http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
조동환,Jo, Dong-Hwan 대한치과기공사협회 1994 齒科技報 Vol.157 No.-
미수금 징수하여 사용하는 것은 바람직/제30차 종합학술대회/의료관계 행정처분 규칙제정/협회소식/지회소식/회무목적을 이루기 위한 효과적인 관리/치과기공사의 호흡기 증상과 폐환기능 검사화의 관계/건강한 치아를 오래 유지하는 요령/ 동정/보사부,의료용구 제조업소 시설조사기관 국립보건원 등 8개소 지정/
탄소섬유-페놀수지 및 안정화 PAN섬유-페놀수지 복합재료의 열주기 산화저항
조동환,안영석,이상철,윤관한,민병길,Jo, Dong-Hwan,An, Yeong-Seok,Lee, Sang-Cheol,Yun, Gwan-Han,Min, Byeong-Gil 한국재료학회 1997 한국재료학회지 Vol.7 No.10
폴리아크릴로나트릴(PAN)계 탄소섬유 및 안정화 PAN섬유를 사용하여 제조한 페놀수지 복합재료의 열주기 산화저항성에 섬유표면의 인산코팅 유.무가 미치는 영향을 조사하였다. 각 복합재료의 열주기 산화저항성은 열중량분석기의 원리를 응용하여, 공기중에서 hot zone과 cold zone을 주기적으로 반복이동하는 열충격조건에 노출되면서 초래되는 복합재료의 중량변화를 측정하여 비교하였다. 시험변수로는 hot zone에 노출된 온도, 시간 및 싸이클횟수를 선정하였다. 이 시험방법은 비교적 단순하며, 작은 크기의 시편으로도 가능하고, 중량변화가 온-라인 모니터에서 직접 감지되므로 데이타의 신뢰성이 \ulcorner다. 각 시험조건에서 인산코팅한 섬유를 사용한 복합재료가 그렇지 않은 재료보다 고온에서의 높은 산화저항성 때문에 우수한 열주기저항성을 보여 주었다. 또한 인산코팅의 존재 여부가 열주기시험 후의 탄소섬유-페놀수지 및 안정화 PAN섬유-페놀수지 복합재료의 미세구조에 미치는 영향을 조사하였다.
자동 사진 측광기의 성능 검사와 성단 BYUR 2의 측광
조동환,이시우,이현곤,Jo, Dong-Hwan,Lee, Si-U,Lee, Hyeon-Gon 한국천문학회 1993 天文學論叢 Vol.8 No.1
The Automated Eichner Iris Photometer(AEIP) at the Korea Basic Science Center was tested for its function and the proper procedure for photographic photometry. The AEIP requires about three hours for reaching the electrical stability. When the iris is controlled automatically, the repeatability of density unit (DU) is accurate in the uncertainty of ($0.0028{\sim}0.0048$)DU. The iris reading is found to be accurate within the mean error of $0.^{m}05$, which could be reduced to $0.^{m}02$ by the manual control. To check the applicability of the AEIP. each two photographic plates for UBV colors which were taken by Dupuy and Zukauskas(l976) for the open cluster Byur 2, were measured by using the AEIP. and the photographic magnitudes and colors of the stars in Byur 2 were determined. discussing the previous results.
인산코팅된 OXI-PAN 섬유/페놀수지 복합재료의 물리적특성과 미세구조에 미치는 열처리온도의 영향
조동환,Jo, Dong-Hwan 한국재료학회 1996 한국재료학회지 Vol.6 No.10
본 연구에서는 인산코팅된 것과 되지 않은 OXI-PAN섬유를 사용하여 제조된 무질서 배향의 OXI-PAN/페놀수지 복합재료를 불활성분위기의 여러 열처리온도에서 탄화하였을 때, 섬유표면에 인화합물의 존재 유.무가 복합재료의 물리적특성 및 미세구조 변화에 미치는 영향을 조사하였다. 두 종류 복합재료의 물리적특성 변화를 탄화온도 영향에 대한 섬유와 매트릭스 및 그 계면에서의 미세구조 거동변화와 기공형성의 관점에서 해석하였다. 열처리시 온도상승에 따라 섬유와 매트릭스 계면에서의 화학반응에 의해서 그 구분이 점차 사라지면서 국부적으로 치밀하고 균일한 상을 이루고 있는 것으로 조사되었다. 또한, 탄화 조건에서도 인산코팅은 OXI-PAN 섬유의 직경의 감소를 억제하고 열안정성을 향상시키므로 복합재료의 부피수축률을 줄이고 탄화수율을 증가시키는데도 어느정도 기여할 수 있으리라 판단되었다.
