http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Jia-Xiang Lin,Yong-Jian Cai,Ze-Ming Yang,Shu-Hua Xiao,Zhan-Biao Chen 국제구조공학회 2022 Steel and Composite Structures, An International J Vol.45 No.1
Steel fiber composite bar (SFCB) is a novel type of reinforcement, which has good ductility and durability performance. Due to the unique pseudo strain hardening tensile behavior of SFCB, different flexural behavior is expected of SFCB reinforced concrete (SFCB-RC) beams from traditional steel bar reinforced concrete (S-RC) beams and FRP bar reinforced concrete (F-RC) beams. To investigate the flexural behavior of SFCB-RC beam, four points bending tests were carried out and different flexural behaviors between S/F/SFCB-RC beams were discussed. An flexural analytical model of SFCB-RC beams is proposed and proved by the current and existing experimental results. Based on the proposed model, the influence of the fiber volume ratio R of the SFCB on the flexural behavior of SFCB-RC beams is discussed. The results show that the proposed model is effective for all S/F/SFCB-RC flexural members. Fiber volume ratio R is a key parameter affecting the flexural behavior of SFCB-RC. By controlling the fiber volume ratio of SFCB reinforcements, the flexural behavior of the SFCB-RC flexural members such as bearing capacity, bending stiffness, ductility and repairability of SFCB-RC structures can be designed.
Xiang-Feng Wu,Yi-Jin Wang,Zuo-Lin Cao,Yan-Mei Feng,Hui Li,Chen-Xu Zhang,Jun-Zhang Su,Jia-Rui Zhang,Yi-Wei Wang,Kai-Yuan Wang,Guo-Wen Sun 대한화학회 2018 Bulletin of the Korean Chemical Society Vol.39 No.7
The novel AgCl/Ag2SO3 hybrids as an efficient photocatalyst had been fabricated by an in situ synthetic method. The correlations between the structure and the photocatalytic properties of the as-fabricated hybrids were analyzed. Experimental results exhibited that with increasing the amount of Ag2SO3, the degradation rate of the as-obtained samples was firstly increased and then decreased under the visible light irradiation. When the mass ratio of AgCl to Ag2SO3 was 1:2, in 30?min, it displayed the highest degradation rate of 99.2% for rhodamine-B, which was obviously higher than 46.1, 60.5, and 14.6% of pure AgCl, Ag2SO3, and TiO2 (P25), respectively. Similar results could be found in degradation of methyl orange. It had the maximum of 97.4% in 90?min, which was higher than 55.2, 48.7, and 12.7% of pure AgCl, Ag2SO3, and P25, respectively. Moreover, the as-prepared hybrids possessed the enhanced separation and transfer of photo-generated electron?hole pairs compared to the pure samples. In addition, the holes and superoxide radicals played the dominant role and the hydroxyl radicals played the secondary role during the process of photocatalytic degradation.
Knockout of the EgriBLOS2 gene results in the transparent integuments of Ectropis grisescens larvae
Li Jia-Li,Zhuang Xiang-Lin,Yuan Ting-Ting,Cai Xiao-Ming,Luo Zong-Xiu,Bian Lei,Chen Zong-Mao,Li Zhao-Qun,Liu Nai-Yong 한국응용곤충학회 2022 Journal of Asia-Pacific Entomology Vol.25 No.1
The body colors of insects have evolved specialized roles in body protection, signaling and physiology. In some case, the larvae can camouflage their body colors to adapt the habitants and protect themselves. However, the genetic and molecular basis on larval body colors of the tea geometrid, Ectropis grisescens, remains poorly known. Here, we reported an effect of the lysosome-related organelles complex-1, subunit 2 (EgriBLOS2) gene knockout on larval integuments of E. grisescens, by using a clustered regularly interspaced short palindromic repeat (CRISPR)/CRISPR-associated protein 9 (Cas9) system. Combining transcriptomic data and PCR approaches, we first identified the EgriBLOS2 gene from E. grisescens, which encoded 137 amino acids and comprised 3 introns. In the phylogenetic analysis, EgriBLOS2 clustered in the Lepidoptera clade with high conservation to members in other lepidopteran species. Developmental expression profiles revealed that EgriBLOS2 was constantly tran scribed at each stage, in which its expression was significantly lower in 2nd instar larvae than that of other instars. After injecting EgriBLOS2-specific guide RNA and Cas9 messenger RNA into eggs, 70% of larvae showed the translucent integuments in G0 generation, with an emphasis on black splayed patterns in the 2nd and 8th segments of abdomens. However, some typical characteristics of larvae were not obviously changed in mutant instars, such as ocelli, mouthparts and other appendants. This study has unraveled the roles of EgriBLOS2 in the formation of larval integument colors, and provides an alternative strategy for pest management based on the colors in this species.
