저층트롤의 발줄 및 저질의 종류에 따른 정항특성

신정욱 ( Jung Wook Shin ),이주희 ( Ju Hee Lee ),권병국 ( Byeong Guk Kwon ) 한국어업기술학회 2002 수산해양기술연구 Vol.38 No.1

Dosimetric Influence of Implanted Gold Markers in Proton Therapy for Prostate Cancer

곽정원,신정욱,김진성,박성용,신동호,윤명근,박소아,김동욱,임영경,이세병,Kwak, Jung-Won,Shin, Jung-Wook,Kim, Jin-Sung,Park, Sung-Yong,Shin, Dong-Ho,Yoon, Myong-Geun,Park, So-Ah,Kim, Dong-Wook,Lim, Young-Gyeung,Lee, Se-Byeong Korean Society of Medical Physics 2010 의학물리 Vol.21 No.3

본 연구에서는 양성자 치료에서 치료부위에 금 마커를 삽입하였을 때 양성자 빔의 선량과 그 분포에 미치는 영향을 평가하였다. 1.2 mm 직경에 3 mm 길이의 원통형 금 마커가 사용되었고 양성자 빔의 여러 위치에서 각각의 선량에 미치는 영향을 조사하였다. 3차원 moving 팬텀과 유효 반경이 0.5 mm인 정위적 방사선 치료용 다이로드 검출기를 이용하여 금마커의 방사선 선량으로의 영향을 결정하였다. Gafchromic film을 이용한 필름에 의한 선량 평가도 시행하였다. 그리고 선량-체적관계 히스토그램을 통한 분석을 위하여 GEANT4 전산 모의 도구 모음을 이용한 전산모의를 실시하였다. 마커의 움직임에 대한 영향성을 평가하기 위하여 직장 풍선을 적용하고 금 마커를 삽입한 10명의 환자에 대한 MV 영상을 이용하였다. 하나의 금 마커에 의하여 처방선량의 95% 이하가 들어간 체적은 0.15 cc로 작지만 그 체적은 치료부위 안쪽에 위치하고 평행이동에 대하여 발려져서 없어지지 않았다. 금 마커의 위치와 양성자 빔의 상태에 따라서 선량분포에 각각 다른 영향을 미치고 이는 임상치료에서 충분히 고려되어야 할 것으로 사료된다. This study examined the dosimetric influence of implanted gold markers in proton therapy and the effects of their positions in the spread-out Bragg peak (SOBP) proton beam. The implanted cylindrical gold markers were 3 mm long and 1.2 mm in diameter. The dosimetric influence of the gold markers was determined with markers at various locations in a proton-beam field. Spatial dose distributions were measured using a three-dimensional moving water phantom and a stereotactic diode detector with an effective diameter of 0.5 mm. Also, a film dosimetry was performed using Gafchromic External Beam Treatment (EBT) film. The GEANT4 simulation toolkit was used for Monte-Carlo simulations to confirm the measurements and to construct the dose-volume histogram with implanting markers. Motion data were obtained from the portal images of 10 patients to investigate the effect of organ motions on the dosimetric influence of markers in the presence of a rectal balloon. The underdosed volume due to a single gold marker, in which the dose was less than 95% of a prescribed amount, was 0.15 cc. The underdosed volume due to the presence of a gold marker is much smaller than the target volume. However, the underdosed volume is inside the gross tumor volume and is not smeared out due to translational prostate motions. The positions of gold markers and the conditions of the proton-beam field give different impacts on the dose distribution of a target with implanted gold markers, and should be considered in all clinical proton-based therapies.

