http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
김우석,이재하,Kim, Woo Seok,Lee, Jaeha 한국전산구조공학회 2013 한국전산구조공학회논문집 Vol.26 No.6
본 연구에서는 풍진동에 대한 현수교의 거동을 예측하기 위하여 바닥판의 비틀림강성을 고려하여 Mckenna and Tuama 모델(2001)을 개선한 2D 간단해석 방법을 제안하였다. 기존의 모델은 풍속이 증가할수록, 진동수가 낮아질수록 비정상적인 값을 나타내고, 비틀림모드의 공진현상을 묘사할 수 없었다. 이에 본 연구에서는 비틀림강성을 고려하여 풍속에 따른, 진동수에 따른 비틀림진동을 분석하였다. 해석결과 진동 초기의 수직모드는 점차 비틀림모드로 전이되며 수직모드는 안정적으로 진동하는 것을 확인하였다. 또한 비틀림강성 효과를 고려하여 해석을 수행한 결과 수직모드는 시간이 경과함에 따라 안정화되는 모습을 보이나 비틀림 진폭은 일정시간(약 200초) 이후 나타나기 시작하여 비틀림각을 지속적으로 유지하였으며 맥놀이 주기는 풍속이 증가하면서 점차 감소하였다. 비틀림 강성에 따라 서로 다른 풍하중의 풍속과 진동수에 비틀림모드의 공진현상을 나타내므로 실제 설계에는 반드시 이러한 영향이 고려되어야 할 것이다. In this paper, 2D simple analyses were performed in order to predict the large torsional oscillations in a suspension bridge based on Makenna and Tuama model(2001). The existing model(Makenna and Tuama, 2001) has shown unrealistic results as the wind speed increases and frequency decreases. Furthermore, resonance could not be simulated by the existing model. Therefore, in this study, new model was proposed with a consideration of the torsional resistance. The vertical and rotational behaviors of the deck in the suspension bridge were analyzed. Analysis results showed that at first vertical oscillations were observed and it was gradually transformed to the rotation oscillations. With the consideration of the torsional resistance, it was shown that vertical behavior were stabilized as time passed. However, the rotational behavior was not stabilized and was kept until the end of analysis. Beat periods decreased while the wind speed increased. The resonance of the rotational mode was dependent to the rotational resistance. Obtained results could be applied for the design of the suspension bridge under the wind load.
비분산 적외선 분광법을 이용한 Co<sub>2</sub>농도 고속 분석기의 Sampling Module 특성에 관한 실험적 연구
김우석,손덕영,박영무,유재석,이종화,Kim, Woo-Seok,Shon, Deok-Young,Park, Young-Moo,Yoo, Jae-Suk,Lee, Jong-Hwa 대한기계학회 2003 大韓機械學會論文集B Vol.27 No.3
A fast response analyzer for measuring carbon dioxide concentration has been developed for transient characteristic and researches tested on internal combustion engine. The analyzer uses the well known NDIR(Non-Dispersive Infrared) method with miniaturized detection system, giving a time constant of approximately 30 microsecond, and sampling module consists of capillary tube. Since the transit time and the time constant of the sampling system depend on the sampling conditions, it is necessary to investigate the characteristics of sampling system before applied to exhaust gas measurement in engine. A unique method was designed to study the influence of the diameter of transfer sample line and operating conditions of the FRNDIR on transit time and time constant. A database of transit time and time constant was built up for different measured and simulated pressure conditions. The database can be used for correcting eventual $CO_2$ concentration measurement.
김우석,조순금,김민범,박지현,성미경,조혜린,유형천,Kim, Woo-Seok,Cho, Soon-Keum,Kim, Min-Beom,Park, Ji-Hyun,Sung, Mi-Kyoung,Cho, Hye-Rin,Ryu, Hyung-Cheon 대한한방안이비인후피부과학회 2015 한방안이비인후피부과학회지 Vol.28 No.4
Objectives : We performed a retrospective study to verify the effects of Chungan-tang and acupuncture in acne patients.Methods : This study included patients with facial acne who visited to six branch of clinics in 2014. They were evaluated by Korean Acne Grading System (KAGS) before and after treatment.Results : The average grade of KAGS was 4.02±1.120 at before treatment and 1.30±0.867 at after treatment. 64 patients were classified as three groups by treatment period and KAGS grade significantly decreased in all groups. Six skin symptoms such as heat, blush, dryness, itch, prick, pain also significantly improved.Conclusions : This results may provide that Korean medical treatments including Chungan-tang and acupuncture have effects on improving acne.
