http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
이현호 한국구조물진단유지관리공학회 2014 한국구조물진단유지관리공학회 논문집 Vol.18 No.5
본 연구의 목적은 I형 스트럿 및 S형 스트럿 강재댐퍼의 변위 및 속도의존성을 평가하는 것이다. 이를 위하여 12개의 강재댐퍼를 제작하여 의존성 평가를 실시하였으며, 시험 변수는 스트럿 형상, 목표 변위 및 속도이다. 의존성 시험에 의한 반복횟수 평가결과, ASCE 7-10에서 규정한 최소 반복횟수 5회를 충분히 상회하는 것으로 평가되었다. 변위의존성 평가결과, 큰 목표변위 (50mm)의 반복횟수 및 누적에너지소산능력은 적은 목표변위 (25mm)에 비하여 감소하였다. 또한 짧은 목표변위보다 큰 항복강도 및 조기파단을 나타내었다. 속도의존성평가에서는 빠른 목표속도 (60mm/sec)의 반복횟수 및 누적에너지소산능력이 느린 목표속도 (40mm/sec)에 비하여 감소하였다. 결과적으로강재댐퍼의 기본 물성, 의존성 평가, 누적에너지소산능력 평가결과, S형 스트럿을 가지는 강재댐퍼의 의존 능력이 I형보다 윌등히 우수한것으로 평가되었다. The purpose of this study is the displacement and velocity dependence evaluation of I type and S type metallic dampers. Forthis purpose, 12 metallic damper specimens are prepared and dependence test are performed. Test variables are strut type, displacement and velocity dependence. From the evaluation results of dependence tests, number of cycles are fully exceeded than minimum 5 cycles described in ASCE 7-10. According to displacement dependence test results, larger target displacement (50mm) shows lower cyclic numbers and cumulated energy dissipated area than lower target displacement (25mm). Also it show higher strength and early failure than short target displacement. In velocity dependence evaluation, fast target velocity (60mm/sec) shows lower cyclic numbers and cumulated energy dissipated area than target velocity (40mm/sec). As a results of basic properties, dependence evaluation and cumulated energy dissipated area evaluation, dependence capacity of S type metallic damper is far superior than I type.
타이타늄 산화물층을 도입한 고분자 태양전지의 효율 향상 연구
이현호,이광희,김선희,김진영,김희주,박성흠,조신욱 한국물리학회 2005 새물리 Vol.50 No.3
We demonstrate that high eciency polymer solar cells can be fabricated using titanium oxide(TiOx) as an optical spacer. When a TiOx layer is deposited via a typical sol-gel process between the active layer and cathode, the devices exhibit almost 50 % enhancement in the external quantum eciency and in the power conversion eciency. The a TiOx layer acts as an ideal optical spacer by modifying the distribution of the optical electric eld energy inside the device, thereby inducing more photogenerated charge carriers in the polymer solar cell.
이현호,박지연,김상준,이유진,양지원 한국지하수토양환경학회 2003 지하수토양환경 Vol.8 No.1
본 연구에서는 동전기적 토양복원에 적합한 계면활성제를 선정하는 방법으로 세 가지 계면활성제, APG, Brij30, SDS를 대상으로 토양에 흡착되는 계면활성제의 양, phenanthrene에 대한 용해도, 생분해도 및 동전기적 토양정화 현상을 살펴보았다. Phenanthrene은 kaolinite에 최대 2,200 mg/kg dry soil까지 흡착되었으며, APG, Brij30, SDS는 토양 1kg당 각각 40, 7, 4g이 흡착되었다. Phenanthrene의 용출효율은 계면활성제에 대해서 Brij30>SDS>APG의 순서로 나타났으며, 생분해도는 APG>Brij30>SDS순서로 나타났다. 동전기 정화실험에서는, 세 가지 계면활성제 중에서 전기삼투 흐름이 가장 원활한 APG가 phenanthrene에 대해 높은 제거율을 나타냈다. 이로부터 동전기적 토양복원에 적용하기 위해서는 계면활성제의 유기오염물에 대한 용출효율보다는, 전기삼투 흐름을 원활하게 할 수 있는 계면활성제를 선택하는 것이 보다 중요한 요소임을 알 수 있었다. Three different surfactants, APG, Brij30, and SDS, were tested to study the characteristics of sorption on soil surfaces, washing ability, biodegradability, and electrokinetic removal. Kaolinite and phenanthrene were selected as a model soil and a representative HOC, respectively. Phenanthrene was sorbed on kaolinite up to 2,200 mg/kg dry soil. The APG, Brij30, and SDS were sorbed on soil to 40, 7, and 4g/kg soil, respectively. The washing ability of phenanthrene was in order of Brij30>SDS>APG. The biodegradability tested with sludge was in order of APG>Brij30>SDS. In the electrokinetic test, the highest removal efficiency was obtained with APG that exhibited the highest electroosmotic flow. To increase the removal efficiency of HOC in the electrokinetic remediation, the most important factor was the selection of surfactant which maximized the electroosmotic flow.
이현호 한국구조물진단유지관리공학회 2010 한국구조물진단유지관리공학회 논문집 Vol.14 No.2
본 연구의 목적은 내진규준이 적용되기 이전에 건설된 역사건물의 내진성능 평가 및 내진보강이다. 이를 위하여 2층 RC 역사건물의 내진성능이 평가되었다. 동적해석에 의한 층간변위비 및 층전단력 평가결과, 층전단력이 설계기준의 밑면전단력을 초과하는 것으로 평가되어 적절한 내진보강이 필요한 것으로 평가되었다. 내진성능 향상을 위하여 총 4개의 강재댐퍼가 사용되었다. 해석 변수는 강재댐퍼 형상 및 설치 방법이다. 동적해석결과 역 K가새로 설치되는 슬릿댐퍼가 다른 댐퍼 형상 및 설치 방법보다 우수한 내진성능을 가진 것으로 평가되었다. The purpose of this research is a seismic capacity evaluation and strengthening of existing railway station buildings, which were constructed before the seismic design code activated. The seismic capacity of 2nd story RC station building is evaluated by using nonlinear time-history analysis. Analysis results are checked by story drift ratio and story shear, which are described in design code. As a result, the story shears are exceeding the base shear of the design code, the appropriate seismic strengthening methods are needed. To improve the seismic capacity, metallic dampers are used. Evaluation parameters are metallic damper shape and damper installation methods. Dampers are installed in four places in X and Y directions of station buildings. By reviewing of time-history analysis results, the metallic damper, which is installed inverted K-brace type, shows a better seismic performance than other damper shape and installation methods.