신증후군 환자에서 스테로이드 충격요법과 경구용 면역억제제 치료 중 발생한 가역성 후백질뇌병증 1례

서주희,신정욱,김지홍,윤춘식,Seo Joo Hee,Shin Jung Wook,Kim Ji Hong,Yoon Choon Sik 대한소아신장학회 2005 Childhood kidney diseases Vol.9 No.2

저자들은 정맥 주사용 스테로이드 충격요법과 경구 cyclophosphamide 치료를 받던 신증후군 환아에서 가역성 후백질뇌병증 1례를 경험하였기에 문헌 고찰과 함께 보고하는 바이다. The syndrome of reversible posterior leukoencephalopathy syndrome(RPLS) is characterized clinically by acute neurologic signs such as headache, vomiting, confusion, seizures, and visual abnormalities. Radiologically, abnormalities consistent with reversible white matter edema in the occipital and parietal lobes are characteristic. RPLS has often been associated with various systemic disorders, such as hypertensive encefhalopathy, eclampsia, and the use of intravenous or intrathecal immunosuppressive drugs. We report a case of RPLS that occurred after intravenous steroid pulse therapy and treatment with oral cyclophosphamide in a child with nephrotic syndrome, and we emphasize the importance of early recognition of RPLS in the treatment of nephrotic syndrome and appropriate management tn prevent Permanent neurologic disability. (J Korean Soc Pediatr Nephrol 2005;9:245-250)

복강경 수술로봇을 위한 실시간 운영체제 기반 제어 시스템의 개발

송승준,박준우,신정욱,김윤호,이덕희,조영호,최재순,선경,Song, Seung-Joon,Park, Jun-Woo,Shin, Jung-Wook,Kim, Yun-Ho,Lee, Duk-Hee,Jo, Yung-Ho,Choi, Jae-Seoon,Sun, Kyung 대한의용생체공학회 2008 의공학회지 Vol.29 No.1

This paper reports on a realtime OS based master-slave configuration robot control system for laparoscopic surgery robot which enables telesurgery and overcomes shortcomings with conventional laparoscopic surgery. Surgery robot system requires control system that can process large volume information such as medical image data and video signal from endoscope in real-time manner, as well as precisely control the robot with high reliability. To meet the complex requirements, the use of high-level real-time OS (Operating System) in surgery robot controller is a must, which is as common as in many of modem robot controllers that adopt real-time OS as a base system software on which specific functional modules are implemened for more reliable and stable system. The control system consists of joint controllers, host controllers, and user interface units. The robot features a compact slave robot with 5 DOF (Degree-Of-Freedom) expanding the workspace of each tool and increasing the number of tools operating simultaneously. Each master, slave and Gill (Graphical User Interface) host runs a dedicated RTOS (Real-time OS), RTLinux-Pro (FSMLabs Inc., U.S.A.) on which functional modules such as motion control, communication, video signal integration and etc, are implemented, and all the hosts are in a gigabit Ethernet network for inter-host communication. Each master and slave controller set has a dedicated CAN (Controller Area Network) channel for control and monitoring signal communication with the joint controllers. Total 4 pairs of the master/slave manipulators as current are controlled by one host controller. The system showed satisfactory performance in both position control precision and master-slave motion synchronization in both bench test and animal experiment, and is now under further development for better safety and control fidelity for clinically applicable prototype.

양성자 치료 전산모사를 위한 Geant4 전자기 물리 모델 정확성 검증

박소현,라정은,신정욱,박성용,윤세철,정원균,서태석,Park, So-Hyun,Rah, Jeong-Eun,Shin, Jung-Wook,Park, Sung-Yong,Yoon, Sei-Chul,Jung, Won-Gyun,Suh, Tae-Suk 한국의학물리학회 2009 의학물리 Vol.20 No.4

