http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Hong Chan Ma,Damisih,Maryane Putri,Jong Hoon Cheon,김재홍,이희영 한국물리학회 2012 THE JOURNAL OF THE KOREAN PHYSICAL SOCIETY Vol.61 No.12
Indium-saving transparent conductive oxide (TCO) thin films, <i>i.e.</i>, zinc and tin co-doped indium oxide (IZTO) films, were investigated for dye-sensitized solar cell (DSSC) applications. The films were prepared by the radio-frequency (RF) magnetron sputtering method utilizing a ceramic target with a nominal composition equal to In<sub>0.6</sub>Zn<sub>0.2</sub>Sn<sub>0.2</sub>O<sub>1.5</sub>. The substrate temperature was changed from room temperature to 400 ℃ while the RF power and the argon gas pressure during deposition were kept constant. The photovoltaic conversion efficiencies of the DSSC samples made with IZTO electrodes were compared with the samples made with FTO electrodes. Values of approximately 6.81% and 4.74% were obtained for the DSSC samples with FTO and IZTO electrodes, respectively, when the firing process was carried out in air atmosphere during DSSC fabrication. However, with the addition of post-annealing in argon or a forming gas, efficiency values increased to 6.06% or 5.54%, respectively, for the DSSC sample with an IZTO electrode.
Ma, Kyoung Tak,Yang, Jong Yun,Kim, Ji Hyun,Kim, Na Rae,Hong, Samin,Lee, Eun Suk,Seong, Gong Je,Kim, Chan Yun Lippincott Williams Wilkins, Inc. 2012 Journal of glaucoma Vol.21 No.5
PURPOSE: To investigate the surgical results of Ahmed valve implantation with intraoperative bevacizumab injection in patients with neovascular glaucoma (NVG). METHODS: A retrospective comparative case series review was conducted on 52 eyes with NVG who underwent Ahmed glaucoma valve implantation with or without intraoperative bevacizumab intravitreal injection. In the intraoperative intravitreous bevacizumab injection group (IVB group, 20 eyes), 1.25 mg of bevacizumab was injected into the vitreous cavity during Ahmed valve implantation. In the control group (32 eyes), only Ahmed valve implantation was performed. Surgical failure was defined when (1) the postoperative intraocular pressure was over 21 mm Hg at consecutive clinic visits, (2) the visual acuity became light perception negative, (3) additional antiglaucomatic surgery was required, or (4) devastating operative or postoperative complications were noted. RESULTS: Although the success rate in the IVB group (70.0%) was higher than that in the control group (62.5%) 1 year after operation, the differences were not statistically significant (P=0.828 by log-rank test). Mean intraocular pressures in the IVB group were significantly lower than those of the control group at 12 and 15 months (P<0.05 by the Mann-Whitney U test). Postoperative complications were similar between the 2 groups. Preoperative history of trabeculectomy was a significant risk factor for surgical failure of Ahmed valve implantation in NVG (relative risk=4.618; P=0.018 by Cox regression model). CONCLUSIONS: Intraoperative IVB injection does not seem to be helpful for better surgical outcomes of Ahmed valve implantation in NVG. A history of trabeculectomy is a risk factor for failure after Ahmed valve implantation in patients with NVG.
Park, Chan,Shin, Bo-Sung,Kang, Moon-Suk,Ma, Yong-Won,Oh, Jae-Yong,Hong, Sung-Moo Korean Society for Precision Engineering 2015 International Journal of Precision Engineering and Vol.16 No.7
A new micro porous patterning method was proposed in this paper. We experimentally demonstrated the feasibility of this method using UV laser hybrid process with polymer sheet. The PP(Polypropylene) sheet of 0.1mm thickness was firstly mixed with CFA(Chemical Foaming Agent), and then the desired porous pattern was selectively fabricated by 355nm UV pulse laser processing. According to processes parameters such as laser fluence, processing time and CFA density, the characteristic of porosity which is pore size, pore density and pore type was proven to be controllable. From these experimental results, it was possible to manufacture micro porous patterned polymer sheet.
