재생근관치료 결과에 영향을 미치는 인자의 분석

김인기,김현태,송지수,신터전,현홍근,김영재,김정욱,장기택,Kim, In-Ki,Kim, Hyuntae,Song, Ji-Soo,Shin, Teo Jeon,Hyun, Hong-Keun,Kim, Young-Jae,Kim, Jung-Wook,Jang, Ki-Taeg 대한소아치과학회 2021 大韓小兒齒科學會誌 Vol.48 No.4

This study retrospectively analyzed the effect of clinical factors on the outcomes of REP(regenerative endodontic procedure). Patients who received the REP using triple antibiotic paste due to trauma or fracture of dens evaginatus from February, 2011 to January, 2020 were included in the study. Finally, 57 teeth in 54 patients were selected. Investigated clinical factors were as follows: intentional bleeding, etiology, and root development stage. Treatment outcomes evaluated were as follows: improvement of subjective symptoms, changes in the periapical lesion, and the amounts of root development after REP. To compensate for differences in angulation and position between repeated radiographic examinations, images were aligned by Turboreg plugin. To evaluate the amounts of root development, apical diameter, root area, and root length were measured by ImageJ software. Among the aforementioned factors, intentional bleeding had no significant effect on treatment results. Regarding the etiology, the increase in the root area and the root length was significantly less in trauma cases than in dens evaginatus fracture cases. Considering root development stage, more immature teeth presented more increase in the root area. 이 연구는 재생근관치료 결과에 영향을 줄 것으로 예상되는 인자를 후향적으로 분석하였다. 2011년 2월부터 2020년 1월까지 외상과 치외치 파절로 항생제 복합제제를 사용하여 재생근관치료를 시행한 54명의 환자와 57개의 치아를 대상으로 하였다. 의도적 출혈 여부, 치료원인, 치근발육단계에 따른 재생근관치료 결과를 분석하였다. 치료 결과는 증상의 개선, 치근단병소의 변화, 치근성장량을 토대로 판단하였다. 영상 촬영각도 및 위치에 의한 왜곡을 보정하기 위해 Turboreg plugin을 사용하였고, ImageJ softeware상에서 치근단공 크기, 치근면적, 치근길이의 변화를 측정하였다. 의도적 출혈 유무는 치료 결과에 유의한 영향이 없었다. 외상으로 인한 경우 치외치 파절로 인한 경우보다 치근면적과 치근길이의 증가가 적었다. 치근발육이 덜 진행된 치아일수록 치근면적의 성장이 크게 나타났다.

기계적 합금법으로 제조한 Mg_3-xZn_xSb₂의 열전물성

김인기,장경욱,김일호,Kim, In-Ki,Jang, Kyung-Wook,Kim, Il-Ho 한국재료학회 2013 한국재료학회지 Vol.23 No.2

$Mg_{3-x}Zn_xSb_2$ powders with x = 0-1.2 were fabricated by mechanical alloying in a planetary ball mill with a speed of 350 rpm for 24 hrs and then hot pressed under a pressure of 70 MPa at 773 K for 2 hrs. It was found that there were systematic shifts in the X-ray diffraction peaks of $Mg_3Sb_2$ (x = 0) toward a higher angle with increasing Zn for both the powder and the bulk sample and finally the phase of $Mg_{1.86}Zn_{1.14}Sb_2$ was formed at the Zn content of x = 1.2. The $Mg_{3-x}Zn_xSb_2$ compounds had nano-sized grains of 21-30 nm for the powder and 28-66 nm for the hot pressed specimens. The electrical conductivity of hot pressed $Mg_{3-x}Zn_xSb_2$ increased with increasing Zn content and temperature from 33 $Sm^{-1}$ for x = 0 to 13,026 $Sm^{-1}$ for x = 1.2 at 323 K. The samples for all the compositions from x = 0 to x = 1.2 had positive Seebeck coefficients, which decreased with increasing Zn content and temperature, which resulted from the increased charge carrier concentration. Most of the samples had relatively low thermal conductivities comparable to the high performance thermoelectric materials. The dimensionless figure of merit of $Mg_{3-x}Zn_xSb_2$ was directly proportional to the Zn content except for the compound with Zn = 1.2 at high temperature. The $Mg_{3-x}Zn_xSb_2$ compound with Zn = 0.8 had the largest value of ZT, 0.33 at 723 K.

