포화상태에 놓인 C-Type 액체수소 탱크의 슬로싱이 열 유속과 BOG에 미치는 변화의 수치적 분석

이진호,황세윤,이성제,이장현,Lee, Jin-Ho,Hwang, Se-Yun,Lee, Sung-Je,Lee, Jang Hyun 한국전산구조공학회 2022 한국전산구조공학회논문집 Vol.35 No.5

본 논문은 슬로싱 상태에 놓인 포화 상태 액체수소탱크에서 열 유속 및 BOG(Boil-off gas)의 경향을 다루고 있다. 특히, 액체-기체간의 침투 및 혼합에 의한 열 교환에 관심을 두었다. 먼저, VOF(Volume of fluid)와 Eulerian 기반의 다상 유동모델로 모형 슬로싱 실험을 모사하여 압력을 예측하고 계측된 값과 비교하였다. 자유 수면 및 충격 압력 실험 결과와 해석 결과를 비교하였으며, 유체의 속도 예측에서 정확할 수 있음을 간접적으로 증명하였다. 그리고 2차원의 Type-C 원통형 수소탱크를 대상으로 다상열유동해석을 수행하였다. 이때 포화상태에 놓인 액체 및 기체수소를 가정하고, 해석을 통해 각 상간의 혼합에 의한 열 교환의 수준을 확인하고자 하였다. 단, 상간의 열 교환만을 관심으로 두고 있었으므로 질량전달 및 기화모델은 해석에서 제외하였다. 최종적으로 상의 혼합으로 인해 액체수소로 유입되는 열 유속의 기여도에 대하여 정리하였다. 또한 액체수소로 유입되는 열 유속과 집중 질량 기반의 간이식을 통해 BOG 발생량 및 경향을 예측하고 분석하였다. This study was conducted to predict the tendency for heat exchange and boil-off gas (BOG) in a liquefied hydrogen tank under sloshing excitation. First, athe fluid domain excited by sloshing was modeled using a multiphase-thermal flow domain in which liquid hydrogen and hydrogen gas are in the saturated state. Both the the volume of fluid (VOF) and Eulerian-based multi-phase flow methods were applied to validate the accuracy of the pressure prediction. Second, it was indirectly shown that the fluid velocity prediction could be accurate by comparing the free surface and impact pressure from the computational fluid dynamics with those from the experimental results. Thereafter, the heat ingress from the external convective heat flux was reflected on the outer surfaces of the hydrogen tank. Eulerian-based multiphase-heat flow analysis was performed for a two-dimensional Type-C cylindrical hydrogen tank under rotational sloshing motion, and an inflation technique was applied to transform the fluid domain into a computational grid model. The heat exchange and heat flux in the hydrogen liquid-gas mixture were calculated throughout the analysis,, whereas the mass transfer and vaporization models were excluded to account for the pure heat exchange between the liquid and gas in the saturated state. In addition, forced convective heat transfer by sloshing on the inner wall of the tank was not reflected so that the heat exchange in the multiphase flow of liquid and gas could only be considered. Finally, the effect of sloshing on the amount of heat exchange between liquid and gas hydrogen was discussed. Considering the heat ingress into liquid hydrogen according to the presence/absence of a sloshing excitation, the amount of heat flux and BOG were discussed for each filling ratio.

접지면 위 도선에 대한 고고도 전자기 펄스 신호의 결합 특성 분석

이진호,권준혁,신규범,강래충,Lee, Jin-Ho,Kwon, Joon-Hyuck,Shin, Guy-Beom,Kang, Rae-Choong 한국군사과학기술학회 2010 한국군사과학기술학회지 Vol.13 No.6

Since HEMP has the very short rising time and propagates widespreadly with several tens of kV/m, it threatens most of systems in its cover range. Therefore, it is important to research coupling mechanism into systems and establish countermeasures for the HEMP to protect systems effectively. This paper analyzed characteristics and trends of currents to be induced at the load of a line which is located over ground with different conditions such as polarization, incidence angle, line length and height etc. We applied double exponential waveform as the HEMP shape and used BLT method to analyze the coupling route into the line. Also, we compared the simulation data of chain matrix modeling to verify reliability of BLT modeling. In the result, two data is almost agreed.

K-7소음총의 사격음 특성에 대한 실험적 연구

이진호,Lee Jin-Ho 한국군사과학기술학회 2004 한국군사과학기술학회지 Vol.7 No.4

In 1909 Hiram P. Maxim invented one of the first metal silencers for reducing sound levels in firearms. Silenced me have been mainly applied in the hunting and military operation. In particular special force make use of silenced rifle because it is low sound level. This paper considers experimental analysis for the characteristics of shock wave caused by shooting of a silenced me. Experimental results Indicate that the sound level of K-7 silenced rifle was lower than the sound level of MP5 silenced rifle. And, Sound Power Level of K-7 silenced rifle at a distance more than 75m or loom have nearly the constant value. This results that suggested the characteristics data about K-7 rifle's impulse noise will be apply to design the silencer of a small arms.

