연료액위센서용 Mn-Co-Ni 산화물계 서미스터의 전기적 특성에 미치는 열처리 및 소결미세구조에 관한 연구

나은상,백운규,최성철 한국결정성장학회 2003 韓國結晶成長學會誌 Vol.13 No.2

본 연구에서는, Mn-Co-Ni 산화물계 NTC 써미스터의 열처리 조건에 따른 전기적 특성간의 상호관계에 대하여 고찰하였으며, 이를 위해 XRD. 소결체 밀도측정 및 B정수, 저항 열방산정수 등의 전기적 특성치를 조사하였다. NTC 써미스터의 열처리 과정은 Mn-Co-Ni 산화물 시험편의 소결특성에 큰 영향을 미치고있었으며, 본 연구의 조성하에서는 $1250^{\circ}C$, 2시간 동안 열처리한 경우 가장 높은 밀도치를 얻을 수 있었다. 이 조건하에서 미세구조 관찰결과 치밀화과정이 거의 완전하게 이뤄짐을 확인하였다. 제조된 NTC 써미스터는 소결 온도가 상승함에 따라 저항값 및 B 정수값이 커지는 것을 확인하였으며, 연료 액위의 변화에 다른 출력전압의 거동을 측정한 결과 선형 감소 거동을 나타내었다. 따라서, 본 연구에서 제조된 Mn-Co-Ni 산화물계 NTC 써미스터의 전기적 특성은 열처리 조건과 밀접한 연관성이 존재하는 것으로 사료되며, 향후 자동차용 연료액위센서로의 응용성이 가능할 것으로 기대된다. The correlationship between heat treatment condition and electrical properties of the Mn-Co-Ni oxide NTC thermistor for fuel level sensor was investigated by the X-ray diffractometry, density measurement, and electrical properties measurement such as resistivity, B constant, and thermal dissipation constant. It was shown that the heat treatment of NTC thermistor was responsible for sinterability of Mn-Co-Ni oxide. The highest density of 5.10 g/㎤ was obtained at $1250^{\circ}C$, 2 hours, at which the densification was almost completed. This is also manifested from the microstructural observation. It is found that the electrical resistivity and B constant are increased at the elevated sintering temperatures. The NTC specimens prepared in this study showed the conventional decrease of resistance with the measured temperature and the linear behavior of output voltage with fuel levels. Therefore, the electrical properties of thermistor were closely correlated with sintering condition. and the Mn-Co-Ni oxide thermistor prepared in this study has a great possibility enough to apply for an automobile fuel level sensor.

두가지 형태의 columbite precursor 법에 제조된 $Pb(Ni,Nb)O_3-Pb(Zr, Ti)O_3$ 세라믹스에서의 유전 및 압전 특성에 및는 CuO 의 첨가영향

나은상,최성철 한국세라믹학회 1999 한국세라믹학회지 Vol.36 No.11

$Pd_{(1-x)}$$Cd_x$[(Mn, Sb), Zr, $Ti]O_3$ 세라믹스의 소결 거동 및 압전 특성에 대한 연구

나은상,최성철 한국세라믹학회 2000 한국세라믹학회지 Vol.37 No.4

In this study, we chose the basic composition which indicated the best electrical properties by change of x content(0, 0.05, 0.1, 0.15, 0.2, 0.25 mol respectively) in xPb(Mn1/3Sb2/3)O3-(1-x)Pb(Zr0.52Ti0.48)O3 ceramics. And we substituted Cd2+ for Pb2+ site, then observed the sintering behavior, microstructure and electrical propertties according to the various sintering temperature. The basic composition was the 0.05PMS-0.95PZt, and it showed single perovskite phase and excellent properties. In case of Cd2+ substitution, we were able to sinter at 90$0^{\circ}C$ which was lower than conventional sintering temperature(1200~130$0^{\circ}C$). Especially, when the 2mol% substituted PMS-PZT specimens were sintered at 90$0^{\circ}C$ for 2h, we obtained the p=7.6g/㎤, kp=56%, Qm=520 and made sure of a position of Cd2+ substitution by observing lattice parameter, phase transition temperature. From this results, we could infer that because Cd2+ substituted fro A-site, low temperature sintering of Cd2+ substituted PMS-PZT without any loss of electrical properties shows its applicability for the piezoelectric ceramic transformer.

