Application of model reduction technique and structural subsection technique on optimal sensor placement of truss structures

Lu, Lingling,Wang, Xi,Liao, Lijuan,Wei, Yanpeng,Huang, Chenguang,Liu, Yanchi Techno-Press 2015 Smart Structures and Systems, An International Jou Vol.15 No.2

An optimal sensor placement (OSP) method based on structural subsection technique (SST) and model reduction technique was proposed for modal identification of truss structures, which was conducted using genetic algorithm (GA). The constraints of GA variables were determined by SST in advance. Subsequently, according to model reduction technique, the optimal group of master degrees of freedom and the optimal objective function value were obtained using GA in a case of the given number of sensors. Correspondingly, the optimal number of sensors was determined according to optimal objective function values in cases of the different number of sensors. The proposed method was applied on a scaled jacket offshore platform to get its optimal number of sensors and the corresponding optimal sensor layout. Then modal kinetic energy and modal assurance criterion were adopted to evaluate vibration energy and mode independence property. The experiment was also conducted to verify the effectiveness of the selected optimal sensor layout. The results showed that experimental modes agreed reasonably well with numerical results. Moreover the influence of the proposed method using different optimal algorithms and model reduction technique on optimal results was also compared. The results showed that the influence was very little.

Novel Flower-Like CuO/N-rGO as Enhanced Electrocatalyst for Oxygen Reduction Reaction

Lijuan Zhang,Jinhua Lu,Jianfeng Wei,Yan Wang 성균관대학교(자연과학캠퍼스) 성균나노과학기술원 2019 NANO Vol.14 No.10

Flower-like copper oxide (CuO)/nitrogen-doped reduced graphene oxide (N-rGO) was synthesized through a one-pot microwave hydrothermal method by using polyvinylpyrrolidone (PVP) as surfactant. In the process, in situ formation of nanomaterial CuO, reduction of graphene oxide and doping of nitrogen species occurred simultaneously in urea solution. The structural and surface properties of the material were investigated by field emission scanning electron microscopy (FESEM) and transmission electron microscopies (TEM), the energy dispersive spectroscopic (EDS) and powder X-ray diffraction (XRD). This showed the flower-like CuO with an interconnected architecture was successfully uniformed and grown on the surface of N-rGO. Moreover, the surfactant PVP and urea were found to be the key factors to control the morphology of the CuO nanostructure. Electrochemical investigations indicated that the CuO/N-rGO composite exhibited a significantly enhanced ORR activity in comparison to pure CuO and N-rGO in an alkaline solution. The enhancement in ORR activity of CuO/N-rGO composite can be attributed to the synergistic effects of good electron transport from N-rGO as well as abundance of exposed catalytic sites and meso/macroporosity from CuO nanostructures.

Characterization and evolutionary analysis of Brassica species-diverged sequences containing simple repeat units

Lijuan Wei,Meili Xiao,Annaliese S. Mason,Bi Ma,Kun Lu,Jia Na Li,Link Katrin,Donghui Fu 한국유전학회 2013 Genes & Genomics Vol.35 No.2

Brassica species, B. napus (canola), B. rapa and B. oleracea, are important sources of nutritionally valuable vegetable oil and protein-rich meal for animals and humans. Sequencing of the model plant Arabidopsis thaliana, has opened the way for investigations into the complex structure of the Brassica genomes, offering important insight into their evolution and composition. We use this sequence information for the characterization and functional analysis of SSR sequences that have diverged between the Brassica species. A total of 56 species-diverged sequences containing simple repeat units (SDS-SSR) of B. napus and its diploid progenitor species B. rapa and B. oleracea were isolated and characterized. Of these, 40 sequences showed homology with other Brassica sequences. Using the SSR Locator software, only 23 sequences were found to have SSRs,possibly due to the loss of SSR units in the process of species divergence. Sequence alignments with A. thaliana revealed that these species-diverged SSR sequences were responsible for Brassica divergence for differences between Brassica species in several genomic regions. Six active genes related to transferase, protein, transcription factor and retroelements were found in the SDS-SSRs. These results will further improve our understanding of the characteristics of species-diverged SSR fragments and their contribution to genome differentiation.