탄화복합재료 함침을 위한 퍼퓨릴알콜/흑연분말 혼합물의 열안정성
안영석,조동환,An, Yeong-Seok,Jo, Dong-Hwan 한국재료학회 1998 한국재료학회지 Vol.8 No.4
탄소섬유강화 탄소복합재료를 구성하는 탄소매트릭스 프리커서로서 또는 함침제로서 사용되는 퍼퓨릴알콜의 열안전성과 탄소수율에 $2000^{\circ}C$에서 열처리한 흑연분말과 함침 후 경화시 승온속도가 미치는 영향을 열분석방법을 이용하여 조사하였다. 퍼퓨릴알콜에 30wt%의 흑연분말을 첨가하였을 때와 동시에 승온속도가 분당 $35^{\circ}C$일 때 퍼퓨릴알콜/흑연분말 혼합물은 가장 높은 열안정성을 보여주었으며, 흑연분말을 사용하지 않은 경우보다 $1000^{\circ}C$이상에서의 탄소수율이 10%이상 향상되었다. 이러한 결과는 탄소복합재료의 밀도화에 수반되는 탄화$\longrightarrow$함침$\longrightarrow$경화$\longrightarrow$재탄화 반복공정의 횟수를 줄이는데 다소 기여할 것으로 판단되었다. We examined, using thermoanalytical methods, the effects of $2000^{\circ}C$ heat-treated graphite powders and heating rate of cure after impregnation on the thermal stability and carbon yield of furfuryl alcohol, which is frequently used not only as an impregnant but also as a matrix precursor for carbon fiber-reinforced carbon composites. It was founded that the addition of 30wt% graphite powders to furfuryl alcohol and the heating rate of $35^{\circ}C$/min showed the highest thermal stability of furfuryl alcohol/graphite powder mixture. The carbon yield above $1000^{\circ}C$ was enhanced more than 10% in comparison with the absence of graphite powders. It would be expected that this result can contribute to some extent to reduce the repeating number of processing cycle (carbonization-impregnation-cure-re-carbonization) required to densify a carbonaceous composite.
실험계획법을 이용한 탄소섬유/페놀수지의 강화 cycle연구
하헌승,이진용,조동환,윤병일,Ha, Heon-Seung,Lee, Jin-Yong,Jo, Dong-Hwan,Yun, Byeong-Il 한국재료학회 1993 한국재료학회지 Vol.3 No.5
다구찌의 실험계획기법을 이용하여 탄소섬유/페놀수지의 결화싸이클을 연구하였다. 본 연구에서는 1인자 2수준과 7인자 3수준으로 구성된 $L_{18}(2^1 \times 3_7)$ 직교배열표를 사용하였고, 특성치로 굴곡강도와 기공률을 선정하여 실험하였다. 실험계획법의 압축성형 인자로는 8개의 성형인자(승온속도, 가압온도, 성형압력, 경화온도, 경화온도에서의 유지시간, 냉각속도 및 탈기포)가 고려되었으며, 이들 성형인자가 탄소섬유/페놀수지 복합재료의 물성에 미치는 영향을 고찰하였다. 분산분석법으로 실험결과를 분석한 결과, 탄소섬유/패놀수지 복합재료의 굴곡강도에 가장 큰 영향을 미치는 성형인자는 성형압력이고, 기공률에 가장 큰 영향을 미치는 성형인자는 경화온도임이 밝혀졌다. In this paper the cure cycle of carbon fiber/phenolic resin was investigated by the Taguchi Method in an experimental design. Experiments were systematically performed using $L_{18}(2^1 \times 3_7)$ orthorgonal array table of the experimental design. In the experimental design, eight compression molding parameters (heating rate, pressing temperature, pressing rate, molding pressure, curing temperature, dwell time at curing temperature, cooling rate and degassing) were considered and the effects of the parameters on the flexural strength and the apparent porosity of carbon fiber/phenolic composites were investigated. The analysis of variance for the experimental results indicated that molding pressure and curing temperature are the most significant parmeters in the flexural strength and the apparent porosity of carbon fiber/phenolic resin composites, respectively.
비골 골절 교정술 후 "Tubed Merocel"과 골무를 이용한 비충전
조동환,김경목,이영섭 大韓成形外科學會 1997 Archives of Plastic Surgery Vol.24 No.5
Post-operative nasal packing is used almost universally following routine closed reduction of fractured nasal bone. But it is often considered by the patient to be one of the most unpleasant aspects of their operation. It is difficult for the patients to continue keeping nasal pack for more than a week especially for their breathing problem. In addition, nasal packing can precipitate hypoxia and obstructive sleep apnea, particularly in older patients, headache, foul odor and other problems. The Merocel which contains airway is thought to avoid some of these hazards. These packs or tampons with airway are constructed from a foam polymer of hydroxylated polyvinyl acetate and central tube. When the packs are moistened with secretioris or aqueous solutions they swell up to about 4.8 times of their original size, secure nasal patency and optimal pressure for hemostasis and stability of the reduced nasal bone. Nasal packing by using tubed Merocel and finger stall is comfortable to the patients after nasal bone reduction.