http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
IN 738LC 합금의 미세조직 열화와 물성의 상관성 연구
유정훈,주성욱,신기삼,허성강,이재현,김의현,정진성,장성호,송기욱,하정수,Yoo Junghoon,Jo Sungwook,Shin Keesam,Hur Sungkang,Lee Je-Hyun,Kim Eui-Hyun,Jung Jine-sung,Chang Sungho,Song Geewook,Ha Jeongsoo 한국재료학회 2004 한국재료학회지 Vol.14 No.1
IN 738LC, the major material for gas-turbine for power generation, was heat treated at $750^{\circ}C$, $850^{\circ}C$, $950^{\circ}C$ for 1000, 2000, and 4000 hrs and the microstructural evolution and mechanical properties were examined using optical microscope, XRD, SEM/EDS. The results showed ${\gamma}$', the main strengthening elements in this alloy, was about 300 nm in size and was about 56% by area fraction in as-cast samples. The area fraction of ${\gamma}$' peaked at 2000 hours at $750^{\circ}C$. The average diameter of the ${\gamma}$' which was about 300 nm at ascast specimen increased to about 1 $\mu\textrm{m}$ after heat treatment at $950^{\circ}C$ for 4000 hrs. Carbides were formed at dendrite, cell or grain boundaries which was ascribed to the segregation caused by solute redistribution during solidification. It was found that MC type carbides formed at low temperature, whereas carbides of $M_{23}$ /$C_{ 6}$/ type formed at higher temperature or at longer degradation. The hardness and impact energy decreased as the heat treatment temperature or time of retention increased, which was inaccrodance with the area fraction of ${\gamma}$'.
이정훈(Junghoon Lee),유정훈(Jeonghoon Yoo) 대한기계학회 2008 大韓機械學會論文集A Vol.32 No.8
This paper is to suggest a concept design of the permanent magnet type magnetic resonance imaging (MRI) device based on the parameter optimization method. Pulse currents in the gradient coils will introduce the effect of eddy currents in the ferromagnetic material, which will worsen the quality of imaging. In order to equalize the magnetic flux in the MRI device for good imaging, the eddy current effect in the ferromagnetic material must be taken into account. This study attempts to use the design of experiment (DOE) and the response surface method (RSM) for equalizing the magnetic flux of the permanent magnet type MRI device using that the magnetic flux can be calculated directly using a commercial finite element analysis package. As a result, optimal shapes of the pole and the yoke of the PM type MRI device can be obtained. The commercial package, ANSYS, is used for analyzing the magnetic field problem and obtaining the resultant magnetic flux.
초초임계압 발전용 소재의 장시간 열처리에 따른 미세조직 변화와 기계적 특성의 상관관계 연구
주성욱,유정훈,신기삼,허성강,이재현,석진익,김정태,김병훈,Joo Sungwook,Yoo Junghoon,Shin Keesam,Hur Sung Kang,Lee Je-Hyun,Suk Jin Ik,Kim Jeong Tae,Kim Byung Hoon 한국재료학회 2005 한국재료학회지 Vol.15 No.1
For the good combination of high-temperature strength, toughness and creep property, $9-12\%$ chromium steels are often used for gas turbine compressors, steam turbine rotors, blade and casing. In this study, the correlation of microstructural evolution and mechanical properties was investigated fur the specimens heat-treated at 600, 650 and $700^{\circ}C$ for 1000, 3000 and 5000 hrs. The microstructure of as-received specimen was tempered martensite with a high dislocation density, small sub-grains and fine secondary phase such as $M_23C_6$. Aging for long-time at high temperature caused the growth of martensite lath and the decrease of dislocation density resulting in the decrease in strength. However, the evolution of secondary phases had influence on hardness, yield strength and impact property. In the group A specimen aged at $600^{\circ}C\;and\;650^{\circ}C$, Laves phase was observed. The Laves phase caused the increase of the hardness and the decrease of the impact property. In addition, the abrupt growth of secondary phases caused decrease of the impact property in both A and B group specimens.