상호 변조 및 불요 신호에 대한 탐색레이더 부 체계의 EMI 시험 기법

이진호,Lee, Jin-Ho 한국군사과학기술학회 2007 한국군사과학기술학회지 Vol.10 No.2

MIL-STD-461E, EMI military standard for the equipment and subsystems, requires reception characteristic tests to verify the susceptibility of a receiver against the jntermodulation and spurious signals. Because the CS103 and CS104 of MIL-STD-461E show the test configuration of the equipment unit like a traditional receiver, it is possible to verify the susceptibility only for the reception signal through analog filters. However, at present when software programming techniques make a progress, the CS103 and CS104 tests need to evaluate the reception signal of the subsystem which includes both the digital filtering effects and analog filter characteristics. These test and evaluation techniques applied to a surveillance radar subsystem. This paper researched the EMI test methods in order to confirm feasibility of these test and evaluation techniques. Also the test results are compared and analyzed.

K2소총의 사격음 차폐장치에 관한 실험적 연구

이진호,Lee, Jin-Ho 한국군사과학기술학회 2010 한국군사과학기술학회지 Vol.13 No.3

This paper studies an experimental analysis of the impulse noise of K2 rifle when its bullet passes through the large tube(length 1.84m, outer diameter 50cm, glass wool & steel). In experiment, the characteristics of the sound of shooting were different according to the way of shooting; the results of the experiment are given below. First of all, the shooting sound was lower in single-shot shooting, when compared to 3rds burst-shot shooting, difference averaging 2.8dB, 4.0dB at maximum. In short, the difference is minuscule. Secondly, the sound of the K2 rifle was diminished when shot in a tube, ranging from 2.7dB to 15.4dB, averaging 8.2dB. Thirdly, the shooting sound of the K2 rifle was diminished as the insertion depth deepened with formulas given in Fig. 5, 6. Fourthly, basic data for excluding sound of the shooting were presented. Lastly, the characteristics of the shooting sound could be equally used as a basic material for developing marksmanship and sharp-shooting detection device.

다층 대공방어 체계의 신뢰도 향상을 위한 네트워크 모델 기반의 최적 투자 계획 모델

이진호,정석문,Lee, Jinho,Chung, Suk-Moon 한국시뮬레이션학회 2017 한국시뮬레이션학회 논문지 Vol.26 No.3

This study considers an optimal investment planning for improving survivability from an air threat in the layered air defense system. To establish an optimization model, we first represent the layered air defense system as a network model, and then, present two optimization models minimizing the failure probability of counteracting an air threat subject to budget limitation, in which one deals with whether to invest and the other enables continuous investment on the subset of nodes. Nonlinear objective functions are linearized using log function, and we suggest dynamic programming algorithm and linear programing for solving the proposed models. After designing a layered air defense system based on a virtual scenario, we solve the two optimization problems and analyze the corresponding optimal solutions. This provides necessity and an approach for an effective investment planning of the layered air defense system. 본 연구는 대공위협에 대한 생존성 향상을 위한 다층 대공방어 체계의 최적 투자 계획 모델을 고려한다. 최적화 모델 수립을 위해 다층 대공방어 체계를 네트워크 모델로 표현하고, 가용 예산이 제한되어 있는 상황 하에서 대응실패 확률을 최소화하기 위해 각 방어무기에 대하여 투자여부를 결정하는 모델과 연속적인 투자가 가능한 모델을 각각 제시한다. 비선형 형태의 목적함수를 로그함수를 통해 선형화하였으며, 제시된 최종 모델의 해법으로서 동적계획법 알고리즘과 선형계획법을 제안한다. 가상의 다층 대공 방어 상황을 설정한 후, 두 가지의 최적화 모델에 대한 최적해를 도출하고 그 결과를 분석하였다. 이는 다층 대공방어 체계의 신뢰도 향상을 위한 효과적인 투자 계획 수립의 필요성 및 접근방법을 제시한다.

