http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
재래식 및 개량식 된장의 아이소플라본 분포 및 $\beta$-glucosidase 활성 연구
이승욱,박영우,장판식,이재환,Lee, Seung-Wook,Park, Yong-Woo,Chang, Pahn-Shick,Lee, Jae-Hwan 한국식품과학회 2010 한국식품과학회지 Vol.42 No.2
숙성기간이 다른 재래식 된장 12종과 개량식 된장 4종의 아이소플라본과 $\beta$-glucosidase 활성도를 비교하였다. 재래식 된장의 전체 아이소플라본 함량(TI)은 $370-723\;{\mu}g/g$이었고, 개량식 된장은 $179-537\;{\mu}g/g$으로 유의적으로 낮은 함량을 보였다. 된장의 주요 아이소플라본은 비배당체 형태였으며 재래식 된장의 경우 42.98-89.96%, 개량식 된장은 35.51-93.48%이었다. 아이소플라본 함량 분포에 대한 주성분 분석 결과 재래식 된장은 개량식 된장과 차별화가 가능하였다. 개량식 된장의 경우 $\beta$-glucoside 형태는 검출되지 않았는데 이는 과도한 열처리를 받았거나 발효에 관여한 미생물의 $\beta$-glucosidase 활성이 높았음을 의미한다. 된장시료에서 $\beta$-glucosidase 활성도는 날콩에 비해 낮았으며 재래식 및 개량식 된장간에 유의적인 차이 및 아이소플라본의 분포와의 상관관계는 명확하지 않았다. Isoflavone distribution and $\beta$-glucosidase activity in 16 commercially available doenjang samples were determined. Twelve of the samples were home-made doenjang (HMD) with a relatively long fermentation period and 4 of the samples were factory-produced doenjang (FPD) from four different manufactures. Total isoflavones (TI) in the HMD ranged from $370-723\;{\mu}g/g$, while those in FPD ranged from $179-537\;{\mu}g/g$. The isoflavone distribution in HMD was different from those in FPD. Generally, the TI in HMD was higher than those in FPD. The major isoflavone was aglycones, which ranged from 42.98 to 89.96% in HMD and from 35.51 to 93.48% in FPD. Isoflavones in the $\beta$-glucoside forms were not detected in tested FPD samples. Principal components analysis (PCA) of the isoflavone profiles showed that HMD were differentiated from FPD. First principal component (PC1) and second principal component (PC2) expressed 43.6 and 22.9% of the data variability, respectively. $\beta$-Glucosidase activity in doenjang was lower than that in raw soybeans. The results of this study can be used to understand the differences in the isoflavone distribution in traditionally manufactured and factory produced doenjang.
측정기에 따른 고에너지 X-선의 표면 선량 및 최대 선량 지점 고찰
이용하(Yong Ha Lee),박경란(Kyung Ran Park),이종영(Jong Young Lee),이익재(Ik Jae Lee),박영우(Young Woo Vahc),이강규(Kang Kyoo Lee) 대한방사선종양학회 2003 Radiation Oncology Journal Vol.21 No.4
목 적: 고에너지 X-선의 표면선량과 선량보강(build-up) 영역에서의 선량분포는 일반적으로 방사선 계측에 사용되는 전리함 측정기로는 정확한 선량분포를 얻기가 매우 어렵다. 본 연구는 고에너지 X-선 선량계측에 보편적으로 사용되고 있는 여러 측정기를 이용하여 팬톰 표면에서의 흡수선량과 최대 선량 지점(dmax)을 측정하여 측정기 사이의 정확성을 비교 분석하고, 각 치료기관에서 보편적으로 사용되는 측정기 중 표면 선량 측정에 적절한 측정장치를 제안하고 그 유용성을 제시하고자 한다. 대상 및 방법 : 본 실험에서는 6 MV와 15 MV X-선에 대해 조사면이 10×10 cm 2,SSD=100cm에서 TLD, 팀블형 전리함(thimble type ion chamber), 다이오드 검출기, 다이아몬드 검출기와 Markus 평행판 전리함 등을 이용하여 심부선량백분율(percent depth dose: PDD)을 측정하여, 표면 선량(surface dose)과 최대 선량 지점(dmax)을 비교 분석하고,또한 TLD 측정 시와 동일 조건으로 Monte Carlo 계산을 실행하여 TLD의 측정 결과와 비교하였다. 