http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
사공동식,김진목,차근식,Sakong, Dong-Sik,Kim, Jin-Mog,Cha, Jin-Mog 대한화학회 1997 대한화학회지 Vol.41 No.12
Tetradecyltrimethylammonium chloride(TDTMACl)을 첨가한 실리콘러버-지지체 전극막은 생체시료중 염화이온의 측정시 보다 향상된 전기화학적 특성을 나타내기 위하여 사용되었다. 이때 최적화된 전극막의 조성비는 95.4 wt% 실리콘러버, 4.6 wt% TDTMACl이며 이 전극막의 pH 감응성은 pH 6-10 영역에서 무시할 수 있었다. 이들 전극막들의 염화이온에 대해 감응기울기는 10-300 mM 영역에서 -3.75 mV/decade로 이론적인 Nernstian 감응기울기에는 못 미쳤으나 살리실레이트 이온 등 다른 음이온에 대한 선택성은 매우 우수하였다: KpotCl,NO3=1.3, KpotCl,I=2.0, KpotCl,Sal=0.8, KpotCl,SCN=2.0, KpotCl,ClO4=0.8. 또한 실리콘러버-지지체 전극막은 PVC-지지체 전국막에 비해 고체상 전극표면에 대한 접착력이 우수하므로 CWE형 고체상 전극에 도입되었을 때 향상된 전극수명을 나타내었다. 이들 고체상 전극들은 35일까지 염화이온에 대한 감응기울기나 살리실레이트 이온에 대한 감응성에 변화없이 우수하게 작동함을 알 수 있었다. Silicone rubber-matrix membranes doped with tetradecyltrimethylammonium chloride (TDTMACl) are used to enhance electrode performance for chloride measurements in physiological samples. The optimized membrane formulation incorporates 95.4 wt% silicone rubber and 4.6 wt% TDTMACl, and its pH response is negligible in the range of pH 6-10. The TDTMACl-doped silicone rubber membrane exhibits sub-Nernstian response to chloride from 10 to 300 mM (-37.5 mV/decade), but its selectivities for chloride over other anions are remarkably enhanced: KpotCl,NO3=1.3, KpotCl,I=2.0, KpotCl,Sal=0.8, KpotCl,SCN=2.0 and KpotCl,ClO4=0.8. Furthermore, since the silicone rubber-matrix membrane exhibits better adhesion to the solid surface than do PVC membranes, the lifetime of the coated-wire type membrane electrode is greatly improved. The response properties toward chloride and salicylate for solid-state sensor are not significantly changed after at least 35 days of use.
박종원,공동식,강승민 대한건축학회지회연합회 2014 대한건축학회연합논문집 Vol.16 No.4
장스팬화 경량화에 유리한 강재보와 압축력 및 횡강성에 유리한 PC 또는 합성 기둥으로 이루어진 복합구조는 각 재료의 장점을 최대한 활용한 합리적인 구조 형식이다 .그러나 이러한 복합 구조는 서로 다른 재료로 이루어진 부재 사이의 접합에 따른 어려움으로 인해 실용화가 활발히 이루어지지 못하고 있다. 또한 PC조립식 건축구조 시스템은 부재와 부재의 연결부에서 일체성이 떨어져 구조물의 강성 및 강도의 감소로 이어질 수 있는 단점이 있으며 시공단계에서 접합부의 일체성을 확보하지 못하는 경우 붕괴사고의 위험성이 있다. 따라서 대형 업무용 건축물에 합리적인 형식인 복합구조를 적용하면서 동시에 두 재료 사이의 접합을 쉽게 할 수 있는 새로운 접합형식의 개발이 요구 되어 많은 접합형식이 개발 되어 왔다. 그중에서도 강재보-PC기둥(또는 합성기둥) 접합부에 쐐기형 접합장치(Self Locking Connectors)를 적용한 접합방식은 기존 접합방식에 비해 내진성능이 우수하고 공기단축과 시공성의 향상으로 인한 경제적인 효과가 커질 것으로 기대가 된다. 하지만 이러한 장점을 확보하기 위해서는 체결케이스의 무게가 무겁지 않아야 한다. 본 연구에서는 쐐기형 보-기둥 접합장치의 시공성 및 경제성에 결정적으로 중요한 요소인 체결 케이스의 크기에 따른 강도 및 변형특성의 변화를 살펴보기 위해 체결케이스의 크기를 실험변수로 하여 단순인장 실험을 수행하였다. 실험결과 체결케이스가 작은 경우 연결되는 판재가 체결구멍에서 빠져나오면서 최대내력에 도달하는 파괴모드가 발생하며 체결케이스가 커지게 되면 판재가 항복한 후 파단하는 파괴모드가 발생하였다. 요구되는 하중에 따른 최적의 케이스 형상을 도출 하는 것을 목표로 하였다. 사무소 건축물에 일반적으로 사용되는 보 플랜지를 대상으로 한 120x17mm 판재를 지지하는데 필요한 체결케이스의 크기는 170x230x90이 적절한 것으로 나타났다. A new type of steel beam-to-concrete column connection using SL(self-locking) connectors was developed. The economy of this new type of connection depends greatly on the sizes of the SL connectors. The purpose of this study is to investigate the strengths of SL connectors used for connection between steel beam flange and concrete column. SL connectors of different sizes are tested under monotonic tension loading. Test results show that failure modes depend on the relative sizes of connectors and connected beam flange plates. If the size of a connector is reduced, ultimate strength is reached as the flange plate is pulled out of the connector. For better seismic performance of a beam-to-column connection, inelastic deformation has to occur in the beam flange rather than in connectors. Therefore sizes of connectors required for beam flange plates to reach their ultimate strengths before being pulled out are investigated in this study. This study shows that the size of SL connectors required for a flange plate of 90 x 20 mm is 200 x 240 x 90 mm.
