3단 구성의 디지털 DLL 회로

박철우,강진구,Park, Chul-Woo,Kang, Jin-Ku 한국전기전자학회 2002 전기전자학회논문지 Vol.6 No.1

본 논문에서는 전부 디지털 회로로 구성된 고 해상도의 DLL(Delay Locked Loop)를 제안하였다. 제안된 회로는 위상 검출기, 지연 선택 블록, 그리고 각각의 지연 체인을 가지는 Coarse, Fine 그리고 Ultra Fine 위상조정 블록의 삼 단의 형식으로 되어 있다. 첫 번째 단은 Ultra Fine 위상조정블록으로 고 해상도를 얻기 위하여 Vernier Delay Line을 사용하였다. 두 번째와 세 번째 단은 Coarse와 Fine 위상조정블록으로 각각의 단위 지연 체인을 이루는 단위 지연 소자의 해상도 만큼의 위상 제어를 하게 되며, 두 단은 상당히 비슷한 구조를 이루고 있다. 회로는 HSPICE를 이용하여 공급 전압이 3.3V인 $0.35{\mu}m$ CMOS 공정으로 시뮬레이션 되었다. 시뮬레이션 결과 회로의 해상도를 약 10ps로 높일 수 있었으며, 동작 범위는 250MHz에서 800MHz 이다. This paper describes a high resolution DLL(Delay Locked Loop) using all digital circuits. The proposed architecture is based on the three stage of coarse, fine and ultra fine phase tuning block which has a phase detector, selection block and delay line respectively. The first stage, the ultra fine phase tuning block, is tune to accomplish high resolution using a vernier delay line. The second and third stage, the coarse and fine tuning block, are tuning the phase margin of Unit Delay using the delay line and are similar to each other. It was simulated in 0.35um CMOS technology under 3.3V supply using HSPICE simulator. The simulation result shows the phase resolution can be down to lops with the operating range of 250MHz to 800MHz.

EDISON Co-rotational Plane Beam-Dynamic Tip Load를 이용한 가진주파수 변화에 따른 외팔보의 자유단 진동 연구

박철우,주현식,류한열,신상준,Park, Chul-Woo,Joo, Hyun-Shig,Ryu, Han-Yeol,Shin, Sang-Joon 한국전산구조공학회 2015 한국전산구조공학회논문집 Vol.28 No.5

본 논문에서는 Euler-Bernoulli Beam(EB-beam) 및 신속 Fourier 변환을 이용하여 수치분석적 빔 모델 및 Co-rotational plane beam EDISON program(CR-beam)을 이용한 빔 모델의 가진주파수 변화에 따른 외팔보의 자유단 진동 연구를 수행하였다. 위의 두 빔 모델에서의 끝단에서는 진동이 시간이 지남에 따라 감소하다가 정상상태에 이르는 것을 확인하였다. 끝단에서 가진주파수가 증가함에 따라 구조적 감쇠에 의해 변위이 감소하는 경향을 보인다. 감쇠를 고려한 EB-beam과 CR-beam가 정상상태로 진입하는 경향이 비슷하나, 가진주파수는 정상상태가 나타나는 시간과 독립적임을 제시한다. In this paper, Euler-Bernoulli beam theories(EB-beam) are used, and Fast Fourier Transformation(FFT) analysis is then employed to extract their natural frequencies using both analytical approach and Co-rotational plane beam(CR-beam) EDISON program. EB-beam is used to analyze a spring-mass system with a single degree of freedom. Sinusoidal force with various frequencies and constant magnitude are applied to tip of each beam. After the oscillatory tip response is observed in EB-beam, it decreases and finally converges to the so-called 'steady-state.' The decreasing rate of the tip deflection with respect to time is reduced when the forcing frequency is increased. Although the tip deflection is found to be independent of the excitation frequency, it turns out that time to reach the steady state response is dependent on the forcing frequency.