일체식 교대 교량의 대횡변위를 위한 교대와 H형 말뚝 연결부의 개발
김우석,이재하,박대효,Kim, Woo Seok,Lee, Jaeha,Park, Taehyo 한국전산구조공학회 2013 한국전산구조공학회논문집 Vol.26 No.4
본 논문에서는 일체식 교대 교량의 장대화 및 내진성능 향상을 위해 가장 중요한 역할을 하는 교대-H형 강말뚝 연결부의 성능을 향상시키기 위하여 기존의 연결부의 균열형상을 파악하고, 이를 기반으로 새로운 형태의 연결부를 제안하기 위하여 철근을 활용하여 강성을 증가시키는 방법과 강말뚝의 형상을 개선하여 연성을 개선시키는 방법을 모색하였다. 먼저, 기존 연결부의 성능을 향상시키기 위하여 연결부 주변에 PennDOT에 규정된 철근상세와 나선철근의 배치와 HSS 튜브를 사용하였으나, PennDOT의 철근 상세와 HSS 튜브는 연결부의 성능을 향상시키지 못 했으나, 나선철근은 균열을 효과적으로 차단시키는 것을 확인할 수 있었다. 하지만, 철근의 구속효과로 인해 강말뚝의 저항력이 변위에 선형적으로 비례하여 증가하므로 교량의 상부구조에 축력을 발생시키는 효과를 가져왔다. 따라서, 강말뚝의 형상을 개선하기 위하여 콘크리트 교대에 매입된 부분의 플랜지를 제거하는 방법과 콘크리트 외부에서 플랜지의 폭을 축소시키는 형태를 검토하였다. 두 가지 방안 모두 균열을 억제하는데 효과적인 방법이었으나, 플랜지를 제거하는 쪽의 연결부가 더욱 효과적이었다. Abutment-to-pile connection in an integral abutment bridge is vulnerable to lateral displacement induced by thermal movement of the superstructure. However, previous researches have merely focused on the connection. In order to improve the performance of the connection, new abutment-to-pile connection designs were proposed based on quasi-static nonlinear finite element model. The reinforcement detail specified in PennDOT DM4 and HSS tube were barely effective in controlling crack growing but spiral rebar effectively performed to delay crack growth as well as absorbing energy capacity. However, it was found that delaying cracking and strengthening the connection also caused the high lateral load in superstructures. Consequently, shape of HP pile were modified to introduce plastic hinge of the HP pile for reducing the lateral load in superstructures. Connections with modified HP pile significantly prevented crack propagations under the lateral displacement.
김우석(Woo-Seok Kim),서범(Beom Seo),임인섭(In-Seob Im) 한국산학기술학회 2017 한국산학기술학회논문지 Vol.18 No.4
본 연구는 다른 산업에 비해 정부의 부채비율 정책에 민감하다고 할 수 있는 우리나라 농업법인의 적정부채비율 추정을 위하여 이론적으로 도출 가능한 분석적 수리모형을 수립하고 객관적인 자료를 이용하여 적정부채비율을 추론하는데 목적이 있다. 분석모형은 독립변수를 부채비율로 하는 자기자본순영업이익률 계산식으로부터 출발하고 관련 모수는 매출액 영업이익률, 총자산회전율, 순금융비용율로 구성된다. 이 가운데 순금융비용율의 경우 부채비율과 1차 선형 관계를 고려한 방정식을 분석모형에 추가하는 등의 분석적 절차에 따라 적정부채비율 기준을 자기자본순영업이익률을 극대화하는 부채비율 수준으로 정의하고, 이들 식으로부터 자기자본순영업이익률은 부채비율을 독립변수로 하는 2차함수로 나타낸다. 이러한 분석방법 및 절차에 의해 우리나라 농업법인의 14년 자료를 토대로 적정부채비율을 도출한 결과 약 138% 정도의 부채비율이 농업법인 전체의 자기자본순영업이익률을 제고하는 것으로 나타났다. 이는 그동안의 농업법인 부채비율이 적정부채비율에 비해 비교적 높게 형성되어 있음을 알 수 있는 결과로써 기업이 부채비율을 관리하는 목적이 안전성 유지, 수익성 확대 등에 있고, 부채비율 관리에서 중요한 것이 수치에 대한 일률적 판단이 아닌 해당 업종의 특성을 고려한 대응이라고 했을 때 향후 농업법인에 대한 당국의 정책적 변화가 뒤따라야 할 것으로 보인다. This study employs an analytical mathematical model to estimate the optimal debt ratio of Korean agricultural corporations, more sensitive to the government debt ratio policy compared to other industries, and the estimation of the optimal debt ratio based on objective data. The analytical model utilizes the equation for ROE, with the debt ratio as an independent variable, and related parameters include ROS, TAT, and NFCL. Regarding the NFCL, the optimal debt ratio standard is defined as the debt ratio that maximizes the ROE by analytical procedures such as adding an equation concerning the debt ratio and a linearity relationship to the analytical model, and from these equations, a quadratic equation with the debt ratio as an independent variable describes the ROE. This methodemploys fourteen years of corporate data. Results show that 138% of debt ratio is the optimal debt ratio to increase the ROE of the corporations, which implies that the existing debt ratio of Korean agricultural corporations is higher than optimal. Consequently, it is required for authorities to change future debt ratio policies in view that the purpose of debt ratio management is to maintain safety and increase profitability.Management should emphasize characteristics of the specific industry rather than standardized judgements based on numerical indexes.