( 고분자 / 액정 ) 복합막의 상분리구조와 전기광학 특성
박관선,노창호,사공동식,남기대,카지야마 ( K . S . Park,C . H . Noh,D . S . Sakong,K . D . Nam,T . Kajiyama ) 한국유화학회 1995 한국응용과학기술학회지 Vol.12 No.2
The phase separated structure and the electro-optical properties of the (polymer/liquid) crystal : LC) composite film strongly depended on the weight fraction of LC in it. The continuous LC phase was formed in a three-dimensional polymer network when the LC weight fraction was above 40wt%. The aggregation structure of the composite film could be controlled by controlling the solvent evaporation velocity during the film preparation process. The smaller LC domains or channels were formed in the case of the faster solvent evaporation velocity. The composite film exhibited reversible light scattering-light transmission switching upon electric field -OFF and -ON states, respectiverly. The light scattering properties of the composite film strongly depended on the spatial distortion of the nematic directors as well as the mismatch in refractive indices between matrix polymer and LC.
Thin Film Transister 구동 Polymer Dispersed Liquid Crystal 을 이용한 Over Head Projector 용 액정패널의 전기광학특성
박관선,진용완,사공동식 한국공업화학회 1998 응용화학 Vol.2 No.1
Thermally stable Polymer Dispersed Liquid Crystal(PDLC) having a low driving voltage(4.8V, high contrast and fast response time(30ms) has developed. The PDLC applied for the 10.4$quot; thin film transister- driving panel for Over Head Projector(OHP). The Brightness of the OHP greatly increased by using the Polymer Dispersed Liquid Crystal(PDLC) panel instead of a Twisted Nematic(TN) Liquid Crystal panel.
액정표시 소자용 고분자 / 액정 복합막의 전기광학 특성 개선
노창호,성준호,정재은,박관선,사공동식 ( C . H . Noh,J . H . Sung,J . E . Jung,K . S . Parl,D . S . Sakong ) 한국공업화학회 1995 공업화학 Vol.6 No.5
할로겐계 액정화합물과 광경화성 수지 화합물을 사용하여 액정/고분자 복합막 재료의 구동 전압, 응답 속도, 콘트라스트 비등의 구동 특성을 향상시켰다. 액정/고분자 복합막의 전기광학적 성질은 사용한 재료의 조성, 제조 온도 등의 제조 환경에 따라 상당한 영향을 받으며, 제조 조건의 최적화에 따라 전기 광학적 성질 및 신뢰성을 크게 향상시킬 수 있었다. 액정/고분자 복합막 재료의 전기 광학적 특성이 크게 개선됨에 따라 TFT 소자 등의 액티브 매트릭스 구동에 의한 고휘도, 대화면의 표시가 가능한 액정 프로젝터의 실용화에 보다 접근할 수 있게 되었다. Polymer Dispersed Liquid Crystal(PDLC) materials of low saturation voltage and high contrast ratio have been developed by using halogenated liquid crystals and photo-reactive acryl resin system. The other reliabilities such as hysteresis, temperature dependence and UV-stability of its electro-optical properties have been improved by optimising LCPC structure and synthetic conditions. Active-matrix addressed LCPC device having such a good electro-optical properties promises higher brightness and larger screen size for projection display.