이동식 크레인 하중이 굴착사면 안정성에 미치는 영향 분석

김정곤,나예지,원정훈,Kim, Jeong Kon,Na, Ye Ji,Won, Jeong-Hun 한국안전학회 2021 한국안전학회지 Vol.36 No.5

The effect of heavy construction equipment on the excavated slope is investigated by slope stability analysis. A mobile crane with 500 kN capacity is applied as a working load to the background surface of the excavated slope, in both sandy soil and clay, designed to guarantee the safety of slope stability. Major parameters such as the distance between the edge of the slope and the mobile crane, groundwater level, and ground plate size of the mobile crane are considered. Only 23.8% and 14.3% of the analysis models with sandy soil and clay excavated slope, respectively, satisfied the slope stability. By changing the slope of the sandy soil from 1:1.0 to 1:1.2, the number of analysis models securing slope stability increased from 23.8% to 40.5%. For the clay excavated slope, the analysis models securing slope stability increased from 14.3% to 42.9% by changing slope inclination from 1:0.8 to 1:1.2. In addition, it is found that the increase in the size of the ground plate of the mobile crane increases the analysis models that secure slope stability. Therefore, it is an effective way to relax the excavated slope's inclination angle and simultaneously increase the ground plate size to guarantee stability.

Stability Analysis of No.4 Slope in Maocaopo,Wushan County,Chongqing City

( Yang Tong ),( Men Yuming ) 대한지질공학회 2019 대한지질공학회 학술발표회논문집 Vol.2019 No.2

By collecting data, field exploration, indoor tests and using numerical simulation, this paper conducted in-depth study and analysis on the no.4 maocao slope, and the following conclusions are obtained: (1) Maocao No.4 Slope is located in the wuxia section of the three Gorges of theYangtze River, on the left bank of the main stream the Yangtze River. The area belongs to the landform area of eroded middle and low mountain valleys, and the slope angle 43~54°. The slope is a reversed slope with steep slopes. The potential landslide is bounded by two gullies. The trailing edge is bounded by the boundary platform of the bending deformation zone of the rock mass. The platform is about 13m wide, the trailing edge is 456m high, and the leading edge elevation is according to the terrain, it is 85m. The main factors affecting the stability of the slope include geological structure, reservoir water storage, rainfall, and human engineering activities. (2)Using the limit equilibrium method to calculate the overall stability of sliding slope stability of No.4 slope in Maocao slope, the results show that the sliding stability coefficient is greater than 1.15 under different working conditions. (3)Through the kajinqiu graphical method, it is predicted that the bank width above the 175m water level of the bank of No.4 of Maocao is 13.57 to 48.93m, and the upper boundary of the bank is 184.46 to 232.64m. The impact of the bank collapse is stronger and stronger in the area.

Research on Dynamic Evaluation Method of Slope Stability Based on Monitoring Data

( Xiaopeng Kang ),( Aijun Yao ),( Haifeng Guo ),( Jian Lu ) 대한지질공학회 2019 대한지질공학회 학술발표회논문집 Vol.2019 No.2

Due to the frequent occurrence of slope instability caused by disasters in recent years, it is particularly important for monitoring the slope disasters and the dynamic evaluation of slope stability. The monitioring data is the most intuitive factor to reflect the stability of the slope. Therefore, it is more urgent to directly evaluate the stability of the slope through the monitoring data of the slope disaster. In this paper, based on BP neural network, the slope s tability dynamic evaluation system-DESlopeStability is developed by MATLAB. Then, the accuracy of the DESlopeStability is verified by the numerical simulation of ABAQUS, which is a three-dimensional finite element software. Finally, this system is applied to the Jietai Temple landslide project in Beijing. Through the above research, the BP neural network can find the nonlinear mapping between the monitoring data and the stability coefficient of the slope based on a large amount of data, and the DESlopeStability system meets the actual engineering requirements and it can be used as an auxiliary means to judge the stability of the slope.