몬테 카를로 시뮬레이션을 통한 발사관 구조 안전성 분석

박철우,이온수,신효섭,박진용,이동주,Park, Chul-Woo,Lee, Onsoo,Shin, Hyo-Sub,Park, Jin-Yong,Lee, Dong-Ju 한국시뮬레이션학회 2018 한국시뮬레이션학회 논문지 Vol.27 No.4

Launching system is designed to store the payload, withstand the rigors, and prevent it from rusting and damaging. The behavior during initial deployment of the missile is determined by production, assembly and insertion condition of a launching tube and a missile. The purpose of this research is to confirm the safety of a launching tube by statistically analyzing behavior of the missile, during initial deployment stage. Error parameters which effect initial behavior of the missile are selected and analyzed through Monte-Carlo Simulation. Based on the result of simulation, tip-off and stress distribution between rail and shoe is predicted by using the commercial analysis program called Recurdyn. Lastly, the safety factor is calculated based on yield strength of the material and maximum stress of the rail during the process of launching. The safety of the launching system is verified from the result of the safety factors. 발사관은 탑재물을 보관하고 외부 환경으로부터 부식 및 파손되는 것을 방지하는 역할을 한다. 발사관과 유도탄의 제작, 조립 그리고 장입 상태에 따라 발사할 때 유도탄의 초기 거동을 결정하게 된다. 본 연구의 목적은 유도탄이 발사관에서 사출될 때 유도탄의 초기 거동을 결정하는 요소를 통계적으로 분석하여 발사관의 안전성을 확인하는 것이다. 유도탄이 발사될 때 거동에 영향을 주는 오차 요소들을 선정한 후 Monte-Carlo 시뮬레이션을 수행하여 통계적으로 분석하였다. 시뮬레이션 결과를 바탕으로, 각 오차 요소들을 고려한 다물체 동역학 해석을 상용프로그램인 Recurdyn을 이용하여 동역학 해석을 수행하여 유도탄 발사할 때 발생하는 중력 침하 및 레일과 슈 사이에 발생하는 응력을 구하였다. 해당 결과를 바탕으로 현재 설계된 발사관에 대한 안전성을 검증하였다.

강유전 고분자 박막의 상전이 특성

박철우,정치섭,Park, Chul-Woo,Jung, Chi-Sup 한국전기전자재료학회 2014 전기전자재료학회논문지 Vol.27 No.2

Phase transition properties of the copolymer films of polyvinylidene fluoride (PVDF) and trifluoroethylene(TrFE), P(VDF-TrFE), were studied with X-ray diffraction (XRD) and polarization modulated ellipsometry (PME). XRD studies on both Langmuir-Blodgett (LB) films and spin coated films exhibit conversions from ferroelectric phase to paraelectric phase at $108{\pm}2^{\circ}C$ on heating and paraelectric phase to ferroelectric phase at $78{\pm}2^{\circ}C$ on cooling. The presence of the ferroelectric-paraelectric phase transition is also confirmed by the PME technique for the first time in this study. PME was proved to be a very sensitive tool in the measurement of the structural changes at the nano-thickness films.

강유전 고분자 박막의 저차원 전기광학 특성

박철우,정치섭,Park, Chul-Woo,Jung, Chi-Sup 한국전기전자재료학회 2014 전기전자재료학회논문지 Vol.27 No.3

The electro-optic properties in Langmuir Blodgett films of poly (vinylidene fluoride trifluoroethylene) are investigated in the crossover region between two and three dimensions. The absence of finite size effect is observed in the films thinner than 20 nm, which confirms that these films are two dimensional ferroelectrics. The copolymer LB film of P(VDF-TrFE) exhibits the largest electro-optic response(26 pm/V) at 10 layer thickness. The cross-over behavior of electro-optic effect around the 10 layer thickness was discussed with the formation of nanomesa after thermal annealing.

유동해석을 통한 스크롤 압축기 성능에 관한 연구

박철우(Chul woo. Park),최현진(Hyun jin. Choi),박선명(Sun myung. Park),김종목(Jong mok. Kim) (사)한국CDE학회 2015 한국 CAD/CAM 학회 학술발표회 논문집 Vol.2015 No.동계

전압제어 기반 역률보상시스템의 고조파 왜곡에 강인한 제어 방법

박철우(Chul-woo Park),정상현(Sanghyun Joung),박일형(Il-Hyung Park) 제어로봇시스템학회 2017 제어·로봇·시스템학회 논문지 Vol.23 No.10

In this paper, we propose a new power factor compensation system and a robust control method for harmonic distortion. In the conventional power factor compensation system using a capacitor bank method, the power factor compensation error occurs depending on the load condition because of the limitation of the compensation capacitor capacity. The power triangle method and time delay method are used for control, but errors occur in harmonic distortion conditions. The proposed power factor compensation system compensates the power factor by adjusting the output voltage of the slidac. Using the new control method based on the DQ conversion, we can obtain an accurate power factor compensation even in harmonic distortion onditions. If the proposed power factor compensation system is applied to an industrial field, the power factor compensation performance can be maximized. Consequently, it is possible to reduce electricity prices, reduce line loss, increase the load capacity, ensure the transmission margin capacity, and reduce the amount of power generation.