결 과: 6 MV와 15 MV X-선에 대해 Markus 평행판 전리함을 이용하여 측 정 한 표 면 선 량 은 각각 29.31%와 23.36%으로 측정되었으며, TLD는 37.17%와 24.01%, 다이아몬드 검출기는 34.78%와 24.06%, 다이오드 검출기는 38.18%와 27.8%, 팀블형 전리함은 47.92%와 36.01% 였으며, Monte Carlo 계산에 의한 표면 선량 값은 6 MV X-선에 대해 TLD 측정 시와 동일한 조건으로 팬톰 내에 가상적인 TLD를 삽입한 경우 36.22%로 실제 측정값 37.17%와 유사하였다. 최대 선량지점의 깊 이는 모든 측정기에서 6 MV X-선에 대하여 14˜16mm, 15 MV X-선에서는 27˜29mm 사이의 측정기에 따라 작은 차이를 보였다. 결 론: 표면 선량의 경우에는 측정기에 따라 현저한 차이를 보였으며 Markus 평행판 전리함이 사용된 측정기 중 가장 정확한 결과를 보였고, 팀블형 전리함의 경우 다른 측정기에 비해 약 10% 이상 높은 선량을 보여 피부 표면에 가까이 위치한 종양에 대한 방사선 치료계획시에는 임상에서 가장 보편적으로 사용되고 있는 팀블형 전리함의 선량 값을 그대로 사용하기에는 많은 오류가 발생하므로 가능한 표면 선량 측정에 적절한 측정기를 선택하여 사용하거나 측정기 특성을 고려한 보정이 필요할 것으로 생각된다. 최대 선량 지점(dmax)의 결과는 모든 측정기에서 비슷한 결과를 나타내고 있어 본 실험에서 사용한 모든 측정기는 그 특성에 상관없이 최대 선량 지점 측정에 사용이 가능함을 알 수 있었다. Purpose It is difficult to exactly determine the surface dose and the dose distribution in buildup region of hi gh energy X-rays by using the conventional ion chamber. The aim of this study is to evaluate the accuracy of widely used dosimetry systems to measure the surface dose and the depth of maximum dose (d max). Materials and Methods: We measured the percent depth dose (PDD) from the surface to the dmax in either a water phantom or in a solid water phantom using TLD-100 chips, thimble type ion chamber, d i o de detector, diamond detector and Markus parallel plate ion chamber for 6 MV and 15 MV X-rays, 10 × 10 cm 2, at SSD=100cm. We analysed the surface dose and the dmax. In order to verify the accuracy of the TLD data, we executed the Monte Carlo simulation for 6 MV X-ray beams. Results The surface doses in 6 MV and 15 MV X-rays were 29.31% and 23.36% for Markus parallel plate ion chamber, 37.17% and 24.01% for TLD, 34.87% and 24.06% for diamond detector, 38.13% and 27.8% f or diode detector, and 47.92% and 36.01% for thimble type ion chamber, respectively. In Monte Carlo simulation for 6 MV X-rays, the surface dose was 36.22%, which is similar to the 37.17% of the TLD measurement data. The dmax in 6 MV and 15 MV X-rays was 14 16 mm and 27 29 mm, respectively. There was no significant difference in the dmax among the detectors. Conclusion There was are markable difference in the surface dose among the detectors. The Markus parallel plate chamber showed the most accurate result. The surface dose of the thimble i on chamber was 10% higher than that of other detectors. We suggest that the correction should be made when the surface dose of the thimble ion chamber is used for the treatment planning for the superficial tumors. All the detectors used in our study showed no difference in the dmax.