이종지질 분포사면에서의 3차원 사면안정해석

서용석 ( Yong Seok Seo ),이경미 ( Kyoung Mi Lee ),김광염 ( Kwang Yeom Kim ) 대한지질공학회 2011 지질공학 Vol.21 No.1

화강암과 안산암질 암맥이 공존하고 있는 붕괴사면을 대상으로 지질에 의한 전단강도의 차이를 반영한 3차원 사면안정해석을 수행하였다. 지질이 서로 다른 두 종류의 파괴면에 대한 전단강도를 파악하기 위하여 흙-암 경계면 직접전단시험을 수행하였고, 또한 상부 풍화토층에 대한 실내토질시험을 실시하였다. 시험결과 풍화토층에 비하여 흙-암 경계면의 전단강도가 낮게 나타났다. 사면내 지질분포의 차이가 안정성해석 결과에 영향을 주는 것을 알아보기 위하여 한계평형법을 이용한 2차원사면안정성 해석을 대표단면에서 실시하였으며, 사면내 분포지질에 따라 입력치를 다르게 할 수 있는 3차원사면안정성해석을 실시하여 2차원안정성해석과 그 결과를 비교하였다. 해석결과에 의하면 안전율이 건기시 0.92와 포화시 0.32로 모두 불안정하게 나타난 2차원해석결과와는 달리 3차원해석결과에서는 건기시에 안전율이 1.26, 포화시에 0.55로 나타났다. 이러한 결과는 사면내 지질분포를 고려할 경우 안정성 해석의 결과가 달라질 수 있음을 보여주고 있으며, 우기 직후 붕괴가 일어났던 점을 고려하면 3차원해석결과가 보다 현실적인 것으로 판단된다. Three-dimensional slope stability analysis was applied to a failed dual-lithology slope containing both granite and an andesitic dyke, taking account of the differences in shear strength of the different lithologies. A direct shear test of the soil-rock boundary was performed to examine the shear strength of two different types of failure surfaces within different lithologies, and a laboratory test was performed on an upper, weathered soil layer. The test results indicate that shear strength was lower at the soil-rock boundary than within the weathered soil layer. A representative geological section was subjected to two-dimensional slope stability analysis using a limit equilibrium method to assess whether the distribution of lithologies upon the slope influences the results of stability analysis. The results were then compared with those of three-dimensional slope stability analysis, for which input parameters can be varied according to the distribution of lithologies upon the slope. The three-dimensional analysis yielded safety factors of 1.26 under dry conditions and 0.55 under wet conditions, whereas the two-dimensional analysis yielded unstable safety factors of 0.92 and 0.32, respectively. These findings show that the results of stability analysis are affected by the distribution of different lithologies upon the slope. Given that the studied slope collapsed immediately after rainfall, it is likely that the results of the three-dimensional analysis are more reliable.