Peng Han,Jia Lin,Wen Wang,Zhihao Liu,Yating Xiang,Ting Zhang,Qiang Liu,Xiaohu Guan,Ke Qiao,Yingchun Xie,Kuaishe Wang 대한금속ᆞ재료학회 2023 METALS AND MATERIALS International Vol.29 No.2
The high-entropy alloy particles reinforced 6061Al composite was prepared by cold spray (CS) and then modified by frictionstir processing (FSP). The microstructure evolutions, corrosion, and wear behaviors of the composites were investigated. Results showed that numerous micro-pores and cracks were distributed in the Al matrix due to adiabatic shear instability andinsufficient deformation of the deposited particles for CSed samples. The average size of uniformly distributed HEA particleswas ~ 24 μm, and the geometric necessary dislocation (GND) density reached 17.1 × 1015m−2 due to large plastic deformationduring CS. Comparatively, the micro-pores and cracks were eliminated, and many fragmented HEA particles dispersed inthe Al matrix with an average size of ~ 4 μm for FSPed sample. Note that the GND density reduced to 9.8 × 1015m−2 due todynamic recrystallization during FSP. The formation rate of the oxide film was gradually greater than that of the dissolutionrate with the samples immersion in 3.5 wt% NaCl solution from 12 to 36 h, and the main corrosion mechanism was particledissolution around micro-pores and pitting for CSed and FSPed samples, respectively. In the polarization process, the FSPedsamples exhibited low corrosion tendency and high corrosion rate due to the dense and uniform microstructure, low GNDdensity, and dispersed HEA particles. The FSPed samples had better wear resistance than the CSed samples at 25 °C and200 °C. The dominant wear mechanisms of CSed and FSPed samples were abrasion at 25 °C, while the wear mechanismsof these samples were adhesion accompanied by abrasion at 200 °C.
Peng Han,Jia Lin,Wen Wang,Zhihao Liu,Yating Xiang,Ting Zhang,Qiang Liu,Xiaohu Guan,Ke Qiao,Yingchun Xie,Kuaishe Wang 대한금속·재료학회 2023 METALS AND MATERIALS International Vol.29 No.3
The high-entropy alloy particles reinforced 6061Al composite was prepared by cold spray (CS) and then modified by frictionstir processing (FSP). The microstructure evolutions, corrosion, and wear behaviors of the composites were investigated. Results showed that numerous micro-pores and cracks were distributed in the Al matrix due to adiabatic shear instability andinsufficient deformation of the deposited particles for CSed samples. The average size of uniformly distributed HEA particleswas ~ 24 μm, and the geometric necessary dislocation (GND) density reached 17.1 × 1015m−2 due to large plastic deformationduring CS. Comparatively, the micro-pores and cracks were eliminated, and many fragmented HEA particles dispersed inthe Al matrix with an average size of ~ 4 μm for FSPed sample. Note that the GND density reduced to 9.8 × 1015m−2 due todynamic recrystallization during FSP. The formation rate of the oxide film was gradually greater than that of the dissolutionrate with the samples immersion in 3.5 wt% NaCl solution from 12 to 36 h, and the main corrosion mechanism was particledissolution around micro-pores and pitting for CSed and FSPed samples, respectively. In the polarization process, the FSPedsamples exhibited low corrosion tendency and high corrosion rate due to the dense and uniform microstructure, low GNDdensity, and dispersed HEA particles. The FSPed samples had better wear resistance than the CSed samples at 25 °C and200 °C. The dominant wear mechanisms of CSed and FSPed samples were abrasion at 25 °C, while the wear mechanismsof these samples were adhesion accompanied by abrasion at 200 °C.