Epithelial CST1 Promotes Airway Eosinophilic Inflammation in Asthma via the AKT Signaling Pathway

Du Lijuan,Xu Changyi,Tang Kun,Shi Jia,Tang Lu,Lisha Xiao,Lei Chengcheng,Liu Huicong,Liang Yuxia,Guo Yubiao 대한천식알레르기학회 2023 Allergy, Asthma & Immunology Research Vol.15 No.3

Purpose: Epithelial cystatin SN (CST1), a type 2 cysteine protease inhibitor, was significantly upregulated in asthma. In this study, we aimed to investigate the potential role and mechanism of CST1 in eosinophilic inflammation in asthma. Methods: Bioinformatics analysis on Gene Expression Omnibus datasets were used to explore the expression of CST1 in asthma. Sputum samples were collected from 76 asthmatics and 22 control subjects. CST1 mRNA and protein expression in the induced sputum were measured by real-time polymerase chain reaction, enzyme-linked immunosorbent assay, and western blotting. The possible function of CST1 was explored in ovalbumin (OVA)-induced eosinophilic asthma. Transcriptome sequencing (RNA-seq) was used to predict the possible regulated mechanism of CST1 in bronchial epithelial cells. Overexpression or knockdown of CST1 was further used to verify potential mechanisms in bronchial epithelial cells. Results: CST1 expression was significantly increased in the epithelial cells and induced sputum of asthma. Increased CST1 was significantly associated with eosinophilic indicators and T helper cytokines. CST1 aggravated airway eosinophilic inflammation in the OVA-induced asthma model. In addition, overexpression of CST1 significantly enhanced the phosphorylation of AKT and the expression of serpin peptidase inhibitor, clade B, member 2 (SERPINB2), while knockdown using anti-CST1 siRNA reversed the trend. Furthermore, AKT had a positive effect on SERPINB2 expression. Conclusions: Increased sputum CST1 may play a key role in the pathogenesis of asthma through involvement in eosinophilic and type 2 inflammation through activation of the AKT signaling pathway, further promoting SERPINB2 expression. Therefore, targeting CST1 might be of therapeutic value in treating asthma with severe and eosinophilic phenotypes.

Quantitative Evaluation of Gastrocnemius Medialis Stiffness During Passive Stretching Using Shear Wave Elastography in Patients with Parkinson's Disease: A Prospective Preliminary Study

Yin Lu,Du Lijuan,Li Yuanzi,Xiao Yang,Zhang Shiquan,Ma Huizi,He Wen 대한영상의학회 2021 Korean Journal of Radiology Vol.22 No.11

Objective: To prospectively investigate the feasibility of shear wave elastography (SWE) as a new quantitative and objective method for evaluating the stiffness of the gastrocnemius medialis (GM) muscle during passive stretching in patients with Parkinson’s disease (PD). Materials and Methods: SWE of the GM muscle was performed in 28 patients with PD [13 female and 15 male; mean age ± standard deviation (SD): 63.0 ± 8.5 years] and 12 healthy controls (5 female and 7 male; mean age ± SD: 59.3 ± 6.4 years) during passive ankle rotation. A Young’s modulus-ankle angle curve was constructed. The GM slack angle and baseline Young’s modulus (E0) were compared between the markedly symptomatic and mildly symptomatic sides of patients with PD, and healthy controls. Additionally, the correlation between the GM slack angle and the severity of rigidity, and the observer reproducibility of SWE in determining the GM slack angle were evaluated. Results: The GM slack angle was smaller on both the markedly and mildly symptomatic sides in patients with PD than in healthy controls (mean ± SD of -29.13° ± 3.79° and -25.65° ± 3.39°, respectively, vs. -21.22° ± 3.52°; p < 0.001 and p = 0.006, respectively). Additionally, in patients with PD, the GM slack angle on the markedly symptomatic side was smaller than that on the mildly symptomatic side (p = 0.003). The E0 value was lower on both the markedly and mildly symptomatic sides in patients with PD than in healthy controls (mean ± SD of 10.11 ± 2.85 kPa and 10.08 ± 1.88 kPa, respectively, vs. 12.23 ± 1.02 kPa; p = 0.012 and p < 0.001, respectively). However, no significant difference was found between the markedly and mildly symptomatic sides in patients with PD (p = 0.634). A negative linear relationship was observed between the GM slack angle and lower limb rigidity score on the markedly symptomatic side in patients with PD (r = -0.719; p < 0.001). The intraclass correlation coefficients for observer reproducibility of SWE ranged from 0.880 to 0.951. Conclusion: The slack angle determined by SWE may be a useful quantitative and reproducible method for evaluating muscle stiffness in patients with PD.

