensile bond strength of the plastic teeth to self-curing resin was not significantly different from that of the abrasion-resistant teeth(p>0.05). 5. Tensile bond strength of the plastic teeth to light-curing resin was significantly greater than that of the abrasion resistant teeth(p<0.01).

통영지역 해녀의 식습관 및 영양소섭취 실태조사

이주희,김찬,Lee, Joo-Hee,Kim, Chan 대한지역사회영양학회 2002 대한지역사회영양학회지 Vol.7 No.6

The purpose of this study was to investigate the nutritional intake and dietary habits of women divers in Tongyoung area and to support the guideline for the improvement of their dietary life style by a validation of a Computerized Semi-quantitative Food Frequency Questionaire. Compared to the women at Jeju Island, the Tongyoung divers showed similar heights (154.6 $\pm$ 0.8 cm), weights (53.5 $\pm$ 1.0 kg) and BMIs (23.3 $\pm$0.4) , but they showed especially high levels of body fat (33.8 $\pm$ 0.8) . Their dietary habits showed they usually skipped lunch, but ate too much food at once, which may represent the dietary habits shown by obese people. Over 40% of the divers were taking some nutritious food or complementary food for health, without realizing the efficacy of these foods. The analysis of nutritional intake showed that all of average daily nutrients intakes of those below 50 years were higher than those of the Korean RDA. In the case of those above 50 years, it was shown that the average daily nutrients intakes were also higher than those of the Korean RDA except for energy (94.5%) and calcium (82.1%) . However, some individual divers showed lower nutrients intakes than 75% of RDA for calcium, iron, Vitamin A and Vitamin B$_2$. Also, excessive intakes of phosphorous and sodium could be a dietary problem. There was no correlation between BMI or percentage of body fat and energy, CHO, protein or fat. These results can provide the nutritional information for this special community, women divers, to improve their health.

단체 급식 종사자와 일반주부와의 영양지식·위생지식 및 실행도 차이 비교연구

이주희,신지연,김창임,Lee, Joo Hee,Shin, Ji Yeon,Kim, Changim 한국식품영양학회 2014 韓國食品營養學會誌 Vol.27 No.6

This research is aimed at evaluating the nutrition knowledge and hygiene knowledge of people who are either foodservice employees or housewives and at providing data for conducting hygiene education by comparing the differences between the two groups. Both groups scored relatively high in nutrition knowledge with housewives scoring 9.9/12 and food service employees scoring 9.6/12. However, foodservice employees scored significantly higher in hygiene knowledge and degree of practice than housewives, A correlation was found between nutrition knowledge and the degree of hygienic practice and a significant correlation between hygiene knowledge and the degree of hygienic practice. The higher the hygiene knowledge was, the higher their degree of hygienic practice was. As for food hygiene information, foodservice employees obtained the information through hygiene education and lecture meetings, but housewives got their information through mass media. To summarize, mass media, which housewives can have easy access, must have programs for housewives to help them improve food hygiene in cooking, and programs for foodservice employees on washing food.