무한사면의 안정성에 미치는 억지말뚝의 영향에 대한 이론적 연구

이승현(Seung-Hyun Lee),이수형(Su-Hyung Lee) 한국산학기술학회 2016 한국산학기술학회논문지 Vol.17 No.12

억지말뚝으로 보강된 무한사면의 해석을 위해 억지말뚝에 작용하는 하중을 소성변형이론과 소성흐름이론을 적용하여 산정하였고 무한사면의 안전율에 영향을 미치는 다양한 인자들의 효과를 살펴보았다. 해석결과에 따르면 억지말뚝의 설치로 인해 사면의 안전율이 상당히 증가함을 알 수 있었고 말뚝설치간격이 커질수록 안전율은 감소하였다. 억지말뚝의 설치로 인한 안전율의 증가가 커서 무한사면의 침투발생 유무가 사면의 안전율에 미치는 영향은 상대적으로 미미할 것으로 생각된다. 억지말뚝으로 보강된 무한사면의 안전율을 수식으로 나타내 보았는데 무보강시 무한사면의 안전율에 영향을 미치는 흙의 강도정수 및 사면의 경사 그리고 사면의 두께 이외에도 무한사면요소의 폭과 길이 그리고 억지말뚝에 작용하는 하중에 영향을 받음을 알 수 있었다. 소성변형이론을 바탕으로 하여 억지말뚝보강 무한사면의 안전율을 흙의 강도정수를 달리하여 살펴본 결과 무보강시에 비해 상당한 안전율 증가효과를 확인할 수 있었는데 본 연구에서 고려한 강도정수와 말뚝간격에 대하여 최소 안전율은 13.7이었고 최대 안전율은 65.6이었다. 억지말뚝의 지름이 증가할수록 말뚝이 부담하는 하중은 증가하지만 안전율은 감소하였는데 이는 억지말뚝 보강 무한사면의 안전율에 영향을 미치는 무한사면요소의 폭과 길이 때문으로 판단된다. 소성흐름이론을 바탕으로 억지말뚝 보강 무한 사면의 안전율을 평균유입속도와 소성점도의 곱(υ₁ηp)을 달리하여 살펴본 결과 무보강시에 비해 상당한 안전율 증가효과를 확인할 수 있었으며 υ₁ηp값이 커질수록 안전율도 커짐을 알 수 있었고 일정한 υ₁ηp값에 대하여 말뚝설치간격이 커질수록 안전율은 감소하였다. To analyze an infinite slope that is reinforced with stabilizing piles, the forces on the stabilizing pile were estimated by the theory of plastic deformation and the theory of plastic flow and the effects of diverse factors on the factor of safety of an infinite slope were investigated. According to the results of the analyses, the factor of the safety of the slope reinforced with stabilized piles were increased tremendously and the factor of safety decreased as the center to center distance of the stabilizing pile increased. The effect of the existence of seepage of the infinite slope with stabilizing piles on the factor of safety appears to be insignificant. Considering the formulated factor of safety of an infinite slope with stabilizing piles, the width and length of the element of the infinite slope and force on the stabilizing pile influence the factor of safety of the infinite slope with a stabilizing pile including the soil strength parameter, inclination of the slope and depth of the slope, which are important for calculating the factor of safety of a non-reinforced infinite slope. The factor of safety of an infinite slope with stabilizing piles derived from the theory of plastic deformation were increased significantly with the internal friction angle of the soil, and the minimum and the maximum factor of safety under the conditions considered in this study were 13.7 and 65.6, respectively. As the diameter of the stabilizing pile increased, the forces on the stabilizing pile also increased but the factor of safety of the infinite slope with stabilizing piles decreased due to the effects of the width and the length of the element of the infinite slope. The factor of safety of the infinite slope with stabilizing piles derived from plastic flow were much larger than that of the non-reinforced infinite slope and the factor safety of the infinite slope with a stabilizing pile increased with increasing product of the flow velocity and plastic viscosity ( ) and the factor of safety of the infinite slope with stabilizing piles decreased with increasing center to center distance of the pile.

침투해석을 고려한 비탈면 설계에 대한 연구

김유성,김재홍,이진광,김성수 한국지반공학회 2013 한국지반공학회논문집 Vol.29 No.1

Most of slope failures are triggered by heavy rainfall during rainy season. If the rain keeps on for the season, the water content of the ground increases and its matric suction decrease, and then the safety factor of soil slope gets lower. The change of water table level for soil slope stability dose not describe the behavior of the soil slope in real situation,hence it may be necessary to modify the design standard for slope stability in association with rain infiltration. For correct design, economical construction, and maintenance of a soil slope, unsaturated flow analysis is needed for estimation of slope instability regarding water infiltration and soil behavior on unsaturated soil slopes. The entire soil slope cannot be saturated by prolonged rainfall and wetting band depth (saturated zone) just deepens from slope surface,hence the cause of the shallow surface slide is the wetting band depth depending on rainfall duration and intensity. Therefore, the paper presents the differences between theoretical equation and numerical analysis for wetting band depth on soil surface and its safety factor, and compares the slope stability obtained from unsaturated flow analysis with that obtained from conventional slope stability analysis.

