http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Yttria를 도핑한 세리아 안정화 지르코니아 세라믹스의 미세구조
이종국,강현희,서동석,이은구,김환,Lee, J.K.,Kang, H.H.,Seo, D.S.,Lee, E.G.,Kim, H. 한국재료학회 1999 한국재료학회지 Vol.9 No.8
세리아 안정화 지르코니아 성형체내에 이트리아를 침적법으로 도핑시켜 미세구조를 관철하였다. 도핑된 이트리아의 양과 열처리 조건을 제어하여 입계가 변형된 불규칙 입자형상의 미세구조를 형성시켰으며, 이때 입자형상의 불규칙 정도는 첨가된 이트리아의 양에 비례하였다. 0.2M 농도의 Y(NO$_3$)$_3$.6$H_2O$의 수용액에 재침적하여 1$650^{\circ}C$에서 2시간 열처리한 시편의 미세구조는 표면부와 내부 모두에서 불규칙 입자형상을 나타내었으며, 입자의 불규칙도도 가장 큰 것으로 나타났다. 가압소결을 행한 결과 입계가 불규칙하게 변화된 미세구조가 창출됨과 동시에 평균입자 크기가 0.3$\mu\textrm{m}$ 가량인 미세한 소결체를 제조할 수 있었으며, 상분석 결과 대부분 정방정상을 유지하고 있었다. 불규칙 입자형상의 미세구조를 가진 시편의 파괴인성값은, 정상적인 입자형상을 갖는 시편에서의 압흔 균열 크기로부터 비교 유추한 결과 17.6MPa.m(sup)1/2 이상인 것으로 나타났다. Yttia-doped ceria-stabilized ziconia polycrystals(Ce-TZP) was prepared by dipping method and its microstructure was investigated. By controlling doped-yttria content and annealing condition, yttria-doped Ce-TZP showed the microstructure with irregular grain shape and undulated grain boundary. Irregularity of grain shape increased with the amount of yttria doped, and severe undulated grain boundary was observed mainly at the surface region. In the case of yttria-doped Ce-TZP annealed at 1$650^{\circ}C$ for 2h after two dipping times into yttrium nitrate solution of 0.2M, it showed irregular grain shape both at the surface and at the interior region as well as the most severe irregularity. Hot pressed specimen had mean grain size of 0.3$\mu\textrm{m}$ and undulated grain boundary. All specimens with irregular grain shape were retained the tetragonal phase. The fracture toughness of yttria-doped Ce-TZP with irregular grain shape was over the value of 17.6MPa.m(sup)1/2.
이종국,박종곤,이은구,김환,Lee, J.K.,Park, J.G.,Lee, E.G.,Kim, H. 한국세라믹학회 2000 한국세라믹학회지 Vol.37 No.3
Silicon carbide with sialon was prepared by hot pressing and transient liquid-phase sintering, and the effects of sintering atmosphere and starting phases on their microstructural characteristics were investigated. The sintered SiC with Sialon composition(Y2O3, AlN, Si3N4) in argon atmosphere had high sintered density and large aspect ratio. But sintered specimens in nitrogen atmosphere showed low aspect ratio and small grian size, becuase of the retardation of phase transformation and grain growth. Addition of Y-Sialon powder to SiC also retarded the phase transformation to ${\alpha}$-SiC from ${\beta}$-SiC and densification. The SiC specimen prepared from the starting ${\beta}$-SiC powder with Sialon composition(Y2O3, AlN, Si3N4) showed the highest fracture toughness about 6.0 MPa$.$m1/2.
최정열(J.-Y. Choi),장근진(K.-J. Jang),김성돈(S.-D. Kim),정인석(I.-S. Jeung),이종국(J.-K. Kim) 한국추진공학회 2013 한국추진공학회 학술대회논문집 Vol.2013 No.12
본 연구에서는 극초음속 노즐 설계를 위한 설계 절차를 수립하였다. 노즐 목에서 확산 영역까지 특선곡선해법을 이용하여 기본 설계를 수행하며, 기본 설계에 대한 격자를 작성하여 MOC 설계를 확인하기 위한 비점성 CFD 해석을 수행한다. 비점성 결과를 바탕으로 점성 해석을 수행하여 기본 형상에 대한 경계층을 보정하여 격자를 다시 생성한 후, 결과 확인을 위한 점성 해석을 다시 수행한다. 전 과정은 자동 일괄 처리토록 작성 되었으며, 여러 경계층 보정 방법에 따른 결과들을 비교 검토 하였다. A design procedure is established to design hypersonic nozzles. The basic design is carried out by the MOC for the throat region to the divergence region. Grid generation is carried out for the basic design, followed by the inviscid CFD analysis to confirm the MOC design. The inviscid solution is used as an initial condition for viscous simulation. Then, boundary layer thicknesses are evaluated from the results viscous solution. The BLC is made for the basic geometry and the computational grid is reconstructed. Finally, viscous simulation is carried out again to confirm the BLC. All this procedure is made automatically by using the batch processing. Various BLC approaches were compared through the present study.