고양이 중뇌 흑색질의 Dopamine 면역반응세포에 관한 면역세포화학적 연구

모근석,문정석,김종중,김준수,정윤영,장인엽,김흥중 대한해부학회 1996 Anatomy & Cell Biology Vol.29 No.5

흰쥐 뇌에서 Neuropeptide-Y 분비세포의 출현시기 및 발육에 관한 면역조직화학적 연구

모근석,김종중,정윤영,장인엽,문정석,김준수,김흥중 대한해부학회 1996 Anatomy & Cell Biology Vol.29 No.5

Al/p - Si MIS 형 태양전지의 물성에 관한 연구

이수대,채건식,설정식,김영국,김일홍 慶南大學校 附設 基礎科學硏究所 1989 硏究論文集 Vol.1 No.-

The metal-thin insulating film-semiconductor structure is currently receiving much attention in solar cell studies. In this a MIS solar cell consisting of aluminum on single and poly silicon with an interfacial oxide layer(∼20Å) have been fabricated by vacuum evaporation method and found a good reproducibility. Recent studies show the importance of surface and interfacial oxide thickness. An interfacial of 20∼30Å is optimum and may be achieved by furnace heating to 600℃ in 800cc/min O₂flow. These cells have good rectification with forward and reverse voltage under dark condition. The best Al/p-Si Si solar cell has an open circuit voltage Voc=0.4V, short circuit current density Isc=30mA/㎠, fill factor FF=0.58 and conversion efficiency η=10% for single crystal, and Voc=0.33 V, Isc=30mA/㎠, FF=0.49 and η=5% for poly crystalline silicon substrates for 70mA/㎠ irradiation of AM₂.

미량 Ni 첨가 Fe-Ni 합금의 고온산화 거동에 관한 연구

孫根洙,尹在弘,金晋夏,金顯洙,成田敏夫,林重成 대한금속재료학회 2002 대한금속·재료학회지 Vol.40 No.10

Oxidation behavior of Fe-Ni alloys added by small amount of Ni was studied, under the exposure to the temperatures up to 1100℃, 1150℃, and 1200℃, respectively. The slope of mass change curve representing an oxidation rate was 1 or 2 up to 20 seconds and decreased to 1/2 after 20 seconds in a parabolic shape. The temperature of the initial stage of oxidation increased more quickly at the furnace inside than at the surface of the specimen, and its behavior was reversed due to oxidation heat after 20 seconds later. Oxide layer was mainly composed of FeO. And particle of Fe_3O_4 and Fe_2O_3 was distributed in FeO layer. The order of the composition ratio for the oxide was Fe_2O_3,·Fe_3O_4,·FeO at the oxide surface, FeO,·Fe_3O_4,·Fe_2O_3 at the internal oxide, and FeO,·Fe_3O_4,·Fe_2O_3 at the surface of metal after stripping oxide layer.

개선된 Bridgman법으로 성장한 Bi₂Sr₂CaCu₂O_(8+δ) 單結晶의 초전도성

채건식,손인호,설정식,이수대,김영국,전동성,오재근,강성욱 경남대학교 환경문제연구소 1995 환경연구 Vol.17 No.-

The Bi₂Sr₂CaCu₂O_(8)+_(δ) single crystals are grown from the melt using a stoichiometric starting composition fer the cautions. The size and thickness of the Bi₂Sr₂CaCu₂O_(8)+_(δ) crystals depends on the cooling rate. The lower the cooling rate, the bigger and thicker the Bi₂Sr₂CaCu₂O_(8)+_(δ) crystals become. Bi₂Sr₂CaCu₂O_(8)+_(δ) X-ray diffraction(XRD) measurements of the single crystals were carried out using the radiation source of Cu Kα . In these Patterns only the (0,0,2n) diffraction appeared. The result indicated that the cleared surface of the single crystal was of the a-b face, and that the single crystal had a single phase without any undergrowth with 7K and 85K phases. In addition, although the figure is not shown, XRD patterns from (006) to (00□) were observed in the range of 2θ=0 to 60 degrees. The characterization of as-grown single crystals have been analyzed by Laue X-ray backsdattering along the c-axis and X-ray precession experiments. The result of magnetic moment vs Tc in 10 Gauss for a crystals were measurements indicated that the samples have a superconducting transition temperature of 85K.