억지말뚝을 이용한 점성토지반 절토사면의 설계

홍원표,한중근,송영석 한국지반공학회 1999 한국지반공학회논문집 Vol.15 No.5

본 연구에서는 억지말뚝을 이용한 점성토지반 절토사면에 대한 새로운 설계법이 제안된다. 이 설계법에서는 사면의 기울기와 높이, 억지말뚝열의 수와 설치위치, 말뚝의 간격과 강성 등의 요소를 체계적으로 선택할 수 있게 되어 있다. 이 설계법은 줄말뚝을 포함한 사면의 안정해석법에 근거하여 확립될 수 있다 말뚝으로 사면을 안정시킬 수 있는 기본적인 개념은 줄말뚝이 산사태와 같은 측방변형지반속에 설치되어 있을 경우 말뚝사이의 지반이 지반아칭현상에 의하여 억지 될 수 있다는데 있다. 줄말뚝을 포함한 사면의 전체안정을 검토하기 위하여 말뚝안정해석과 사면안정해석이 동시에 실시되어야 한다. 제안된 설계법에 따라 설계된 점성토지반 절토사면에 계측기를 설치하여 말뚝 및 말뚝사이 지반의 거동을 면밀히 관찰하였다. 이를 통하여 점성토지반 절토사면에 설치된 억지말뚝의 사면안정효과를 확인할 수 있었다. A new design technique is presented to stabilize cut slopes in cohesive soils by use of piles. The design method can consider systematically factors such as the gradient and height of slope, the number and position of pile's rows, the interval and stiffness of piles, etc. The design method is established on the basis of the stability analysis of slope with rows of piles. The basic concept applied in the stability analysis is that the soil across the open space between piles can be retained by the arching action of the soil, when a row of piles is installed in soil undergoing lateral movement such as landslides. To obtain the whole stability of slope containing piles, two kinds of analyses for the pile-stability and the slope- stability must be performed simultaneously. An instrumentation system has been installed at a cut slope in cohesive soil, which has been designed according to the presented design process. The behavior of both the piles and the soil across the open space between piles is observed precisely. The result of instrumentation shows that the cut slope has been stabilized by the contribution of stabilizing effect of piles on the slope stability in cohesive soil.

Evaluation of Slope Stability with Topography and Slope Stability Analysis Method

차경섭,김태훈 대한토목학회 2011 KSCE JOURNAL OF CIVIL ENGINEERING Vol.15 No.2

In existing researches connected with landslide, natural slope was regard as a parallel slope, but it was found that many landslides were occurred on the concave and convex slopes besides parallel slopes. This study was performed to evaluate the effect of shape and length of slope and soil depth for slope stability analysis and to compare infinite slope analysis with circular failure analysis for grid by grid analysis in prediction of GIS-based landslide hazard. As grid size is increased, average slope and curvature were decreased and the decreasing tendency was prominent in mountainous areas. Comparing infinite slope analysis and circular failure analysis for various degree of slope and soil depth, safety factor by infinite slope analysis is larger than that by circular failure analysis. Result showed that the factor safety depends on the shape of slope which is composed of two continuous slopes, if grid size is small (such as 5 m×5 m). So after due consideration for soil depth and topography, proper slope stability analysis must be performed.

셀 단위 평가법을 이용한 사면의 안정성 평가

장보안 ( Bo An Jang ),풍보현 ( Bo Hyun Poong ),장현식 ( Hyun Shic Jang ) 대한지질공학회 2008 지질공학 Vol.18 No.4

