퍼지 제어기를 이용한 SRM 속도 제어

박희성,성세진,이흥호 충남대학교 공업교육연구소 1998 論文集 Vol.21 No.1

In this paper, the fuzzy control logic of Switched Reluctance Motor(SRM) is introduced to apply the variable speed drive system. SRM has similar characteristics to a DC motor, its speed variation rate is high to the changes of torque. Therefore, an optimal control method is needed for covering this weakness. As a control technique, the conventional PI control, which has the advantage like simplicity and stability, has been applied in many application. But the PI controller is very difficult to obtain robust characteristic for parameter variation and disturbance. To solve this problem the fuzzy logic controller used in addition to the conventional PI controller result in the speed response characteristic is improved.

로케트 工學에 관한 硏究 : 第1報 : 亞音速 亂流流動에서 飛行翼模型의 剝離現象 Ⅰst Report : Separation of Airfoils in Subsonic Turbulent Flow

朴煥奎,金鍾一,金鎭興,李茂錫,朴吉文,鄭洛奎,李行男,李東起 조선대학교 동력자원연구소 1984 動力資源硏究所誌 Vol.6 No.2

Separation, pressure and velocity distributions were studied fully developed two dimensinonal, incompressible flow over a flat airfoil in subsonic wind tunnel. Velocity and turbulence were measured with a two channel constant temperature hot wire anemometer and pressure with a pitot tube and pressure tranducer system. The experimental results were obtained as follow: (1) Turbulent intensity of shear layer just outside the separation point is considered to affect the size of separation bubble. (2) Static pressure coefficient is separated into three regions according to its value change. (3) Separation point is varied with the change of attack angle. (4) Velocity distributions and boundary layers normal to airfoil surface are changed as variation of attack angle of airfoil.

법랑모세포 분화와 법랑질 형성과정에서 OD314, Apin protein의 발현 및 기능

박종태,최용석,김흥중,정문진,오현주,신인철,박주철,손호현 대한치과보존학회 2006 Restorative Dentistry & Endodontics Vol.31 No.6

본 연구에서는 법랑모세포 분화와 법랑질 형성에 연관이 있는 OD314 일명 Apin protein의 기능을 밝힐 목적으로, in-situ hybridization에 의한 OD314 mRNA 발현과 법랑모세포 세포주에서 OD314 enamel matrix protein의 발현, 그리고 OD314 유전자를 과발현/억제시킬 수 있는 construct를 제작한 후 법랑질 형성 중에 OD314의 기능을 알아보고자 RT-PCR를 시행하여 다음과 같은 결과를 얻었다. 1. OD314 mRNA는 발생중인 상아모세포보다 법랑모세포에서 강하게 발현되었다. 2. Tuftelin은 석회화 결정이 형성되는 14일까지 발현이 지속되고, 그 이후부터 점차 감소하였다. Amelogenin과enamelin은 7일부터 그 발현이 점점 감소하였다. 3. U6-OD314 siRNA construct를 이용하여 transfection한 법랑모세포 세포주는 OD314와 tuftelin,MMP2 mRNA 발현이 감소하였으며, CM-OD314를 transfection하여 OD314의 과발현을 유도한 경우에는 OD314와 MMP20 mRNA의 발현이 뚜렷이 증대되었다. 이 결과는 OD314가 법랑모세포의 분화와 법랑질의 형성 그리고 석회화 과정에 중요한 역할을 하는 새로운 인자임을 시사한다. This study was aimed to elucidate the biological function of OD314 (Apin protein), which is related to ameloblast differentiation and amelogenesis. Apin protein, calcifying epithelial odontogenic (pindborg) tumors (CEOTs)-associated amyloid, were isolated from CEOTs, and has similar nucleotide sequences to OD314. We examined expression of the OD314 mRNA using in-situ hybridization during tooth development in mice. Expression of OD314 and several enamel matrix proteins were examined in the cultured ameloblast cell line up to 28 days by reverse transcription-polymerase chain reaction (RT-PCR) amplification. After inactivation and over-expression of the OD314 gene in ameloblast cell lines using U6 vector-driven RNA interference and CMV-OD314 construct, RT-PCR were performed to evaluate the effect of the OD314 during amelogenesis. The results were as follows: 1. In in-situ hybridization, OD314 mRNAs were more strongly expressed in ameloblast than odontoblast. 2. When ameloblast cells were cultured in the differentiation and mineralization medium for 28 days, the tuftelin mRNA expression was maintained from the beginning to day 14, and then gradually decreased to day 28. The expressions of amelogenin and enamelin were gradually decreased according to the ameloblast differentiation. 3. Inactivation of OD314 by U6-OD314 siRNA construct down-regulated the expression of OD314, MMP-20, and tuftelin, whereas over-expression of OD314 by CMV-OD314 construct up-regulated the expression of OD314 and MMP-20 without change in tuftelin. These results suggest that OD314 is considered as an ameloblast-enriched gene and may play the important roles in ameloblast differentiation and mineralization.