친수성으로 표면개질한 폴리설폰막의 투과플럭스

송근호,김강희,조성헌,이광래,임종호,배성수 한국화학공학회 2004 Korean Chemical Engineering Research(HWAHAK KONGHA Vol.42 No.1

실관막형 폴리설폰 막의 표면을 2-hydroxyethylmethacrylate(HEMA)로 코팅하였으며, 코팅인자들인 azobisisobutyronitrile(AIBN)/HEMA 성분비, 용매의 종류(물, 메탄올), UV 조사시간 등이 투과플럭스에 미치는 영향을 조사하였다. AIBN/HEMA/ 메탄온ㄹ 용액으로 코팅한 막이 AIBN/HEMA 성분비가 높고, UV 조사시간이 길수록 투과플럭스가 높았다. AIBN/HEMA 성분비가 낮으면 동일한 투과플럭스를 얻기 위하여 UV조사시간을 더 길게 하여야 하며, 특정한 AIBN/HEMA 성분비와 UV 조사시간에서 코팅한 막의 투과플럭스는 원래의 막(코팅하지 않은 막)보다 높게 나타났다. 또한, 오일에멀젼에 의한 fouling은 코팅한 막과 원래의 막에 모두 나타났지만, 코팅한 막의 fouling이 원래의 막 보다 현저히 낮았다. 즉, fouling 발생 후 코팅한 막의 수투과 플럭스(0.2683g/㎠ㆍmin)는 코팅하지 않은 막(0..448g/㎠ㆍmin)보다 약 6배 이상으로 높게 유지되었다. A hollow-fiber type polysulfone UF membrane was surface-coated with 2-hydroxyethylmethacrylate(HEMA). The effect of various coating paramters on permeation flux was investigated, such as concentration ratio of Azobisisobutyronitrile(AIBN)/HEMA, solvent (water or methanol), and UV irradiation time. The membrane coated with a solution of AIBN/HEMA/methanol showed about 2.65 times higher water flux than that coated with a solution of AIBN/HEMA/water. The membrane coated with a solution of higher AIBN/HEMA ratio and a longer UV irradiation time exhibited a higher permeation flux. The membrane coated with a solution of lower AIBN/HEMA ratio needed a longer UV irradiation time for coating to get a same level of permeation flux. In order to have a greater permeation flux than uncoated membrane, the membrane should be coated with a solution of a certain AIBN/HEMA ratio and UV irradiation time. The fouling by oil emulsion occurred to both of the coated and the uncoated membrane. However, the fouling of coated membrane was much less than uncoated one; the water flux(0.2683g/㎠·min)through the coated membrane was about 6 times higher than that(0.0558g/㎠·min) through the uncoated membrane.

Lead Germanate 단결정의 초음파 감쇠

이수대,채건식,김영국,설정식 慶南大學校 附設 基礎科學硏究所 1989 硏究論文集 Vol.1 No.-

The temperature dependence of the ultrasonic velocity of 10 MHz and the absorption coefficient in the 10-30MHz range by the pulse echo method were determined in lead germanate single crystal. The velocity of longitudinal 10 MHz ultrasound along the c axis changed anomalously at the phase transition point and the jump was approximately 50m/sec. Near Curie point, the relaxation time and the kinetic coefficient of electric polarization from the Landau-Khalatnikov theory were calculated as ?? sec and ??, respectively. At room temperature, the viscosity tensor were measured as, ?? in the MKS units.

죽염 처리 청국장의 기능성 증진

김수옥,박수영,이숙희,박건영 대한암예방학회 2003 Journal of cancer prevention Vol.8 No.4

12주간의 유산소성 운동이 비만 초등학생의 신체조성과 혈액성분에 미치는 영향

윤미수,최건식,고성경,정소봉 한국스포츠리서치 2004 한국 스포츠 리서치 Vol.15 No.5

[Purpose] The purpose of this study was to investigate the effect of aerobic exercise training on the body composition and blood components in obese elementary children after 12 weeks. [Methods] Subjects of this study were composed of 20 male students ranging in age from 9 to 12 years who were classified into two groups, obese exercise group(n=10) and normal control group(n=10). For 12 weeks, obese exercise group performed the aerobic exercise training that the program was composed by Yoon. The blood samples were taken before and after 12 week Paired t-Test was adopted to analyse the difference between before and after aerobic exercise training. [Results] body fat of obese exercise group was decreased 4.8% after aerobic exercise training(p<.01) and that of normal control group was decreased 0.1% during same time(NS). Among the blood lipoprotein, total cholesterol(p<.01), LCL-C(p<.01), and triglycerides(p<.05) of obese exercise group were decreased after aerobic exercise training, but not changed HDL-C of same group. Red blood cell, Hemoglobin(p<.65) of obese exercise group were increased after aerobic exercise training. Glucose of obese exercise group were decreased after aerobic exercise training(p<.05), but not changed in Ca and P. [Conclusion] In conclusion, aerobic exercise training for 12 weeks seems to reduce body might and body fat, and to change the profiles of blood Component in obese elementary children.