NiO-Doped Pb(Ni$_{1}$3/Nb$_{2}$3/)O$_3$-PbTiO$_3$-PbZr$_3$-O세라믹스의 전기 및 기계적 특성에 관한 연구

나은상,김윤호,최성철 한국결정성장학회 2000 한국결정성장학회지 Vol.10 No.3

Pb($(Ni_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3$세라믹스에서 NiO첨가에 따른 유전, 압전 및 기계적 특성의 변화를 연구하였다. Columbite precursor법을 사용하여 분말을 제조 후 공기중에서 $1100^{\circ}C$~$1250^{\circ}C$의 온도로 2시간 소결하여 시편을 제조하였다. $1150^{\circ}C$이하 온도에서 소결한 시편에서는 NiO를 1 mol% 첨가시까지 유전상수와 압전상수가 증가하였으나 첨가량이 그 이상 증가함에 따라 감소하였는데 이는 NiO가 소결조제 역할을 한 것으로 보여진다. 그러나 $1200^{\circ}C$ 이상 온도에서 소결한 시편에서는 NiO 첨가량 증가에 따라 유전상수와 전기기계결합계수가 감소하였으며, 기계적품질계수는 증가하였다. 경도 및 파괴인성은 1 mol% 첨가시 최대 값을 보이다가 그 이후 감소하였다. NiO 첨가 PNN-PT-PZ 세라믹스의 전기적 및 기계적 특성은 결정립크기, 소결밀도 및 2차상의 양 등의 미세구조적 요소와 긴밀한 관계가 있음을 보여준다. Dielectric properties, piezoelectric properties and mechanical properties of NiO-doped Pb($(Ni_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3$ ceramics were investigated. Powders, prepared by columbite precursor method, were cold pressed and sintered at temperature ranging from $1100^{\circ}C$ to $1250^{\circ}C$. Dielectric constant and piezoelectric constant increased with amount of NiO up to 1 mol% and then decreased with further addition of NiO. It seems that NiO acts as a sintering aid at the sintering temperatures of $1150^{\circ}C$. When the samples were sintered at temperature above $1200^{\circ}C$, however, both dielectric constant and electromechanical coupling factor decreased and mechanical quality coefficient increased with addition of NiO. Hardness and fracture toughness of PNN-PT-PZ increased with addition of NiO up to 1 mol%, and then decreased slightly with further addition of NiO. These results showed that dielectric properties, piezoelectric properties and mechanical properties of PNN-PT-PZ system seemed to be closely related with microstructural factors such as grain size, bulk density and the amount of second phase.

Tape Casting법에 의한 PMS-PZT계 세라믹스 제조 및 전기적 특성

정현제,나은상,최성철,Jung, Hyun-Jae,Na, Eun-Sang,Choi, Sung-Churl 한국세라믹학회 2001 한국세라믹학회지 Vol.38 No.9