Fe(II)EDTA 용액을 이용한 NO/SO₂ 가스의 동시저감 및 아연분말에 의한 용액 재생에 관한 연구
이강산(Kang-san Lee),장진영(Jinyoung Jang),박준수(Junsu Park),유정훈(Junghoon Yoo),최종원(Jongwon Choi) 대한설비공학회 2022 대한설비공학회 학술발표대회논문집 Vol.2022 No.6
Fe(II)EDTA 킬레이트 용액을 이용한 NOx 저감 기술은 용해도가 낮은 NO를 직접 흡착하여 상온에서 고효율 저감이 가능하다. 하지만 NO를 흡착한 Fe(II)EDTA는 더 이상 NO를 흡착할 수 있는 능력이 없으므로 이를 재생시켜 사용해야 된다. 최근 들어 금속이온을 이용하여 Fe(II)EDTA-NO를 환원시키는 연구가 많이 진행되고 있으며, 여러 금속이온 중 아연에 의한 용액 재생이 반응속도가 가장 빠르고, 경제적이라고 보고되었다. 따라서 본 연구에서는 Fe(II)EDTA 용액에 의한 NO/SO2를 동시저감 특성을 관찰하고, 아연분말에 의한 용액의 재생 특성을 용액의 pH에 따라 관찰하였다. 연구결과, pH가 낮을수록 Fe(II)EDTA가 Fe(III)EDTA로 쉽게 산화되어 NO 저감효율 및 흡착시간이 감소하였다. 하지만 pH5 이상 조건에서는 Zn(II)EDTA가 잘 형성되어 용액에 용해된 아연 이온을 석출하기가 어려워지므로 공정의 경제성을 위해서는 산성에 의한 장비부식이 일어나지 않도록 pH4.5~5이하 조건에서 운전하는 것이 타당하다고 판단된다.
Fe(II)EDTA 용액을 이용한 NO/SO₂ 가스의 동시저감 및 아연분말에 의한 용액 재생에 관한 연구
이강산(Kang-san Lee),장진영(Jinyoung Jang),박준수(Junsu Park),유정훈(Junghoon Yoo),최종원(Jongwon Choi) 대한설비공학회 2022 대한설비공학회 학술발표대회논문집 Vol.2022 No.6
Fe(II)EDTA 킬레이트 용액을 이용한 NOx 저감 기술은 용해도가 낮은 NO를 직접 흡착하여 상온에서 고효율 저감이 가능하다. 하지만 NO를 흡착한 Fe(II)EDTA는 더 이상 NO를 흡착할 수 있는 능력이 없으므로 이를 재생시켜 사용해야 된다. 최근 들어 금속이온을 이용하여 Fe(II)EDTA-NO를 환원시키는 연구가 많이 진행되고 있으며, 여러 금속이온 중 아연에 의한 용액 재생이 반응속도가 가장 빠르고, 경제적이라고 보고되었다. 따라서 본 연구에서는 Fe(II)EDTA 용액에 의한 NO/SO2를 동시저감 특성을 관찰하고, 아연분말에 의한 용액의 재생 특성을 용액의 pH에 따라 관찰하였다. 연구결과, pH가 낮을수록 Fe(II)EDTA가 Fe(III)EDTA로 쉽게 산화되어 NO 저감효율 및 흡착시간이 감소하였다. 하지만 pH5 이상 조건에서는 Zn(II)EDTA가 잘 형성되어 용액에 용해된 아연 이온을 석출하기가 어려워지므로 공정의 경제성을 위해서는 산성에 의한 장비부식이 일어나지 않도록 pH4.5~5이하 조건에서 운전하는 것이 타당하다고 판단된다.
Fe(II)EDTA 용액을 이용한 NO/SO₂ 가스의 동시저감 및 아연분말에 의한 용액 재생에 관한 연구
이강산(Kang-san Lee),장진영(Jinyoung Jang),박준수(Junsu Park),유정훈(Junghoon Yoo),최종원(Jongwon Choi) 대한설비공학회 2022 대한설비공학회 학술발표대회논문집 Vol.2022 No.6
Fe(II)EDTA 킬레이트 용액을 이용한 NOx 저감 기술은 용해도가 낮은 NO를 직접 흡착하여 상온에서 고효율 저감이 가능하다. 하지만 NO를 흡착한 Fe(II)EDTA는 더 이상 NO를 흡착할 수 있는 능력이 없으므로 이를 재생시켜 사용해야 된다. 최근 들어 금속이온을 이용하여 Fe(II)EDTA-NO를 환원시키는 연구가 많이 진행되고 있으며, 여러 금속이온 중 아연에 의한 용액 재생이 반응속도가 가장 빠르고, 경제적이라고 보고되었다. 따라서 본 연구에서는 Fe(II)EDTA 용액에 의한 NO/SO2를 동시저감 특성을 관찰하고, 아연분말에 의한 용액의 재생 특성을 용액의 pH에 따라 관찰하였다. 연구결과, pH가 낮을수록 Fe(II)EDTA가 Fe(III)EDTA로 쉽게 산화되어 NO 저감효율 및 흡착시간이 감소하였다. 하지만 pH5 이상 조건에서는 Zn(II)EDTA가 잘 형성되어 용액에 용해된 아연 이온을 석출하기가 어려워지므로 공정의 경제성을 위해서는 산성에 의한 장비부식이 일어나지 않도록 pH4.5~5이하 조건에서 운전하는 것이 타당하다고 판단된다.