설계경기 - 울산과학기술대학교 첨단생체소재연구센터

김인기,Kim, In-Gi 대한건축사협회 2012 建築士 Vol.2012 No.4

용융법과 기계적 합금화에 의한 열전재료 Mg₃Sb₂의 제조

김인기,Kim, In-Ki 한국결정성장학회 2012 韓國結晶成長學會誌 Vol.22 No.4

Mg와 Sb 분말을 사용하여 1173 K에서 결정성이 좋은 단일상의 $Mg_3Sb_2$ 합금을 제조하였다. 이 합금의 열전성능지수 zT는 온도상승에 따라 크게 증가하였고 593 K에서 $2.39{\times}10^{-2}$의 값을 나타내었다. 얻어진 $Mg_3Sb_2$ 합금을 planetary ball mill에서 12~48시간 볼밀링할 경우 주 결정상 $Mg_3Sb_2$는 유지가 되었으나 결정성이 나빠졌고 금속원소 Sb상이 나타났다. Mg와 Sb를 섞고 24시간 볼밀링에 의한 합금화 방법으로 합성할 경우 원소금속 Sb가 나타나지 않은 $Mg_3Sb_2$ 결정상을 얻을 수 있었다. A single phase $Mg_3Sb_2$ alloy was synthesized by melting the mixture of Mg and Sb metal powders at 1173 K. The figure of merit of the $Mg_3Sb_2$ prepared by melting method increased with temperature and showed a value of $2.39{\times}10^{-2}$ at 593 K. When the $Mg_3Sb_2$ powders were milled at high speed in a planetary ball mill for 12~48 h, Zintle phase ($Mg_3Sb_2$) was maintained as a main phase, but its crystallinity became deteriorated and elemental Sb phase appeared. Sb phase free $Mg_3Sb_2$ could be obtained by the mechanical alloying of high speed ball milling for 24 h using elemental Mg and Sb powder mixtures.

알기쉬운 재료학-버터

김인기,Kim, In-Gi 대한제과협회 1996 베이커리 Vol.11 No.-

악취 또는 VOCs를 제거할 수 있는 필터 기술

김인기,Kim, In-Gi 한국공기청정협회 2008 空氣淸淨技術 Vol.21 No.4

열전재료 Zn_1-xAg_xSb의 제조와 특성

김인기,오한준,장경욱,Kim, In-Ki,Oh, Han-Jun,Jang, Kyung-Wook 한국결정성장학회 2017 韓國結晶成長學會誌 Vol.27 No.4

$Zn_{1-x}Ag_xSb$에서 Ag의 함량이 0~0.2인 열전화합물을 진공용해법으로 제조하여 결정상과 열전물성을 조사하였다. x = 0.05에서는 금속성 free Sb 상이 많이 생성되었고 이로 인해 전기전도도와 power factor가 크게 증가하였고 power factor는 제벡계수보다는 전기전도도에 의해 더 큰 영향을 받았다. x = 0.1 이상에서는 $Ag_3Sb$ 상이 현저하게 늘어났고 free Sb 피크는 약화되었다. 이에 따라 전기전도도와 power factor는 감소하기 시작하였고 이러한 경향은 더 많은 Ag가 첨가되면서 더욱 뚜렷하게 나타났다. Thermoelectric compounds of $Zn_{1-x}Ag_xSb$ with x = 0~0.2 were prepared by vacuum melting and quenching process and their crystal phases and thermoelectric properties were examined. It was found that free metallic Sb phases were formed in the compound with x = 0.05, leading to increasing the electrical conductivities. The power factors were significantly affected by the electrical conductivity rather than Seebeck coefficient. When x > 0.05, the peak intensities of $Ag_3Sb$ phases in XRD patterns were increased and those of free Sb phases were weakened. These changes of second phases resulted in decreasing the electrical conductivities and the power factors and became more obvious in the compound with x = 0.2.