PCB의 최근기술동향

이진호,Lee, Jin-Ho 한국전자정보통신산업진흥회 1997 電子振興 Vol.17 No.3

무선 센서 네트워크 환경에서의 에너지 효율성을 고려한 태스크 스케줄링 기법

이진호,최훈,백윤주,Lee Jin-Ho,Choi Hoon,Baek Yun-Ju 한국통신학회 2006 韓國通信學會論文誌 Vol.31 No.9A

무선 센서 네트워크에서의 센서 노드는 배터리로 동작하기 때문에 에너지에 대한 제약이 있다. 따라서 무선 센서 노드를 위한 효율적인 전력 관리 기법과 스케줄링 기법 설계가 중요한데, 본 논문에서는 운영체제 레벨의 소비 에너지를 줄이기 위한 알고리즘을 제안한다. 효율적인 배터리 사용을 위해 상황에 따라 필요한 컴포넌트에만 전원을 인가함으로써 센서노드의 에너지 소비를 줄일 수 있다. 본 논문에서는 제안한 알고리즘을 시뮬레이션 한 결과 기존의 duty 사이클과 비교하여 최대 56%의 에너지가 절약되었음을 알 수 있다. A wireless sensor node is typically battery operated and energy constrained. Therefore it is critical to design efficient power management technique and scheduling technique. In this paper, we propose an OS-level power management technique for energy saving of wireless sensor node, it is called EA-SENTAS (Energy-Aware Sensor Node TAsk Scheduling). It can decrease the energy consumption of a wireless sensor node to use task scheduling technique that shut down components or use low power mode of each component when not needed. Simulation results show that EA-SENTAS saves energy up to 56 percent to compare with conventional duty cycle.

3차원 채널 밑면에 탑재된 모듈로부터의 혼합대류열전달

이진호,박상희,유갑종,방창훈,Lee, Jin-Ho,Park, Sang-Hee,Riu, Kap-Jong,Bang, Chang-Hoon 대한기계학회 2000 大韓機械學會論文集B Vol.24 No.5

Conjugate heat transfer from a heat generating module ($31{\times}31{\times}7mm^3$) bonded through the module support on the floor of a parallel-plate channel(20mm high, 400mm wide, and 800mm long) to mixed convective air flow(0.2${\sim}$0.9m/s) is studied experimentally. The input power to the module is changed in a range 1.0${\sim}$4.5W, the floor thickness 0.2${\sim}$5mm, and the thermal resistance of module support, Rc:=0.06, 1.03 and 82.0K/W. Thermal conductance(Uc) of the board and convective thermal conductance($U_A$) from the module were derived, and the effect of V; Rc and t on Uc was investigated. It is found that the conjugate conductance (Uc) and the conductive heat transfer ratio ($Q_B$/Q) depend on the thermal resistance of the module support, the air velocity and the board thickness. The change of the module support resistance and the board thickness helps to elucidate the relative significance of heat transfer paths through the module support, the board, and from the board surface to the air. Additional information is investigated about the dependence of the heat transfer rate on the mixed convection parameter.

분할된 $AB^2$ 시스톨릭 모듈러 곱셈기 설계

이진호,김현성,Lee, Jin-Ho,Kim, Hyun-Sung 한국통신학회 2006 韓國通信學會論文誌 Vol.31 No.1c

[ $AB^2$ ]연산은 공개키 암호화 시스템을 위한 효율적인 기본 연산으로 알려져 있고 이를 위한 다양한 하드웨어가 설계되었다. 그러나 이들 구조들은 암호학적 응용에 사용되기에는 구조복잡도가 크다는 문제점이 있었다. 본 논문에서는 GF($2^m$)상에서 공간 효율적인 분할된 $AB^2$ 시스톨릭 모듈러 곱셈기를 설계한다. MSB $AB^2$ 모듈러 곱셈 알고리즘으로부터 데이터 의존 그래프를 유도하고 유도된 의존 그래프를 1/3로 분할함으로서 공간 효율적인 분할된 $AB^2$ 시스톨릭 곱셈기를 설계한다. 본 논문에서 제안한 곱셈기는 기존의 곱셈기와 비교하여 2/3정도의 구조 복잡도를 줄일 수 있다. 본 논문에서 제안한 구조는 크기에 제한을 갖는 스마트 카드 등에서 사용될 공개키 암호의 핵심이 되는 지수기의 구현을 위한 효율적인 기본구조로 사용될 수 있을 것이다. An $AB^2$ modular operation is an efficient basic operation for the public key cryptosystems and various systolic architectures for $AB^2$ modular operation have been proposed. However, these architectures have a shortcoming for cryptographic applications due to their high area complexity. Accordingly, this paper presents an partitioned $AB^2$ systolic modular multiplier over GF($2^m$). A dependency graph from the MSB $AB^2$ modular multiplication algorithm is partitioned into 1/3 to get an partitioned $AB^2$ systolic multiplier. The multiplier reduces the area complexity about 2/3 compared with the previous multiplier. The multiplier could be used as a basic building block to implement the modular exponentiation for the public key cryptosystems based on smartcard which has a restricted hardware requirements.