Construction and Cloning of the Rc/CMV-GFP Fluorescence Expression Vector
Wang, Yi-Xiang,Li, Sheng-lin,Fu, Jia,Zhang, Kui-hua Korean Academy of Oral Biology and the UCLA Dental 2000 International Journal of Oral Biology Vol.25 No.1
A plasmid that can express fluorescence in prokaryotic and eukaryotic cells, RC/CMV-GFP was constructed by cloning the green fluorescent protein gene〔gfp〕into the Rc/CMV expression vector. The green fluorescent protein 〔GFP〕was expressed in E. coli JM109〔Rc/CMV-FGP〕, and green light was emitted under UV irradiation. Thus, this vector can be used to label oral microorganisms or tumor cells for studies of their biological behavior.
Ying Qiao,Zong-Xiang Lu,Ji Lu,Jia-Yang Ruan,Lin-lin Wu 대한전기학회 2015 Journal of Electrical Engineering & Technology Vol.10 No.6
The integration of the large-scale wind power brings great challenge to the stability of the power grid. This paper investigates and studies the fault on May 14, 2012 of the large-scale cascading trip-off of wind turbines in North China. According to the characteristics of the voltage variation, the fault process is divided into three stages: the pre-event stage, the critical stage before cascading, and the cascading stage. The scenes in the fault are reproduced, using the full-size actual power system model. Simulation models of double-fed induction generators (DFIGs) and SVCs including protection settings and controller strategies are carefully chosen to find out the reason of voltage instability in each stage. Some voltage dynamic that have never been observed before in the faults of the same kind are analyzed in detail, and an equivalent voltage sensitive dynamic model of DFIG is proposed for the fast computation. The conclusions about the voltage dynamics are validated by the actual PMU observation evidence.
Qiao, Ying,Lu, Zong-Xiang,Lu, Ji,Ruan, Jia-Yang,Wu, Lin-lin The Korean Institute of Electrical Engineers 2015 Journal of Electrical Engineering & Technology Vol.10 No.6
The integration of the large-scale wind power brings great challenge to the stability of the power grid. This paper investigates and studies the fault on May 14, 2012 of the large-scale cascading trip-off of wind turbines in North China. According to the characteristics of the voltage variation, the fault process is divided into three stages: the pre-event stage, the critical stage before cascading, and the cascading stage. The scenes in the fault are reproduced, using the full-size actual power system model. Simulation models of double-fed induction generators (DFIGs) and SVCs including protection settings and controller strategies are carefully chosen to find out the reason of voltage instability in each stage. Some voltage dynamic that have never been observed before in the faults of the same kind are analyzed in detail, and an equivalent voltage sensitive dynamic model of DFIG is proposed for the fast computation. The conclusions about the voltage dynamics are validated by the actual PMU observation evidence.
A facile macroporous resin-based method for separation of yellow and orange Monascus pigments
Suo Chen,Dong-Xiao Su,Meng-Xiang Gao,Jia-Lan Zhang,Ying-Bao Liu,Qing-Hua Wu,Hua-Lin Yang,Li Li 한국식품과학회 2021 Food Science and Biotechnology Vol.30 No.4
The yellow Monascus pigments (YMPs) namedmonascin and ankaflavin and the orange Monascus pigments(OMPs) named rubropunctatin and monascorubrinare two groups of bioactive components in a mixture statein the Monascus fermented products. In order to separatethese two groups of bioactive pigments, a facile macroporousresin-based method was developed. The weak-polarresin CAD-40 was selected from the seven tested macroporousresins as it revealed better properties for theadsorption and desorption of the YMPs and OMPs. Then,CAD-40 resin was used for column-chromatographicseparation. After eluted by 4 bed volumes of ethanol, theyellow group (monascin and ankaflavin) and the orangegroup (rubropunctatin and monascorubrin) were successfullyseparated and purified, with an increased content from49.3% and 44.2% in the crude pigment extract to 85.2%and 83.0% in the final products, respectively. This methodwould be helpful for the large-scale separation and purificationof Monascus pigment products with specificbioactivity.