http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
When is the Optimal Time to Control High Heart Rate with Ivabradine during Coronary CT Angiography?
남수진(Soo-Jin Nam),전우인(U-In Jeon),김웅기(Woong-Ki Kim),고성민(Sung-Min Ko) 대한CT영상기술학회 2021 대한CT영상기술학회지 Vol.23 No.2
움직임에 취약한 심장은 CCTA검사시 영상화하기에 어렵고, 환자의 호흡과 심박동수는 영상의 질을 좌우하는 요소로 심박동수를 적정하게 조절하여 심장 CT검사를 진행한다는 것은 심장의 박동수에 따라 달라지는 심혈관의 두께와 위치를 큰 변화없이 최적의 영상을 획득할 수 있다는 의미이다. 높은 심박수를 가진 환자들은 최적의 영상획득을 위해 심박동수를 조절하는 약물을 투여하면 검사가 용이해진다. 이바브라딘을 복용하여 심박동수를 낮추는 효과가 나타나는 시점과 최대의 효과가 나타나는 시점을 알아보기 위해 연구를 진행한 결과 복용 후 40분에 효과가 나타나기 시작하고, 1시간이내에 최대의 효과를 나타내며 심박동수를 저하시키는 것을 알 수 있었다. 또한 심박동수의 최대치와 최소치의 차이값, 즉 심박동수 변동폭의 범위가 작아지는 양상을 보였다. CCTA검사에 있어 이바브라딘의 활용은 보다 안전하게 심박동수를 낮춰 프로토콜의 선택을 용이하게 할 뿐만 아니라 영상획득구간에 대한 적정범위를 줄임으로써 환자의 피폭선량을 최소화하고 영상의 품질을 높일 수 있다고 사료된다. Hearts vulnerable to movement are difficult to image during the CCTA test, and the patient s respiration and heart rate are factors that determine the quality of the image. Proceeding a cardiac CT examination by properly controlling the heart rate means that the optimal image can be obtained without significant changes in the thickness and location of the cardiovascular vessels that vary depending on the heart rate. If a drug that controls heart rate is administered to patients with high heart rate, the examination for optimal image acquisition becomes easier. As a result of conducting a study to determine when the effect of lowering the heart rate by taking ivabradine and when the maximum effect appeared, the effect began to appear 40 minutes after taking it, and the heart rate decreased to a maximum within 1 hour. In addition, the difference between the maximum and minimum heart rate values, that is, the range of the heart rate fluctuation has been reduced. The utilization of ibabradine in CCTA examination not only facilitates protocol selection but also reduces the appropriate range for image acquisition intervals, minimizing patient exposure dose and improving image quality.
박경현,변영태,김명욱,김선호,최상삼,조욱래,박승한,김웅,Park, K. H.,Byun, Y. T.,Kim, M. W.,Kim, S. H.,Choi, S. S.,Cho, W. R.,Park, S. H.,Kim. U. 한국광학회 1997 한국광학회지 Vol.8 No.2
가로.세로의 비가 큰 광도파로 소자 제작용 마스크 제작에는 레이저 리소그래피 장치가 기존의 리소그래피 장치에 비해 비용면 등을 고려하면 많은 장점을 가지고 있다. 레이저 리소그래피 장치를 이용 보편적인 양극형 마스크는 물론 기존의 레이저 리소그래피 장치로는 제작하기에 많은 어려움이 있는 음극형 마스크를 포토레지스트의 인위적 변화를 이용 제작할 수 있었다. 제안된 방법은 주변환경 즉 먼지, 장치의 진동 그리고 레이저 입사광 변화 등에 기존의 장치 보다 덜 민감함을 실험적으로 확인하였다. 이 방법을 이용 광도파로 소자의 기본을 이루는 S형태 곡선으로 구성된 광분배기 패턴을 제작하였으며, 제작된 패턴의 대비 및 재현성에 있어서 그 특성이 매우 우수함을 실험적으로 확인하였다. Most conventional lithography systems have been oriented to fabricate electronic devices. Therefore, it is not so easy to fabricate large aspect ratios of waveguide patterns with those systems. When considering costs and efficiencies, a laser lithography system provides number of benefit in realizing waveguide patterns. However, because the conventional laser lithography system could make only positive tone masks, it is inconvenient in determining the direction of the waveguide. A simple and reliable technique to produce negative tone masks was developed by using the laser beam writing. This technique was not sensitive to environmental situations such as dust, vibration, intensity variation. Making use of the technique a variety of device patterns such as Y-branch, directional coupler, and highly smooth S-shape bend could be successfully fabricated with a good contrast.