Amino ionic liquids-modified magnetic core/shell nanocomposite as an efficient adsorbent for dye removal

Jingjing Cheng,Lijuan Shi,Jianjun Lu 한국공업화학회 2016 Journal of Industrial and Engineering Chemistry Vol.36 No.-

Amino ionic liquids modified superparamagnetic mesoporous core/shell nanocomposite (Fe3O4@n-SiO2@mSiO2@DHIM-NH2) was synthesized to remove orange II and amaranth from water. Due to themultiple active sites of the introduced ionic liquids, the adsorbent presents superior adsorptionperformance and instantaneous adsorption capacity. The maximum adsorption capacities are reached atpH 2 due to the protonation of amino groups, which are 153.06 and 84.40 mg g 1 for orange II andamaranth, respectively. The good stability, rapid adsorption kinetics, large adsorption capacity, and highseparation efficiency make Fe3O4@nSiO2@mSiO2@DHIM-NH2 an efficient adsorbent for removinganionic contaminant from water.

Kidney Transplantation and Clinical Outcomes in Patients With Multiple Myeloma: Evidence From the United States Nationwide Inpatient Sample

Bo Yang,Lijuan Zhang,Xuechun Lu 대한배뇨장애요실금학회 2023 International Neurourology Journal Vol.27 No.3

Purpose: Patients with multiple myeloma (MM) are prone to developing persistent renal insufficiency. Novel therapeutic medications have improved long-term survival, making kidney transplantation (KT) a viable treatment option for MM survivors with end-stage renal disease. This study aimed to investigate the clinical outcomes in patients with MM who have received KT. Methods: Data from hospitalized patients ≥40 years of age with MM in the Nationwide Inpatient Sample 2016–2018 of the United States were queried. Patients were classified as having or not having undergone KT, as well as the stage of chronic kidney disease (CKD) for those who had not received KT. Propensity-score matching (PSM) was applied to balance the characteristics between the groups. Binary logistic regression was utilized to determine the associations between study variables and inhospital mortality, unfavorable discharges, prolonged length of stay (LOS), and major complications. Results: In total, 50,654 hospitalized patients with MM were identified, of whom 165 (0.3%) had received KT and 50,489 had not (5,905 at stage 5 CKD [CKD5D], 11,559 at stage 1–4 CKD [CKD1-4D], and 33,025 who were CKD-free). After PSM, between-group demographic and hospital-related characteristics were balanced. Binary regression analysis revealed that, compared to patients who were CKD-free, patients at CKD5D were significantly more likely to experience a prolonged LOS (odds ratio [OR], 1.31; 95% confidence interval [CI], 1.01–1.70) after adjusting for relevant confounders. Furthermore, compared to CKD-free patients, those who underwent KT were significantly more likely to have sepsis (OR, 1.48; 95% CI, 1.02–2.14). However, KT showed no association with the other adverse inpatient outcomes. Conclusions: Although KT is not common in MM patients, those who had undergone KT had comparable hospital outcomes to CKD-free patients. These data will help clinicians deliver better consultations to MM patients attempting to receive KT.

Parameter design method for the heat transfer performance of a fan-driven gearbox under planetary gear opening and oil-return conditions

Feng-xia Lu,Lijuan Yuan,Zhiqiang Zhao,Chun-lei Wang,He-yun Bao 대한기계학회 2021 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.35 No.9

On the basis of the computational fluid dynamics (CFD) method, this study calculates the surface convective heat transfer coefficients of the sun gear, planetary gear, ring gear, and bearing before and after the opening of the planetary gear of a fan-driven gearbox. A numerical fitting method is used to establish the calculation model of the convective heat transfer coefficients of the sun gear, planetary gear, ring gear, and bearing under the open-hole oilreturn condition. The convective heat transfer coefficients of each element are compared before and after the hole is bored, and the design method for the gearbox parameters with the objective of heat transfer performance is proposed. Result shows that the convective heat transfer coefficients of each element are increased after oil is returned from the hole of the planetary gear, and the change rate of the convective heat transfer coefficient of the raceway in the planetary gear bearing is the highest. When the aperture of the planetary gear is 7 mm and the number of holes is four, the heat transfer performance of the gearbox is the best. The maximum error between the convection heat transfer coefficient fitting formula value and the CFD simulation calculation result is 1.0558 %.