말판증후군과 동반된 해리성 대동맥류에 대한 대동맥 근부 개형술(改型術): Yacoub-David 수술법
박형주,이승진,박영우,최태명,신원용,곽수달,고정관,이철세,염욱,Park, Hyung-Joo,Lee, Seong-Jin,Park, Young-Woo,Choi, Tai-Myung,Shin, Won-Yong,Kwak, Soo-Dal,Ko, Jeong-Kwan,Lee, Cheol-Sae,Youm, Wook 대한흉부심장혈관외과학회 2001 Journal of Chest Surgery (J Chest Surg) Vol.34 No.7
순턴향대학 턴안병원 흥부외과에서는 Stan$\ulcorner$old type A급성 대동맥 박리증, 대동맥 근부 동맥류 및 대동맥 폐쇄부전을 보인 45세 말판 증후군 환자에게 24m Hemashield 도관을 이용하여 Yacoub-David 수술법에 의한 대동맥 근부 개형술(aortic root remodeling procedure)을 시행하였다 수술은 환자의 대동맥 판막을 보존하면서 대동맥등을 포함한 대동맥 근부의 질병조직을 모두 제거한 후, 글이 발살바동 모양으로 3등분된 인조혈관으로 대동맥등으로부터 상행 대동맥가지 대치하는 방법으로 하였다. 환자는 수술 후 양호한 회복을 보였고 대 동맥 판막의 역류는 완전히 교정되었다. We operated on a Marfan patient who had Stanford type A acute aortic dissection, aortic root aneurysm, and aortic regurgitation. The Yacoub-David aortic root remodeling procedure which preserves native aortic valve and replaces all three aortic sinuses and ascending aorta by a Dacron graft, was applied for this patient. A 24mm Hemashield graft was designed to three tongues at the aortic root end to meet the shape of the Valsalva sinuses. The patient recovered from the procedure uneventfully and there was no aortic regurgitation posto-peratively.
접촉부품의 전기적 미동마멸 부식에 대한 신뢰성 설계기술
이강용(Kang Yong Lee),박영우(Young Woo Park) 대한기계학회 2005 대한기계학회 춘추학술대회 Vol.2005 No.5
The essential prerequisite experimental approach is conducted to establish the reliability design technology for electrical contact parts. To realize the precise and reliable experiment, the creatively designed fretting corrosion device is developed. For a commercial electric connector material, a single contact fretting corrosion testing was conducted with the accelerated conditions. In this work, the increased electrical contact resistance and intermittent extinction are observed. Particularly, at the center of the fretting displacement, the electrical contact resistance is higher than at the end of that, and this effect increases with the progress of the fretting cycle. The tendency of the increased electrical contact resistance was analysed with the three steps, and the degradation mechanisms of each step were investigated.
유전 알고리즘을 이용한 AA6061 알루미늄 판재의 레이저-아크 하이브리드 용접 공정 변수 최적화
장일광(Ilkwang Jang),박영우(Young Woo Park),김항래(Hang Rae Kim),이강용(Kang Yong Lee) 대한기계학회 2008 대한기계학회 춘추학술대회 Vol.2008 No.5
Genetic algorithm has been carried out to develop a new approach for optimization of Nd:YAG laser and MIG hybrid welding parameters. The characteristic of weld ability is dependent on various process parameters. the parameters chosen for current study include laser power, laser focus, traveling speed, wire feed rate, root opening gap, and arc voltage. The Butt welding design were chosen for aluminum alloy 6061-T6 plate and the ultimate tensile strength were measured for evaluating multiple parameters. Base on the results of genetic algorithm, the optimal process parameters were obtained. It is observed that the results obtained by using the optimal parameters are much improved compared to those from the preliminary set of experimental parameters.
미동마멸부식 환경에서 구리합금 전기접촉재의 열화현상 연구
정대기(Dae-Ki Jeong),박영우(Young-Woo Park),이강용(Kang-Yong Lee) 대한기계학회 2008 대한기계학회 춘추학술대회 Vol.2008 No.5
The fretting corrosion experiment of Cu alloy contact is executed under room environmental condition. The variation of contact resistance with fretting cycle is observed. The simulation model of contact resistance variation under various oxide fractions is constructed with theoretical model. The copper oxide is assigned on the contact area with various fractions by the random distribution technique with finite element method. The calculated contact resistance at each oxide area fraction is compared with experimental contact resistance.