법랑모세포 분화와 성숙과정에서 OD314의 발현

박주철,안성민,김흥중,정문진,박민주,신인철,손호현 大韓齒科保存學會 2005 Restorative Dentistry & Endodontics Vol.30 No.5

법랑모세포는 법랑질을 형성하고 유지하는 세포로, 법랑질의 유기기질을 분비하고 법랑질 석회화 과정에도 관여한다. 치아 발생과정에서 법랑모세포의 분화는 순차적인 상피-간엽 상호작용에 의하여 조절되나, 분화나 성숙과정의 정확한 기전은 아직까지 잘 알려져 있지 않다. 최근에 상아모세포에서 처음 발견된 OD314가 치아 발생과정에서 상아질을 형성하는 상아모세포 뿐 아니라 법랑모세포에도 발현된다고 하였다. 이에 본 연구에서는 생쥐 하악 전치의 다양한 시기의 법랑모세포를 이용하여, 형태학적 분석과 in-situ hybridization에 의한 OD314 mRNA의 발현 그리고 OD314 항체를 이용한 면역조직화학적 분석을 통하여 OD314 유전자의 법랑 모세포 분화와 성숙과정에서의 역할을 연구하여 다음과 같은 결과를 얻었다. 1. 형태학적으로 법랑모세포는 분화 단계에 따라 분비 전단계 법랑모세포, 분비기 법랑모세포, 성숙기의 평탄끝 법랑모세포와 성숙기의 주름끝 법랑모세포로 구분되었다. 2. OD314 mRNA는 분비기의 법랑모세포에서부터 발현되기 시작하여 법랑모세포가 성숙해갈 수록 그 발현이 증가하였다. 3. OD314 단백질은 분비 전단계의 법랑모세포에서는 발현되지 않고, 분비기의 법랑모세포에서는 세포질에 전체적으로 발현되었다. 성숙기의 평탄끝 법랑모세포와 주름끝 법랑모세포에서는 세포의 근심과 원심끝단에 OD314 단백질이 강하게 발현되었다. 이상의 결과를 종합하여 OD314는 법랑모세포의 분화와 성숙과정에서 세포질 내부에서 특징적인 역할을 하는 것으로 사료된다. Ameloblasts are responsible for the formation and maintenance of enamel which is an epithelially derived protective covering for teeth. Ameloblast differentiation is controlled by sequential epithelial-mesenchymal interactions. However, little is known about the differentiation and maturation mechanisms. OD314 was firstly identifled from odontoblasts by subtraction between odontoblast/pulp cells and osteoblast/dental papilla cells, even though OD314 protein was also expressed in ameloblast during tooth formation. In this study, to better understand the biologcal function of OD314 during amelogenesis, we examined expression of the OD314 mRNA and protein in various stages of ameloblast differentiation using in-situ hybridization and immunohistochemistry. The results were as follows : 1. The ameloblast showed 4 main morphological and functional stages referred to as the presecretory, secretory, smooth-ended, and ruffle-ended. 2. ○D314 mRNA was expressed in secretory ameloblast and increased according to the maturation of the cells. 3. OD314 protein was not expressed in presecretory ameloblast but expressed in secretory ameloblast and maturative ameloblast. OD314 protein was distributed in entire cytoplasm of secretory ameloblast. However, OD314 was localized at the proxiamal and distal portion of the cytoplasm of smooth- ended and ruffle-ended ameloblast. These results suggest that ○D314 may play important roles in the ameloblast differentiation and maturation.

성균관대학교 물리학과 방음실의 설계 및 제작

朴興秀,尹錫旺,李聖壽,朴光俊,吳世珍 성균관대학교 기초과학연구소 1986 論文集 Vol.37 No.1

An anechoic chamber was constructed to make to condition of acoustic free field at the Department of Physics, Sung Kyun Kwan University. In this paper the criteria for the design and construction of the anechoic chamber are described. 48cm long wedges of density 15.3kg/㎥ glasswool attached to the 40×20×20㎤ base were used for the lining of anechoic chamber with the cutoff frequency of 125Hz. The interior space of the chamber is 3.56m long, 3.38m wide and 2.37m high.