( Kyoung Tak Ma ),( Sang Hyup Lee ),( Sa Min Hong ),( Kyoung Soo Park ),( Chan Yun Kim ),( Gong Je Seong ),( Young Jae Hong ) 대한안과학회 2008 Korean Journal of Ophthalmology Vol.22 No.1
Purpose: To assess the relationship between the retinal thickness analyzer (RTA) parameters, and those of the GDx VCC scanning laser polarimeter (GDx VCC), Stratus OCT optical coherence tomography (Stratus OCT), and Heidelberg retinal tomograph II confocal scanning laser ophthalmoscopy (HRT II). Methods: Twenty-nine primary open-angle glaucoma patients were retrospectively included in this study. Measurements were obtained using the RTA, GDx VCC, Stratus OCT, and HRT II. We calculated the correlation coefficients between the parameters of RTA and those of the other studies. Results: Among the optic disc parameters of RTA, the cup volume was best correlated with Stratus OCT (R=0.780, p<0.001) and HRT II (R=0.896, p<0.001). Among the posterior pole retinal thickness parameters, the posterior pole abnormally thin area (PPAT) of the RTA and the inferior average of the GDx VCC were best correlated (R=-0.596, p=0.001). The PPAT of the RTA and the inferior maximum of the Stratus OCT were best correlated (R=-0.489, p=0.006). The perifoveal minimum thickness (PFMT) of the RTA and the cup shape measurement of the HRT II were best correlated (R=-0.565, p=0.004). Conclusions: Many RTA optic disc parameters were significantly correlated with those of the Stratus OCT and HRT II. The RTA posterior pole retinal thickness parameters were significantly correlated with those of the GDx VCC, Stratus OCT and HRT II. The RTA optic disc and posterior pole retinal thickness parameters may be valuable in the diagnosis of glaucoma. Korean Journal of Ophthalmology 22(1):10-17, 2008
Kyoung Tak Ma,Sang Hyup Lee,Samin Hong,Kyoung Soo Park,Chan Yun Kim,Gong Je Seong,Young Jae Hong 대한안과학회 2008 Korean Journal of Ophthalmology Vol.22 No.1
Purpose: To assess the relationship between the retinal thickness analyzer (RTA) parameters, and those of the GDx VCC scanning laser polarimeter (GDx VCC), Stratus OCT optical coherence tomography (Stratus OCT), and Heidelberg retinal tomograph II confocal scanning laser ophthalmoscopy (HRT II). Methods: Twenty‐nine primary open‐angle glaucoma patients were retrospectively included in this study. Measurements were obtained using the RTA, GDx VCC, Stratus OCT, and HRT II. We calculated the correlation coefficients between the parameters of RTA and those of the other studies. Results: Among the optic disc parameters of RTA, the cup volume was best correlated with Stratus OCT (R=0.780, p<0.001) and HRT II (R=0.896, p<0.001). Among the posterior pole retinal thickness parameters, the posterior pole abnormally thin area (PPAT) of the RTA and the inferior average of the GDx VCC were best correlated (R=-0.596, p=0.001). The PPAT of the RTA and the inferior maximum of the Stratus OCT were best correlated (R=-0.489, p=0.006). The perifoveal minimum thickness (PFMT) of the RTA and the cup shape measurement of the HRT II were best correlated (R=-0.565, p=0.004). Conclusions: Many RTA optic disc parameters were significantly correlated with those of the Stratus OCT and HRT II. The RTA posterior pole retinal thickness parameters were significantly correlated with those of the GDx VCC, Stratus OCT and HRT II. The RTA optic disc and posterior pole retinal thickness parameters may be valuable in the diagnosis of glaucoma. Korean Journal of Ophthalmology 22(1):10-17, 2008
Woo, Dong-Chan,Koo, Chang-Young,Ma, Hong-Chan,Lee, Hee-Young The Korean Institute of Electrical and Electronic 2012 Transactions on Electrical and Electronic Material Vol.13 No.5
Antimony doped tin oxide (ATO) thin films on glass substrate were prepared by the chemical solution deposition (CSD) method, using sol-gel solution synthesized by non-alkoxide precursors and the sol-gel route. The crystallinity and electrical properties of ATO thin films were investigated as a function of the annealing condition (both annealing environments and temperatures), and antimony (Sb) doping concentration. Electrical resistivity, carrier concentration, Hall mobility and optical transmittance of ATO thin films were improved by Sb doping up to 5~8 mol% and annealing in a low vacuum atmosphere, compared to the undoped tin oxide counterpart. 5 mol% Sb doped ATO film annealed at $550^{\circ}C$ in a low vacuum atmosphere showed the highest electrical properties, with electrical resistivity of about $8{\sim}10{\times}10^{-3}{\Omega}{\cdot}cm$, and optical transmittance of ~85% in the visible range. Our research demonstrates the feasibility of low-cost solution-processed transparent conductive oxide thin films, by controlling the appropriate doping concentration and annealing conditions.