UV Laser Rayleigh Scattering을 이용한 C₃H_8/O₂ 화염에서 가스 성분의 농도 및 온도 분포 계측에 관한 실험적 연구
진성호(S. H. Jin),남기중(G. J. Nam),김회산(H. S. Kim),장래각(N. K. Chang),박승한(S. H. Park),김웅(U. Kim),박경석(K. S. Park),김경수(G. S. Kim) 한국자동차공학회 1997 한국 자동차공학회논문집 Vol.5 No.2
Rayleigh Scattering Cross Sections(σ_i)of various gases and the temperature distributions of premixed C3HJOz flame are measured by high power KrF(248nm) Excimer laser and ICCD cam-era. Results show that σ_i of 0₂, and Propane(C₃H_8) gases agree well in the 5% error range, but σ_i of H ₂ has the more or less difference from the calculated value by other groups. This is attributed to the low RS signal of H ₂ to Nosie level(S/N ratio).<br/> The temperature distributions of flame range out between 300K in the air and about 2000K in the burned area. In this temperature range, our system has the about 250K temperature resolution. Because low RS signals in the reaction area with high temperatue are affected highly by noises, temperature uncertainty of this area is relatively high to another part of flame.<br/> Experimental results show that UV Rayleigh Scattering can be used for the measurement of mixing ratio of mixed gases and the temperature distributions of flame. Especially, this technique can be applied for the measurement of the mixing ratio of air/fuel before the ignition and the flame structure after the ignition inside the Engine.<br/>
CO₂ 레이저 광의 조사조건에 따른 치아의 치수강내 온도상승에 관한 연구
고동섭(D.S. Ko),박용환(Y.H. Bak),신상훈(S.H. Shin),엄효순(H.S. Eom),김웅(U. Kim),이찬영(C.Y. Lee) 한국광학회 1990 한국광학회지 Vol.1 No.2
본 연구에서는 레이저와 치아조직과의 상호작용에 대한 연구의 일환으로, CO₂ 레이저의 발진파장인 10.6㎛의 레이저 빔 조사시에 일어나는 치아의 온도변화를 조사하기 위하여 CO₂ 레이저 발진장치를 제작하여 여러 가지 조사에너지, 조사시간에 대하여 발거된 치아의 치수강의 온도변화를 측정 분석하였다. 측정한 data를 분석하여 최대 상승온도 ΔTm를 추정할 수 있는 다음과 같은 실용적인 경험식을 얻었다.<br/> ΔTm=αPΔτexp(-βd)<br/> 여기서 P는 레이저의 출력(W)이고 Δτ는 조사시간(sec), d는 치아의 두께(㎜)이다. This study was performed to obtain fundamental data on temperature increases in the dental tissues irradiated by 10.6㎛ laser radiation. For this purpose a experimental facility was established, which was composed of a CO₂ laser, a shutter unit and a temperature sensing device. The temperature changes in the pulp chamber of extracted molars, during and after the laser irradiation, were measured as function of laser power, the time of irradration and the thickness of the sample. An empirical formula for the maximum temperature increases. ΔTm was derived from the measured data as follows;<br/> ΔTm=90PΔτ exp(-1.5d)<br/> where P. Δτ rand d are the laser power(W), irradiation time(sec) and the thickness(㎜) between pulp chamber and occlusal surface, respectively.<br/> Also a theoretical calculation model based on simplified assumptions were established and the results from the calculation were compared with the measured temperature data. A fairly good agreement was obtained.
레이저에 의한 Cr 표면합금층 형성에 미치는 Cr 첨가방법의 영향
김도훈,김웅,김경배 대한금속재료학회(대한금속학회) 1985 대한금속·재료학회지 Vol.23 No.8
The methods of Cr-addition on a low-C steel affect the properties and the formation of a Cr-surface-alloyed layer produced by CO₂laser. The depth of melted zone showed larger in a Cr-electroplated specimen than in a Cr-powder coated one, while the width of melted zone on surface showed reversed results. The hardness of surface alloyed zone in a Cr-electroplated specimen resulted lower than that of matrix as other investigators had reported. Meanwhile that in a Cr-powder coated specimen increased very high due to some precipitations and the phase transformation. There is a tendency in the Cr-powder coated specimen for Cr to be penetrated and dispersed in melted region deeply compared with in Cr-electroplated specimen. In order to enhance the wear resistance on the Cr-surface-alloyed zone by laser, it is desirable to use the method of Cr-powder coating on low-C steel.