기존의 사면안정성 평가는 전체 사면을 균질하다고 가정하고 사면 내에서 가장 위험한 부분의 안정성으로 전체 사면의 안정성을 평가한다. 그러나 하나의 사면 내에서도 위치에 따라 암반/토사의 특성과 상태가 각각 다르기 때문에 기존의 평가방법으로 분석한 사면의 안정성이 전체 사면의 안정성을 대표한다고 할 수 없을 뿐만 아니라 사면의 보강에 있어서도 과도한 보강을 초래할 수 있다. 본 연구에서는 이 같은 문제를 해결하고자 하나의 사면을 격자형의 셀로 분할하여 각각의 셀의 특성을 조사하고 안정성을 평가하는 셀 단위 평가법을 제안하였다. 셀 단위 평가법에서는 사면을 구성물질에 따라 토사사면과 암반사면으로 구분하며, 각각의 셀에 대해 강도, 체적절리계수(Jv), 절리간격, 지하수상태, 절리상태 등을 조사하고 이를 SMR 및 상태지수를 통해 안정성을 평가한 후 셀 별 조사 자료와 안정성 분석결과를 종합하여 작성된 등고선도를 통해 사면의 위치별 안정성을 평가하게 된다. 본 연구에서는 총 3개의 사면에 대해 셀 단위 평가법을 적용한 결과 대부분의 셀에서 계산된 SMR 값은 기존의 평가법에서 구한 사면 전체의 SMR 값보다 높았다. 이는 셀 단위 평가법이 기존의 평가법 보다 사면을 보다 정확하게 평가할 수 있음을 의미하며, 기존의 사면 평가법이 가진 과도한 보강과 관련된 문제를 해결 할 수 있을 것이라 판단된다. When we evaluate slope stability, we regard the slope homogeneous and evaluate slope stability at the most dangerous portion of slope. However, since conditions and properties of rock mass/soil are different from one location to another within a single slope, slope stability evaluated by current concept can not represent slope correctly. This also result in over-reinforcement at the portion where reinforcement is not necessary. In order to solve these problems, we suggest a cell unit evaluation method in which we apply small rectangular cells in a slope and regard each cell as a single slope. In this method, slopes are classified into soil slope and rock slope depending on materials. Strength of rock, volumetric joint count, spacing of joints, condition of joints, ground water condition and so on are examined and SMR and condition index values are calculated. Finally, all data and results are presented as contour maps. We apply the cell unit evaluation method into 3 cut slopes. SMR values estimated by the new method are larger than those by current concept at most portions of slope, indicating that the new method suggested by this research represent slope stability more correctly than methods which were used. This method will prevent overreinforcement at the portion of slope where reinforcement is not necessary.

Numerical analysis on stability of express railway tunnel portal

Xiaojun Zhou,Hongyun Hu,Bo Jiang,Yuefeng Zhou,Yong Zhu 국제구조공학회 2016 Structural Engineering and Mechanics, An Int'l Jou Vol.57 No.1

On the basis of the geological conditions of high and steep mountainous slope on which an exit portal of an express railway tunnel with a bridge-tunnel combination is to be built, the composite structure of the exit portal with a bridge abutment of the bridge-tunnel combination is presented and the stability of the slope on which the express railway portal is to be built is analyzed using three dimensional (3D) numerical simulation in the paper. Comparison of the practicability for the reinforcement of slope with in-situ bored piles and diaphragm walls are performed so as to enhance the stability of the high and steep slope. The safety factor of the slope due to rockmass excavation both inside the exit portal and beneath the bridge abutment of the bridge-tunnel combination has been also derived using strength reduction technique. The obtained results show that post tunnel portal is a preferred structure to fit high and steep slope, and the surrounding rock around the exit portal of the tunnel on the high and steep mountainous slope remains stable when rockmass is excavated both from the inside of the exit portal and underneath the bridge abutment after the slope is reinforced with both bored piles and diaphragm walls. The stability of the high and steep slope is principally dominated by the shear stress state of the rockmass at the toe of the slope; the procedure of excavating rockmass in the foundation pit of the bridge abutment does not obviously affect the slope stability. In-situ bored piles are more effective in controlling the deformation of the abutment foundation pit in comparison with diaphragm walls and are used as a preferred retaining structure to uphold the stability of slope in respect of the lesser time, easier procedure and lower cost in the construction of the exit portal with bridge-tunnel combination on the high and steep mountainous slope. The results obtained from the numerical analysis in the paper can be used to guide the structural design and construction of express railway tunnel portal with bridge-tunnel combination on high and abrupt mountainous slope under similar situations.