기계적 합금법에 의한 Mg₃Bi₂와 Mg₃Sb₂ 화합물 및 복합체의 제조

김인기,Kim, In-Ki 한국결정성장학회 2013 韓國結晶成長學會誌 Vol.23 No.4

기계적 합금법을 이용하여 Mg, Sb, Bi을 planetary 볼밀에서 24~48시간 볼 밀링하여 $Mg_3Sb_2$와 $Mg_3Bi_2$ 단일 결정상의 합금분말을 얻었다. 출발조성은 $Mg_3Sb_2$상의 경우 3Mg : 1.8Sb, $Mg_3Bi_2$상은 3Mg : 1.6Bi이었다. 얻어진 두 합금 분말을 여러 비율로 혼합하여 70 MPa의 압력 하, 723 K에서 1시간 가압소결하여 $Mg_3Sb_2-Mg_3Bi_2$ 복합체를 제조하였다. 복합체의 주 결정상은 $Mg_3Bi_2$상과 유사한 안정한 상이었고 미량의 Bi상이 존재하였다. EDS 맵핑결과 가압소결체들의 조성분포는 불연속적이며 독립적으로 나타나서 $Mg_3Sb_2-Mg_3Bi_2$계 복합체가 제조되었다는 것을 확인할 수 있었다. Single phase crystalline powders of $Mg_3Sb_2$ and $Mg_3Bi_2$ were prepared by mechanical alloying Mg, Sb and Bi metals with planetary ball milling for 24~48 h. The compositions of starting raw materials for single phase $Mg_3Sb_2$ and $Mg_3Bi_2$ were 3Mg : 1.8Sb and 3Mg : 1.6Bi, respectively. Two types of mechanically alloyed powders obtained were mixed at some ratios for the fabrication of $Mg_3Sb_2-Mg_3Bi_2$ composites and then hot pressed under uniaxial pressure of 70 MPa at 723 K for 1 h. The main phase of composites was a stable phase similar to $Mg_3Bi_2$ phase with a small amount of Bi phase. The distributions of Sb and Bi elements on EDS mapping images were discontinuous and their compositional contours were clear, which means that the hot pressed specimens were composites composed of two compounds of $Mg_3Sb_2$ and $Mg_3Bi_2$.

냉간 압축 성형한 Mg₃Sb₂ 열전재료의 고상 반응 소결

김인기,장경욱,오한준,Kim, In-Ki,Jang, Kyung-Wook,Oh, Han-Jun 한국결정성장학회 2014 韓國結晶成長學會誌 Vol.24 No.4

상온 압축 성형 후 고상 반응 소결 공정을 통하여 $Mg_3Sb_2$ 소결체를 제조하고자 하였다. Mg과 Sb의 성분의 몰비와 반응온도에 따른 결정상의 변화를 조사하였다. 773~843 K에서 얻어진 고상반응 소결체들은 전형적인 $Mg_3Sb_2$ 결정상을 형성하였으나 소결체의 위치에 따라 약간 다른 상적 구성을 보였다. 소결체 하단 부위에서 전형적으로 얻어지는 결정상이 얻어졌으며 823 K 온도에서는 Mg : Sb = 3.15 : 1.85 조성일 때, 843 K 온도에서는 Mg의 몰 수가 3.10 이상인 모든 조성에서 ${\alpha}-Mg_3Sb_2$ 상과 정확히 일치하는 결정상이 얻어졌다. 미량 남아있는 Mg 성분은 응고 후 냉각 시 ${\alpha}-Mg_3Sb_2$ 상으로부터 석출된 것으로 보인다. We intended to prepare $Mg_3Sb_2$ compound bodies through solid state reactive sintering after cold-pressing mixtures of elementary Mg and Sb powders and investigated the crystal phases of the sintered bodies according to Mg/Sb mole ratios and reaction temperatures. The $Mg_3Sb_2$ bodies sintered at the temperatures of 773~843 K showed typical crystalline phases of $Mg_3Sb_2$ compounds, but their diffraction angles in XRD patterns were slightly different along with the vertical axis of the bodies obtained. All the bottom parts of the sintered $Mg_3Sb_2$ bodies were composed of the typical crystalline phases of $Mg_3Sb_2$ compounds and their diffraction angles were completely in accord with those of the ${\alpha}-Mg_3Sb_2$ phase, when Mg : Sb = 3.15 : 1.85 at 823 K, or when the Mg moles were greater than or equal to 3.10 at 843 K. It was considered that the slightly remaining Mg phases were formed by precipitation from ${\alpha}-Mg_3Sb_2$ phases during the solidification process of liquid phase.

회원작품: 울산대학교 건축대학관

김인기,김영수,Kim, In-Ki,Kim, Yung-Soo 대한건축사협회 2011 建築士 Vol.2011 No.5