Geant4 toolkit은 전자기적 상호작용(electromagnetic interactions)에 대한 다양한 물리적 모델을 제공한다. 이러한 물리적 모델들에 대한 검증은 신뢰성 있는 Geant4 응용을 위해서 중요한 역할을 한다. 그러므로, 본 연구의 목적은 양성자 치료 전산모사를 위해 Geant4가 제공하는 물리적 모델 중 전자기 물리 모델의 정확성을 검증하는 것이다. 검증은 물, 뼈, 지방 그리고 원자번호가 다른 물질에 대해 양성자의 CSDA 비정(continuous slowing down approximation range)과 저지능(stopping power) 데이터를 미국 국립기술표준원(National Institute of Standards and Technology, NIST)의 데이터를 각각 비교하는 방법으로 이루어졌다. 물, 뼈 그리고 지방에 대해 0.01 MeV에서 10 GeV 범위의 입사 에너지의 CSDA 비정과 저지능 전산모사 결과와 NIST값을 비교한 결과, CSDA 비정의 평균 차는 각각 1.0%, 1.4% 그리고 1.4%를 나타내었고, 저지능에 대한 평균 차는 각각 0.7%, 1.0% 그리고 1.3%를 나타내었다. 또한, 각 물질에 대한 NIST 값과의 유의성을 분석하기 위해 kolmogorov-smirnov Goodness-of-Fit 통계분석 방법을 이용한 결과, 전자기 물리 모델의 전산모사 결과 데이터와 NIST 데이터 사이의 유의성을 나타내는 p-value가 유의 수준 0.05 이상 값을 가진다는 것을 확인 하였으며, 이를 통해 Geant4 전자기 물리 모델의 정확성을 검증할 수 있었다. Geant4 (GEometry ANd Tracking) provides various packages specialized in modeling electromagnetic interactions. The validation of Geant4 physics models is a significant issue for the applications of Geant4 based simulation in medical physics. The purpose of this study is to evaluate accuracy of Geant4 electromagnetic physics for proton therapy. The validation was performed both the Continuous slowing down approximation (CSDA) range and the stopping power. In each test, the reliability of the electromagnetic models in a selected group of materials was evaluated such as water, bone, adipose tissue and various atomic elements. Results of Geant4 simulation were compared with the National Institute of Standards and Technology (NIST) reference data. As results of comparison about water, bone and adipose tissue, average percent difference of CSDA range were presented 1.0%, 1.4% and 1.4%, respectively. Average percent difference of stopping power were presented 0.7%, 1.0% and 1.3%, respectively. The data were analyzed through the kolmogorov-smirnov Goodness-of-Fit statistical analysis test. All the results from electromagnetic models showed a good agreement with the reference data, where all the corresponding p-values are higher than the confidence level $\alpha=0.05$ set.

양성자치료기 가속기 시설에서의 작업종사자의 방사선 피폭 연구

이상훈,신동호,윤명근,신정욱,라정은,곽정원,박성용,신경환,이두현,안성환,김대용,조관호,이세병,Lee, Sang-Hoon,Shin, Dong-Ho,Yoon, Myong-Geun,Shin, Jung-Wook,Rah, Jeong-Eun,Kwak, Jung-Won,Park, Sung-Yong,Shin, Kyung-Hwan,Lee, Doo-Hyun,Ahn, Sung 한국의학물리학회 2009 의학물리 Vol.20 No.1