본 논문은 출발물로서 2mol% CdO가 치환된 $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3$ 분말을 제조 후, 닥터 블레이드 방법으로 green sheet를 제조하기 위한 slurry의 최적 공정첨가제 조성에 관한 연구를 수행하였다. 또한, 제조된 green sheet에 대하여 소결 특성과 두께 변환에 따른 유전 및 압전 특성을 관찰하였다. 공정첨가제의 첨가에 따른 점도거동을 통하여 slurry를 최적화하였고, TGA 분석으로 소결조건을 정하였으며, sheet의 특성에 미세구조와 XRD 등으로 측정하였다. 최적의 slurry는 고형분량 30vol%에 대해 분산제 3.0wt%에서 가장 안정화되었고, 이후 바인더/가소제(0.75/0.25) 3.0wt% 첨가시 점도는 7.55Pa${\cdot}$s이었다. Green sheet의 유전 및 압전 특성들은 각각 900$^{\circ}$C, 950$^{\circ}$C, 1000$^{\circ}$C로 소결온도를 증가함에 따라 다소 증가하였지만, 두께에 따른 특성들은 큰 변화가 관찰되지 않음을 확인하였다. After manufacturing 2mol% CdO substitute $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.52}Ti_{0.48})O_3$ piezoelectric ceramics powder as starting material, to manufacture green sheets using Doctor Blade method. The optimum composition of slurry was studied. Moreover, the sintering properties and the dielectric and piezoelectric properties with variation a thickness of the manufactured sheets were investigated. The optimum of slurry was investigated by the rheology with addition of additives, the sintering condition was decided by TGA. And the properties of sheet were investigated through SEM. XRD. The optimum of slurry was the stablest at dispersant 3.0 wt% to solid loading 30vol%. After, at addition of binder/plasticizer(0.75/0.25) 3.0wt%, viscosity was 7.55Pa${\cdot}$s. The dielectric and piezoelectric properties of the sheet were increased a little with the increasing of sintering temperature but were not variable with variation of sheet thickness.

헤파린이 수근관 증후 군 환자의 횡수근 인대에서 추출한 섬유아세포의 콜라겐, MMP 및 TGF-β 동위형 발현에 미치는 영향

정성호,나민화,이재선,송상훈,윤을식,동은상,김한중 대한성형외과학회 2006 Archives of Plastic Surgery Vol.33 No.4

Purpose: Noninflammatory synovial fibrosis has been noted for main causal factor of carpal tunnel syndrome (CTS). Recently, there are some reports that heparin have not only anti-coagulative effect but also anti-inflammatory and anti-fibrotic potential and have an effect on interstitial pulmonary fiborosis. Authors examined whether heparin affects pathogenesis of CTS.Methods: First, heparin was administered to fibroblast that was cultured from patient's transverse carpal ligament. Secondly, we evaluated the expression from genes of type I, III collagen, TGF β isoforms and MMP. Fibroblasts were isolated and cultured from transverse carpal ligaments of 5 patients with CTS. Heparin (0, 1, 10,100μg/ml) was administered to cultured fibroblast and reverse transcription PCR for mRNA expression of type I, III collagen, TGF-β isoforms and MMP was done.Results: Heparin suppressed gene expression of type I, III collagen and TGF-β1, β3 but promoted gene expression of TGF-β2 and MMP-2.Conclusion: Heparin directly suppress gene expression of type I, III collagen. But, It is undetermined that heparin can present it's effect mediated by TGF β isoforms or MMP.

A Study on the Effect of Residual Stress between Body and Glaze of Pottery on the Mechanical Strength

이진하,나은상,최성철,Lee, Jin-Ha,Na, Eun-Sang,Choe, Seong-Cheol Materials Research Society of Korea 1999 한국재료학회지 Vol.9 No.2

In this study, the effect of residual stress on mechanical strength was investigated with 1 kind of whiteware body and 4 kinds of glazes which are produced in succeeding ceramic art place. Using dipping method, the body was coated for different times in order to manipulate the coating thickness and sintered in the different temperatures ($1200^{\circ}C$, $1250^{\circ}C$, $1300^{\circ}C$, $1350^{\circ}C$) for two thus hours. The sintered bodies were characterized by XRD, EPMA, FEM and UTM in order to study the forming of reaction layer between body and glazes, residual stresses and the effects of residual stresses on mechanical strength of pottery. At $1300{\circ}C$, we obtained maximum density and mechanical strength. By the finite element method, the residual stresses in surface of body were minimum in specific thickness of glazes and the mechanical strength of body in that thickness of glazes showed maximum when the firing temperature was settled.