이온풍 공랭 방식 적용을 위한 방송용 LED 조명장치의 냉각 특성 해석

박철우(Chul-Woo Park),이승준(Seungjun Lee),김대중(Daejoong Kim) 대한설비공학회 2012 설비공학 논문집 Vol.24 No.9

In the present work, numerical analyses of broadcasting LED light with ion wind generator have been carried out for enhancement of cooling performance. Ion wind generator is produced and experimented before analysis. With the use of result of experiments, broadcasting LED light model is computed. Ion wind velocity into LED light is varied with 0~3 m/s. Based on the numerical results, the area of duct-type ion wind generator was designed to reduce the volume flow rate of ion wind. The modified inlet geometry shows sufficient cooling capability. And, through modified ion wind generator, the volume flow rate of ion wind has been largely reduced.

자동차 부품용 마그네슘 합금 관재 압출공정조건 분석

박철우(Chul Woo Park),김호윤(Ho Yoon Kim) 대한기계학회 2012 大韓機械學會論文集A Vol.36 No.12

경량화는 대기오염과 자원고갈의 측면에서 매우 중요하게 인식되고 있어, 많은 자동차용 부품이 Al 및 Mg 합금으로 대체되었으며, 관련 연구가 지속적으로 증가하고 있다. 그러나 Mg 합금은 Al 합금에 비해 높은 재료비와 난성형성으로 인한 낮은 생산성 때문에 제한적으로 적용되고 있다. 본 연구에서는 FEA를 이용하여 자동차 범퍼 백 빔용 관재에 대한 공정조건을 분석하였으며, 생산성을 향상시킬 수 있는 방법을 확립하였다. 물성치 확보를 위해 물성시험을 수행하였으며, 소성변형 중 발생하는 열 관련 물성을 정의하기 위하여 단순형상에 대한 실험과 해석을 수행하였다. 이후 온도조건 및 램 속도를 고려하여 제품에 대한 해석을 수행하였다. 이를 통하여 압출공정조건을 확립하였으며, 표면결함이 없는 제품을 성형하는데 성공하였다. Weight reduction is increasingly being considered very important in light of air pollution and the exhaustion of resources. As a result, many automotive components are being replaced by Al and Mg alloys, and studies are increasingly focusing on the same. However, the use of Mg alloys is limited because they have higher material cost and lower productivity owing to the difficult forming conditions compared with Al alloys. In this study, the tube extrusion process conditions of an automotive bumper back beam were analyzed using FEA. Material tests were performed to determine the properties, and experiments and analyses for a simple shape were performed to define the data for heat generation during plastic deformation. Then, the analyses of the product were carried out by considering various temperatures and ram speeds. The conditions were then established, and a product without surface defects was extruded successfully.

모바일 뱅킹의 수용 의도에 영향을 미치는 요인

박철우(Chul-woo Park),안중호(Joong-ho Ahn),장정주(Jung-joo Jahng) 한국인터넷전자상거래학회 2007 인터넷전자상거래연구 Vol.7 No.3

The main objective of this research is to find factors affecting the intention to accept information technology in a mobile environment. In order to explain the intention to adopt the mobile banking service in which uncertainty and risk exist, the factor of trust is added on the technology acceptance model widely used in the information system discipline. In this study covering acceptance of innovative technology of mobile banking, TAM and Web trust model are introduced as basic theories to explain phenomena in mobile area. In addition, social influence is considered as an explaining factor as well as usefulness and ease of use. Mobile service area should be studied in view of psychological and social characteristics as well as technical aspects. That is, multidimensional approaches and analyses for user behavior will be available by grasping the intention to accept from the point of psychological, managerial, and sociological view.