국립암센터에 설치된 양성자 치료기는 양성자 가속기의 운영을 통해 많은 양의 이차방사선을 방출하게 되는데, 이는 양성자 빔이 가속 중에 주위의 물질과 반응을 하여 이차 입자를 발생하고 방사성 동위원소도 생성하기 때문이다. 생성된 방사성 동위원소에 의한 방사선량은 시간에 따라 감쇠되지만 양성자 치료기의 운영 및 유지보수를 위해 수시로 가속기 작업종사자들이 시설내부로 접근해야 하며 이로 인해 이차방사선에 의한 피폭 문제가 발생될 수 있다. 본 논문에서는 양성자 가속기(Cyclotron)를 포함한 양성자 치료기의 운영을 위해 필요한 작업종사자들의 작업환경을 평가하고, 적절한 수준의 방사선 방호대책을 수립하기 위해 양성자 치료기 운영 중 가장 높은 수준의 방사선이 발생되는 양성자 가속기(Cyclotron) 및 주변 지역에서의 가속기 가동에 따른 방사선 발생 정도를 측정하였고 그 지속시간을 분석하였다. 이를 위해 양성자 빔의 손실이 가장 큰 가속기 주변과 에너지 선택 시스템(Energy Selection System, ESS)지역의 탄소(graphite, $^{12}C$) 재질로 구성된 에너지 감쇠장치(degrader)에서의 방사선 변화를 추적하고, 가속기에서 생산된 230 MeV의 고정된 에너지 빔이 에너지 감쇠장치(degrader)를 거쳐 ESS를 통해 전송된 빔의 효율을 산출하고 빔의 전송 구간에서의 상대적인 방사화 정도를 분석하였다. 이러한 분석 자료를 토대로 작업종사자들의 작업간 피폭 수준을 계산하고 연간 피폭 정도를 측정하였다. 작업 중 가속기 시설내의 선량은 수십 ${\mu}Sv/h$로 다른 방사선 치료기에 비해 상대적으로 높은 수준이지만 작업시간을 고려한 연간 총 피폭 선량은 작업자에 따라 1~3 mSv/year 정도로, 연간 피폭 한계 선량보다 충분히 낮은 수준으로 운영이 가능하였다. Proton therapy facility, which is recently installed at National Cancer Center in Korea, generally produces a large amount of radiation near cyclotron due to the secondary particles and radioisotopes caused by collision between proton and nearby materials during the acceleration. Although the level of radiation by radioisotope decreases in length of time, radiation exposure problem still exists since workers are easily exposed by a low level of radiation for a long time due to their job assignment for maintenance or repair of the proton facility. In this paper, the working environment near cyclotron, where the highest radiation exposure is expected, was studied by measuring the degree of radiation and its duration for an appropriate level of protective action guide. To do this, we measured the radiation change in the graphite based energy degrader, the efficiency of transmitted beam and relative activation degree of the transmission beam line. The results showed that while the level of radiation exposure around cyclotron and beam line during the operation is much higher than the other radiation therapy facilities, the radiation exposure rate per year is under the limit recommended by the law showing 1~3 mSv/year.

비정질 셀레늄 기반 디지털 방사선 검출기의 성능 평가

박지군,강상식,조성호,신정욱,김소영,손대응,남상희,Park, Ji-Koon,Kang, Sang-Sik,Cho, Sung-Ho,Shin, Jung-Wook,Kim, So-Yeong,Son, Dae-Woong,Nam, Sang-Hee 대한의용생체공학회 2007 의공학회지 Vol.28 No.2

In this study, we have studied the fabrication and the performance evaluation of digital radiation detector of the based on selenium (a-Se) prototype which is widely researched about recently. The detector was fabricated using amorphous selenium in the specification of active area size $7{\times}8.5"$, pixel pitch $139{\mu}m$, and 12 bit ADC. In order for the performance evaluation of the fabricated detector, we used radiation quality RQA 5 that is suggested by the International Electrotechnical Commission (IEC), and evaluated modulation transfer function (MTF), noise power spectrum (NPS), and detective quantum efficiency (DQE). Concerning MTF measurement, we used slit camera (Nuclear Associates, Model : 07-624-2222), and evaluated in the slit method. Also so as to compare the performance evaluation on the detector fabricated in this study, we used Hologic Direct-Ray (DR-1000) and GE Revolution XQ/I system, and evaluated and compared in the same method MTF, NPS, and DQE which are image quality factors. And as a result, the MTF of each detector In Nyquist frequency were evaluated to be 58% (at 3.5 lp/mm) in the case of DR-1000 and 65% (at 2.5 lp/mm) in the case of XQ/I, and that for the detector fabricated in this study was evaluated to be 36% (at 3.51 lp/mm). Also in the case of DQE(0), the detector fabricated in this study, DR-1000 of Hologic company, and XQ/I system of GE company respectively were evaluated as 36%, 32%, and 50%.