소규모 제조업에서 재해발생과 사업장 특성간의 관련성 분석

이건세,김형수,,장성훈,정최경희,오원기,최재욱,이관형,오지영 大韓産業醫學會 2006 대한직업환경의학회지 Vol.18 No.2

목적: 소규모 제조업 사업장의 재해 발생 유무에 따른 사업장 조직 특성을 비교하여 재해 발생과 관련된 요인을 사업장 수준에서 파악하고자 하였다. 방법: 한국산업안전공단이 실시한 2004년도 산업안전 보건 동향조사 자료 중 5인 이상 50인 미만 제조업 1,886개 사업장(가중치를 부여하여 추정한 모집단 사업장은 65,921개)의 재해(산재 및 공상, 경상 포함) 발생 여부와 사업장의 조직 특성(일반적 특성, 고용특성 및 산업안전보건 특성)간 다변량 분석을, 사업장의 일반적 특성은 지역, 산업형태, 업종 등이며, 고용특성은 전체 근로자중에서 생산직 근로자의 분포, 여성근로자의 분포, 1주일 평균 근로시간, 교대근무 등이며, 산업안전보건 특성은 안전관리자/보건관리자의 선임형태, 산업안전보건위원회, 노동조합, 매월 정기안전보건교육시간, 안전보건관리 규정, 안전보건활동 점수, 안전문화 점수 등이다. 결과: 다변량 분석결과 재해가 발생한 사업장이 갖는 특성은 다음과 같았다. 첫째, 사업장의 일반적 특성에서 지역별로는 경인권에 비해 전라권, 산업형태 면에서 원청에 비해 사외협력업체, 업종별로는 전자부품/통신에 비해 코크스/석유정제업, 목재/나무제품업, 음식료품, 조립 금속제품에서 위험도가 높았다. 둘째, 사업장의 고용 특성에서는 전체 구성원 중에서 생산직 근로자가 증가할수록 재해발생 사업장이 유의하게 증가하였으며, 여성근로자의 증가할수록 재해발생 사업장이 유의하게 감소하였다. 주당 근무시간이 증가할수록 재해 발생 사업장이 유의하게 증가하였으며, 교대 근무와 사업장의 재해발생과는 유의한 관련성이 없었다. 셋째, 사업장의 산업안전보건 특성에서는 안전관리자가 전임으로 근무할수록, 산안전보건위원회가 활발히 활동할수록, 노동조합이 설립될수록, 안전보건규정이 갖추어지지 않을수록, 정기보건교육시간이 많을수록, 안전문화수준이 낮을수록 재해발생 사업장이 유의하게 증가하였다. 결론: 소규모제조업에서 사업장의 조직 특성에 따라 사업장 재해율이 다름을 확인할 수 있었으며, 이는 산업재해의 예방을 위해서는 근로자 요인이외에도 사업장 수준에서의 관련요인에 대한 접근이 필요함을 의미한다. Objective: This study evaluated the relationship between injury occurrence and workplace organization in small-sized, manufacturing factories in Korea. Methods: Using data from the 2004 Occupational Safety and Health Survey in Korea, this study compared workplace organizational factors (general characteristics, employee characteristics and health and safety characteristics) with injury occurrence of 1,866 small-sized, manufacturing factories (65,921 population factories after weighting). General characteristics of factories comprised location, type and classification of industry. Employee characteristics comprised proportion of manual workers and female workers, average working hours per week and shiftwork. Health and safety characteristics comprised type of safety and health manager, committee for occupational safety and health, labor union, health and safety regulation, monthly health and safety training time, score of health and safety activity and score of safety culture. Results: The following characteristics of injury-occurrence in small-sized, manufacturing factories were determined by multivariate analysis. In terms of general characteristics, the risk of injury-occurrence was higher in Jeolla area than Gyeongin area in outside associate than other enterprises and in coke, refined petroleum products and nuclear fuel, wood and products of wood, food products and beverages and fabricated metal products, except machinery and furniture industries than television and communication equipment and apparatus industries. In terms of employee characteristics, injury-occurrence significantly increased in factories with greater proportion of manual worker and with a higher rate of working hours per week. But significantly decreased in factories with a higher proportion of female workers. In terms of health and safety characteristics, injury-occurrence significantly increased in factories with a self-appointed safety manager, with unorganized union, with a more active committee for occupational safety and health, with unimplemented health and safety regulation, with longer monthly safety and health training time, and with a lower score of safety culture. Conclusions: This study demonstrated that several factors of workplace organization were significantly related with injury-occurrence in factories. These findings are supposed to raise the need for making effort in workplace organization to improve injury prevention.