http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
강관의 하이드로포밍시 성형구간과 공정인자에 대한 실험적 연구
안익태(I. T. An),현도익(D. I. Hyun),김봉준(B. J. Kim),문영훈(Y. H. Moon) 대한기계학회 2002 대한기계학회 춘추학술대회 Vol.2002 No.4
Tube hydroforming has attracted increased attention in the automative industry recently. It can produce wide range of products such as subfrarnes, engine cradles, and exhaust manifolds with cheaper production cost by reducing overall number of processes. The purpose of this study is to trace cause of these forming failure and to make optimal process condition. Expermental studies have been performed to investigate the effects of each parameters such as internal pressure, axial feeding and holding time. Tubes used in the experiment are SPS290 and SAPH38P. In case of the T-fitting bulge height at initial process, middle process and last process are investigated and then compared. In the cylindrical hvdroforming the effect of holding time has been observed.
탄소강 후판용접부의 피로수명 및 잔류응력에 미치는 열처리 영향
안익태 ( I. T. An ),김원태 ( W. T. Kim ),조종래 ( J. R. Jo ),문영훈 ( Y. H. Moon ) 한국열처리공학회 2003 熱處理工學會誌 Vol.16 No.3
N/A The effects of heat treatment on the fatigue life and welding residual stress of welded plates were investigated in this study. The plates were welded by flux cored are welding process, and post weld heat treated at 600℃ for 1 hour. The residual stresses of welded plates before and after post weld heat treatment were measured by hole drilling method. To measure the fatigue life of welded plates, low cycle fatigue tests under strain control and high cycle fatigue tests under load control were performed respectively, by using cylindrical specimens containing weld metal and heat affected zone. The obtained result shows that the post weld heat treatment reduces the residual stress, and resultantly changes the fatigue life of welded plate. Goodman diagrammatic analysis has also been performed to study the effect of post weld heat treatment on the high cycle fatigue life.
최성기,안익태,문영훈,Choi, Sung-Ki,Ahn, Ick-Tae,Moon, Young-Hoon 대한기계학회 2004 大韓機械學會論文集A Vol.28 No.7
During the tube hydropiercing, the region adjacent to the pierced hole will be deformed and will be drawn away from the die block as the punch advances through the wall of the tube. The deformation in the region may range from a substantially flat form to a countersunk form, so called rollover. In this study, the effects of material properties, shape of piercing punches, roundness of tube surface and internal pressure within the tube during piercing on the rollover have been investigated experimentally. The results provide the quantitative variation of rollover at given hydropiercing parameters, and a relationship between the deformed radius and the rollover caused by the deformation has been established.
盧載植,安翼泰 단국대학교 대학원 1988 學術論叢 Vol.12 No.-
This study is to present the areal reduction factor which is the relationship between the point rainfall and areal rainfall within four fixed-area in the Han River basin through the regional frequency analysis. The storm-events annual maximum rainfall data over the Han River basin can be formulated to be the type of exponential distribution. The areal reduction factor can be estimated from the point and areal frequency curve of the four fixed-area. The results of this study are available for the supplement and expansion of the point rainfall lacking closely spaced data, and provide a more reliable input for rainfall-runoffmodels.