형광체 기반 X선 광 변조기를 위한 비정질 셀레늄 필름 특성

강상식,박지군,조성호,차병열,신정욱,이건환,문치웅,남상희,Kang, Sang-Sik,Park, Ji-Koon,Cho, Sung-Ho,Cha, Byung-Youl,Shin, Jung-Wook,Lee, Kun-Hwan,Mun, Chi-Woong,Nam, Sang-Hee 대한의용생체공학회 2007 의공학회지 Vol.28 No.2

PXLM(Phosphor based x-ray light modulator) has a combined structure by phosphor, photoconductor, and liquid crystal and it can realize x-ray image of high resolution in clinical diagnosis area. In this study, we fabricated a photoconductor and investigated electrical and optical properties to confirm application possibility of radiator detector of PXLM structure. As photoconductor, amorphous selenium(a-Se), which is used most in DR(Digital radiography) of direct conversion method, was used and for formation of thin film, it was formed as $20{\mu}m-thick$ by using thermal vacuum evaporation system. For a produced a-Se film, through XRD(X-ray diffraction) and SEM(Scanning electron microscope), we investigated that amorphous structure was uniformly established and through optical measurement, for visible light of 40 $0\sim630nm$, it had absorption efficiency of 95 % and more. After fabricated a-Se film on the top of ITP substrate, hybrid structure was manufactured through forming $Gd_2O_3:Eu$ phosphor of $270{\mu}m-thick$ on the bottom of the substrate. As the result to confirm electrical property of the manufactured hybrid structure, in the case of appling $10V/{\mu}m$, leakage current of $2.5nA/cm^2$ and x-ray sensitivity of $7.31nC/cm^2/mR$ were investigated. Finally, we manufactured PXLM structure combined with hybrid structure and liquid crystal cell of TN(Twisted nematic) mode and then, investigated T-V(Transmission vs. voltage) curve of external light source for induced x-ray energy. PXLM structure showed a similar optical response with T-V curve that common TN mode liquid crystal cell showed according to electric field increase and in appling $50\sim100V$, it showed linear transmission efficiency of $12\sim18%$. This result suggested an application possibility of PXLM structure as radiation detector.

임플란트 지대주나사의 조임회전력이 연결부 안정성에 미치는 영향에 관한 3차원 유한요소해석 연구

엄태관,서승우,전계록,신정욱,정창모,Eom, Tae-Gwan,Suh, Seung-Woo,Jeon, Gyeo-Rok,Shin, Jung-Wook,Jeong, Chang-Mo 대한치과보철학회 2009 대한치과보철학회지 Vol.47 No.2