Preparation, Characterization and Luminescence Properties of a Novel 1,10-Phenanthroline-Functionalized Polyimide and Its Europium(III) Complexes

Zhiyong Chen,Jianjun Lu,Xuping Li,Xuting Jin,Lijuan Shi,Miaoqing Liu,Zhilin Sun 한국고분자학회 2015 Macromolecular Research Vol.23 No.9

A novel 1,10-phenanthroline-functionalized polyimide (CMPI-Phen) was prepared as polymer matrix by the nucleophilic substitution reaction between chloromethylated polyimide (CMPI) and 5-amino-1,10-phenanthroline (NH2-Phen). Then, two kinds of luminescent materials of 1,10-phenanthroline-functionalized polyimide containing Eu(III) complexes, were obtained by two different methods. Their structures and properties were characterized by Fourier transform infrared (FTIR) spectroscopy, 1H nuclear magnetic resonance (NMR) spectroscopy, elemental analysis, inductively coupled plasma (ICP), gel permeation chromatography (GPC), thermogravimetric analysis (TGA), X-ray diffraction (XRD), luminescence spectrometry, and luminescence decay analysis. Investigations revealed that both the CMPI-Phen-Eu(III) and CMPI-Phen-Eu(TTA)3 display highly efficient red emissions, suggesting their potential application as luminescent materials. However, compared with CMPI-Phen-Eu(III), CMPI-Phen-Eu(TTA)3, where TTA stands for thenoyltrifluoroacetone, exhibits more excellent and stable fluorescence intensity and longer luminescence lifetime (134.30 μs). The weight-average molecular weights of CMPI-Phen-Eu(III) and CMPI-Phen- Eu(TTA)3 are 2.40×104 and 3.11×104, respectively. The Eu contents of CMPI-Phen-Eu(TTA)3 and CMPI-Phen-Eu(III) were measured by ICP to be 7.00% and 5.92%, respectively. TGA demonstrated that both CMPI-Phen-Eu(III) and CMPI-Phen-Eu(TTA)3 have high thermal stability and their 5% loss weight temperatures were 356 and 280 oC, respectively. Moreover, both CMPI-Phen-Eu(III) and CMPI-Phen-Eu(TTA)3 were soluble in polar solvents such as dimethylformamide (DMF), dimethylacetamide (DMAc), 1-methyl-2-pyrrolidone (NMP), and dimethylsulfoxide (DMSO) under heating conditions, and could be easily cast into tough thin films.

Application of model reduction technique and structural subsection technique on optimal sensor placement of truss structures

Chenguang Huang,Lingling Lu,Lijuan Liao,Yanpeng Wei,Yanchi Liu,Xi Wang 국제구조공학회 2015 Smart Structures and Systems, An International Jou Vol.15 No.2

An optimal sensor placement (OSP) method based on structural subsection technique (SST) and model reduction technique was proposed for modal identification of truss structures, which was conducted using genetic algorithm (GA). The constraints of GA variables were determined by SST in advance. Subsequently, according to model reduction technique, the optimal group of master degrees of freedom and the optimal objective function value were obtained using GA in a case of the given number of sensors. Correspondingly, the optimal number of sensors was determined according to optimal objective function values in cases of the different number of sensors. The proposed method was applied on a scaled jacket offshore platform to get its optimal number of sensors and the corresponding optimal sensor layout. Then modal kinetic energy and modal assurance criterion were adopted to evaluate vibration energy and mode independence property. The experiment was also conducted to verify the effectiveness of the selected optimal sensor layout. The results showed that experimental modes agreed reasonably well with numerical results. Moreover the influence of the proposed method using different optimal algorithms and model reduction technique on optimal results was also compared. The results showed that the influence was very little.