에탄올이 첨가된 TMA포접화합물의 냉각특성

김진홍,정낙규,김창오,박호진 조선대학교 에너지.자원신기술연구소 2002 에너지·자원신기술연구소 논문지 Vol.24 No.2

The purpose of this study is to investigate the propriety of TMA clathrate as a cold storage medium. Particularly, this is to examine the extent of subcooling improvement when the additives are added to the TMA clathrate, because water used cold storage material has low phase change temperature and subcooling. This study has been analyzed and compared with TMA 30 wt% clathrate how phase change temperature, subcooling and specific heat in the various concentrations are changed. This results view to be improved phase change temperature and subcooling of TMA 30wt% as a cold storage medium, when it had some additive. Additionally, it is found that the additive must be controlled under available solution limit and study for new additive must be lasted to know its effect.

2003년 국내 중증급성호흡기증후군 진료 현황 및 문제점 분석

이진수,김은실,정문현,백제중,정선화,안주희,최영화,이선희,고철우,김성범,김민자,박승철,기현균,송재훈,최상호,김양수,이상오,조용균,박영훈,정숙인,김연숙,이흥범,손창희,장성희,정희진,김우주 대한감염학회 2004 감염과 화학요법 Vol.36 No.3

목적 : 2002년 말 중국에서 SARS가 발생한 이후 국내에서도 2003년 10월까지 총 3명의 추정환자, 17명의 의심환자가 보고되었다. 향후 추가적인 SARS의 유행이 우려되는 상황에서, 그간의 SARS 환자 진료에 있어서의 실질적인 준비사항, 진료 현황 등에 대한 조사를 통해 문제점을 파악하여, 향후 더 나은 대비가 될 수 있도록 개선점을 제시하고자 하였다. 재료 및 방법 : SARS로 의심되는 환자를 진료 경험이 있는 병원의료진을 대상으로 2003년 10월에 설문조사를 실시하였다. 설문에는 SARS 환자 진료 시의 실질적인 조치, 진료 현황, 병실, 응급실 및 외래에서의 격리 시설과 준비사항, 보건당국의 관리와 지원에 관한 사항을 포함하였다. 결과 : 대상이 되는 22개 병원 중 17개(17/22, 77.2%) 병원이 설문에 응하였다. SARS 환자를 위한 격리실은 응급실, 외래, 일반병실 및 중환자실에서 각각 9개(9/17, 52.9%), 5개(5/17, 29.4%), 15개(15/16, 93.7%), 4개(4/16, 25%) 병원에서 음압처리가 되어있지 않은 일인실 혹은 다인실이 사용되었고, 1개(1/16, 6.3%) 병원에서만 일반병실에서 음압격리실이 운영되었다. 입원환자의 진찰 시 개인보호구의 착용은 거의 모든 의료기관에서 이루어졌다. 보건당국에서 SARS지정병원의 시설 등을 사전에 확인한 곳은 1곳(1/12, 8.3%)이였고, 14개 병원(14/15, 93.3%)에서는 보건당국에 의뢰한 검사결과를 통하 받지 못하였다. 결론 : 의료기관에서 SARS 환자용 격리실뿐만 아니라 기존의 격리실 설비 등이 미흡하였으며, 특히 중환자실 및 외래의 준비가 더욱 부족하였다. 보건당국의 의료기관에 대한 종합적인 지원이 부족하였고, 병원과의 원활한 연계가 잘 이루어지지 않았다. SARS 만이 아닌 격리를 필요로 하는 질환의 적절한 진료를 위해 향후 병원 시설의 정비와 정부차원에서의 보다 구체적이고 실질적인 대책마련이 필요하다. Background : There was an worldwide outbreak of the Severe Acute Respiratory Syndrome (SARS) originated from China in late 2002. During that period three cases of suspected SARS and 17 cases of probable SARS were reported in Korea. With the concerns about the reemergence of SARS-coV transmission, it is important to be prepared for any possibility. So, this study is aimed to analysis the past measures in managing SARS and propose the amendatory plans to improve the preparedness. Materials & Methods : Questionnaires were collected among clinicians with any experience in managing the probable or suspected SARS cases in Oct. 2003. 17 out of 22 hospitals responded to the questionnaire. The contents in the questionnaire were practical activities, personal equipments, response plans, isolation facilities in emergency centers, outpatient clinics, general wards and intensive care units, and relationship with the public health department. Results : The dedicated isolation rooms in emergency centers, outpatient clinics, general wards, and intensive care units were prepared in 9 (9/17, 52.9%), 5 (5/17, 29.4%), 15 (15/16, 93.7%), and 4 (4/16, 25.0%) hospitals, respectively. Except for one hospital that newly made negative pressure room for SARS, single or multi-bed rooms without airborne infection control were used in all the other hospitals. The personal precaution principles were kept quite well in general wards. Before the designation of SARS hospital by the public health department prior evalution to see if the hospital was suitable for managing SARS was conducted in only 1 (1/12, 8.3%) hospital. The results of laboratory diagnosis were reported back in 1 (1/15, 6.6%) hospital. Conclusions : The isolation facilities which can control airborne infection were almost deficient not only for SARS but also for other respiratory transmissible diseases. For the infection control of transmissible diseases including SARS, more investment is needed on medical facilities and comprehensive support from the public health department required.