Statement of problem: Loosening or fracture of the abutment screw is one of the common problems related to the dental implant. Generally, in order to make the screw joint stable, the preload generated by tightening torque needs to be increased within the elastic limit of the screw. However, additional tensile forces can produce the plastic deformation of abutment screw when functional loads are superimposed on preload stresses, and they can elicit loosening or fracture of the abutment screw. Therefore, it is necessary to find the optimum tightening torque that maximizes a fatigue life and simultaneously offer a reasonable degree of protection against loosening. Purpose: The purpose of this study was to present the influence of tightening torque on the implant-abutment screw joint stability with the 3 dimensional finite element analysis. Material and methods: In this study, the finite element model of the implant system with external butt joint connection was designed and verified by comparison with additional theoretical and experimental results. Four different amount of tightening torques(10, 20, 30 and 40 Ncm) and the external loading(250 N, $30^{\circ}$) were applied to the model, and the equivalent stress distributions and the gap distances were calculated according to each tightening torque and the result was analyzed. Results: Within the limitation of this study, the following results were drawn; 1) There was the proportional relation between the tightening torque and the preload. 2) In case of applying only the tightening torque, the maximum stress was found at the screw neck. 3) The maximum stress was also shown at the screw neck under the external loading condition. However in case of applying 10 Ncm tightening torque, it was found at the undersurface of the screw head. 4) The joint opening was observed under the external loading in case of applying 10 Ncm and 20 Ncm of tightening torque. 5) When the tightening torque was applied at 40 Ncm, under the external loading the maximum stress exceeded the allowable stress value of the titanium alloy. Conclusion: Implant abutment screw must have a proper tightening torque that will be able to maintain joint stability of fixture and abutment. 연구목적: 임플란트 치료에서 흔히 발생하는 기계적인 문제점을 하나가 지대주나사의 풀림과 파절이다. 일반적으로 나사 연결의 안정성을 위해서는 지대주나사의 조임회전력에 의한 전하중을 나사의 탄성한계까지 증가시킬 필요가 있다. 그러나 저작운동에 의한 기능부하는 전하중이 가해진 지대주나사에 추가적인 인장력을 가하게 되어 나사의 풀림이나 파절의 가능성을 높인다. 이러한 풀림이나 파절을 방지하면서 동시에 최대의 결합 강도를 가지는 조임회전력을 찾는 연구가 필요하다. 본 연구는 지대주나사의 조임회전력이 임플란트-지대주 연결부 안정성에 미치는 영향을 3차원 유한요소 분석을 통하여 확인하고자했다. 연구 재료 및 방법: External butt joint를 가진 임플란트를 기반으로 3차원 유한요소 해석모형을 설계하였다. 조임회전력에 따른 지대주나사의 전하중을 이론치, 실험치 및 해석치를 비교하여 해석모형을 검증하였다. 검증한 해석모형에서 대해 조임회전력을 10 Ncm, 20 Ncm, 30 Ncm, 그리고 40 Ncm로 각각 적용하고 지대주에 30도 경사지게 250 N의 외부하중을 가하여 유산요소 해석을 실시하였다. 그 결과를 통해 지대주나사의 최대 등가응력을 계산하고 고정체와 지대주 연결부의 응력분포 및 이개거리(gap distance)를 산출하였다. 결과 및 결론: 본 연구조건 하에서 다음과 같은 결과를 얻었다. 1. 전하중은 조임회전력이 클수록 증가하였다. 2. 조임회전력 적용 후 최대 등가응력은 지대주나사 경부에서 발생하였으며, 나사산 체결부에서는 주로 경부쪽 네 개의 나사산에 응력이 집중되었다. 3. 외부하중을 가했을 때에도 조임회전력을 적용했을 때와 동일하게 최대 등가응력은 주로 지대주나사 경부에서 발생하였으나, 10 Ncm의 조임회전력을 적용한 경우에서는 지대주나사 두부밑면에서 발생하였다. 4. 외부하중을 가했을 때 10 Ncm와 20 Ncm의 조임회전력을 적용한 경우에서는 연결부 이개(joint opening) 현상이 관찰 되었다. 5. 조임회전력이 40 Ncm인 경우에는 경사하중에 의해 지대주나사의 경부에 발생하는 최대등가응력이 나사의 소재인 티타늄 합금의 허용응력을 초과하였다. 이상의 결과로 볼 때, 조임회전력은 고정체와 지대주 연결부의 안정성에 영향을 미치는 것이 확인되었다. 임플란트 지대주나사는 임상에서 발생하는 기능 하중을 고려하여 고정체와 지대주 연결의 안정성을 유지할 수 있는 적정 조임회전력의 크기가 제안되어야 한다.

전단응력에 의한 골육종 세포의 칼슘이온 시응답 특성 측정

박소희(So Hee Park),신정욱(Jung Wook Shin),정옥찬(Ok Chan Jeong) 대한전기학회 2008 대한전기학회 학술대회 논문집 Vol.2008 No.10

This paper presents the time responses of calcium (Ca²?) ion concentration of MG-63 cells induced by a constant shear mess in micro channel were observed in the real time. Most of cells have similar rising lime. There were some time delays because of the initial position of the cell in the micro channel along the pressure-driven fluid wolf The concentration of Ca²? exponentially decreased while time constant of each profile did not have any relation to the peak value of concentration.