Camphoroquinone이 복합레진의 특성에 미치는 영향

탁흥수,박상진 대한치과보존학회 2001 Restorative Dentistry & Endodontics Vol.26 No.1

The purpose of this study was to examine the influences of camphoroquinone on the properties of five experimental composites. The contents of camphoroquinone were varied as 0.2%, 0.3%, 0.4%, 0.5%, and 0.6%, with silanized filler 75% and tertiary amine 0.2%. Five kinds of experimental composites were prepared, and diametral tensile strength, shear bond strength, depth of cure and yellowish discoloration were tested as a measurement. Specimen number of 10 were applied to all test items and experimental groups. Specimens for testing the diametral tensile strengths with internal diameter of 6mm in diameter and 3mm in height were filled with 5 experimental composites which were crushed with 1mm/min cross-head speed on Instron universal testing machine (Model No. 4467). Shear bond strength was measured on specimens attached to bovine teeth enamel etched with 37% phosphoric acid. Depth of cure was measured by the measurement of height of specimens which were removed the un-polymerized portion with acetone. Yellowness measurements were made by chromometer(Minolta Co. Japan)using L*a*b* values. ANOVA and Multiple range tests were used analyzed data with confidence level at 95%. The mean value of the shear bond strengths ranged from 31.03Mpa to 39.49Mpa. Following results were obtained: 1.Diametral tensile strength was highest in experimental group 3, then was not affected by the contents of camphoroquinone (r²=0.0422). 2.Composite resins contationing 0.4% camphoroquinone showed the highest shear bond strength, but there was no statistical significance (p=0.3718). 3.Camphoroquionone reduces the depth of cure in the composite resins (p=0.0004, r²=0.9483). 4.Camphoroquinone made the composites yellowish (r=²0.9815). These results mean that increased content of camphoroquinone reduces the depth of cure, and that camphoroquinone make composites yellowish.

XML기반 전자상거래 프레임워크 기술

한흥구,박진석,윤순영,최성 호서대학교 반도체제조장비국산화연구센터 2001 반도체장비학술심포지움 Vol.2001 No.-

자동차 차체조립공정설계를 위한 시뮬레이션

황흥석,박태원,조규성,유진식 한국경영과학회 2000 한국경영과학회 학술대회논문집 Vol.- No.1

본 연구에서는 자동차의 차체조립공정설계를 위하여 FACTOR/AIM 및 자체 개발한 생산시스템 성능평가를 위한 시뮬레이션 프로그램을 이용하여 비교 연구하였다. 이를 위하여 먼저 자체에서 개발한 시스템성능 산정 방법으로 초기 해를 구하고 세부 생산라인의 고장 Data와 조립라인의 구성, 운반장비 등의 의 다양한 여건을 고려하기 위하여 FACTOR/AIM을 사용하였다. Data의 분석을 위하여 ExpertFit를 사용하였으며 초기 시스템 모델링 및 Data로 부터 목표 생산시스템을 만족하는 시스템을 단계별로 찾아가는 과정을 사용하여 최적 해를 구하였다. 본 연구에서 분석한 K회사의 경우 목표 생산량 70대/시간을 만족하기 위하여 4 차의 개선을 통하여 71.57대/시간의 생산라인을 구하였다. 본 연구에서 생산조립라인의 공정설계를 위한 시뮬레이션 과정을 실 예를 들어 제시하였으며 다른 제품의 생산공정분서에도 활용 가능하리라 생각된다.