http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
전도성 접착제 물성에 따른 슁글드 어레이 태양전지 특성 평가
지홍섭(Hongsub Jee),최원용(Wongyong Choi),이재형(Jaehyeong Lee),정채환(Chaehwan Jeong) 한국태양광발전학회 2017 Current Photovoltaic Research Vol.5 No.3
The interconnecting shingled solar cells method shows extremely high ratio active area per total area and has the excellent potential for high power PV (photovoltaic). Compared to the conventional module, it can have much more active area due to busbar-free structure. The properties of ECA (electrically conductive adhesives) are significant to fabricate the shingled array PV since it should be used in terms of electric and structural connection. Various ECA were tried and characterized to optimize the soldiering conditions. The open circuit voltage of shingled array cells showed a three-fold increase and efficiency was also increased by 1.63%. The shingled array cells used in CE3103WLV showed the highest power and in CA3556HF the lowest curing temperature and very fast curing time.
무회전축 회전식 수상태양광 시스템 및 실증 데이터 분석
지홍섭(Hongsub Jee),김민우(Minwoo Kim),배재성(Jaesung Bae),정정호(Jeongho Jeong),이재형(Jaehyeong Lee) 한국태양광발전학회 2021 Current Photovoltaic Research Vol.9 No.4
In this study, the pivotless tracking type floating photovoltaic system was demonstrated successfully. The photovoltaic modules were installed on buoyant objects and the dynamic stability reinforcement mooring gear, tension control equipment and buoyant stabilizer were used to provide enough buoyance and stability and response to the external environment. After installation of the pivotless tracking type floating photovoltaic system, generated solar energy was collected and analyzed.
RF 마그네트론 스퍼터를 이용하여 제작한 MIZO 박막의 특성에 미치는 기판 온도의 영향
전기석(Kiseok Jeon),지홍섭(Hongsub Jee),임상우(Sangwoo Lim),정채환(Chaehwan Jeong) 한국태양광발전학회 2016 Current Photovoltaic Research Vol.4 No.4
Mg and In co-doped ZnO (MIZO) thin films with transparent conducting characteristics were successfully prepared on glass substrates by RF magnetron sputtering technique. The Influence of different substrate temperature (from RT to 400℃) on the structural, morphological, electrical, and optical properties of MIZO thin films were investigated. The MIZO thin film prepared at the substrate temperature of 350℃ showed the best electrical characteristics in terms of the carrier concentration (4.24×10<SUP>20</SUP>㎝<SUP>-3</SUP>), charge carrier mobility (5.01 ㎠V<SUP>-1</SUP>S<SUP>-1</SUP>), and a minimum resistivity (1.24×10<SUP>-4</SUP>Ω·㎝). The average transmission of MIZO thin films in the visible range was over 80% and the absorption edges of MIZO thin films were very sharp. The bandgap energy of MIZO thin films becomes wider from 3.44 eV to 3.6 eV as the substrate temperature increased from RT to 350°C. However, Band gap energy of MIZO thin film was narrow at substrate temperature of 400℃.
고출력 슁글드 태양광 모듈의 라미네이션 공정조건 최적화
정정호 ( Jeongho Jeong ),지홍섭 ( Hongsub Jee ),김정훈 ( Junghoon Kim ),최원용 ( Wonyong Choi ),정채환 ( Chaehwan Jeong ),이재형 ( Jaehyeong Lee ) 한국전기전자재료학회 2022 전기전자재료학회논문지 Vol.35 No.3
Global warming is accelerating due to the use of fossil fuels that have been used continuously for centuries. Now, humankind recognizes its seriousness, and is conducting research on searching for eco-friendly and sustainable energy. In the field of solar energy, which is a kind of eco-friendly and sustainable, many studies are being conducted to enhance the output performance of the module. In this study, the output improvement for the shingled module structure was studied. In order to improve the output performance of the module, the thickness of the encapsulant was increased, and the lamination process conditions have been improved accordingly. After that, the crosslinking rate was analyzed, and the suitability of the lamination process conditions was judged using this. In addition, a peeling test was conducted to analyze the correlation between the adhesion of the encapsulant and the output performance of the module. Finally, the optimization for the encapsulant material and the lamination process conditions for high-power shingled modules was established, and accordingly, the market share of high-power shingled modules in the solar module market can be expected to rise.
송진호(Jinho Song),지홍섭(Hongsub Jee),문대한(Daehan Moon),김도형(Do-Heyong Kim),양오봉(O-Bong Yang),정채환(Chaehwan Jeong) 한국태양광발전학회 2019 Current Photovoltaic Research Vol.7 No.2
The high density module (HDM) has advantages for its larger active area and smaller current density. This new way of making a photovoltaic (PV) module method has benefit for increasing module power with the same installed area. Because HDM consisted with serially connected PV strings, loss of strings during the fabrication process can increase the overall production cost.1-2 This study investigates the rework conditions of the shingled strings with electrically conductive adhesives (ECA). By heating the electrically connected area of a fabricated string, cured area become soft and a string can be detached for the rework process. After rework process, a refabricated string showed 5~10% increased output power compared to before rework process and reached to the 90~95% output power compare to the undamaged strings.
바이패스 다이오드 구성에 따른 슁글드 태양광 모듈의 특성 시뮬레이션
배재성(Jaesung Bae),지홍섭(Hongsub Jee),박용섭(Yong Seob Park),이재형(Jaehyeong Lee) 한국신재생에너지학회 2021 한국신재생에너지학회 학술대회논문집 Vol.2021 No.7
최근 건물 일체형 태양광 발전과 같은 도심형 신재생에너지 발전이 증가하게 되면서 제한된 면적에서 높은 출력을 생산할 수 있는 고밀도, 고효율 태양광 모듈에 대한 관심도 커지고 있다. 고밀도 태양광 모듈을 제작하기 위한 방법은 Multi-wire, Gapless, Shingled과 같이 여러가지 기술이 있다. 그 중 Shingled 기술의 경우 일반적인 태양전지를 분할/접합하여 제작하는 구조로 하나의 분할 셀 전면부에 다른 분할 셀이 오버랩 되어 접합되기 때문에 전면부의 버스바 영역이 수광영역으로 바뀌어 더 높은 출력을 생산할 수 있다. 또한, 일반적인 태양광 모듈에 비해 태양전지간의 절연을 위한 공간이 감소하게 되므로 고효율, 고밀도 태양광 모듈로 제작할 수 있다. 하지만 슁글드 태양광 모듈의 경우 분할된 셀들이 직렬로 접합되어 하나의 스트링으로 제작되기 때문에 일반적인 태양광 모듈에 비해 음영에 의한 출력 손실이 발생하기 쉬워진다. 그러므로 음영에 따른 슁글드 태양광 모듈의 출력 손실을 최소화하기 위해서는 슁글드 스트링의 회로구성 및 바이패스 다이오드의 최적화가 필요하다. 본 연구에서는 슁글드 태양광 모듈의 직렬 연결 배선 및 스트링 구조를 설계하였고 그에 따라 바이패스 다이오드 수를 가변하여 나타나는 특성을 시뮬레이션 하였다. 결과적으로 시뮬레이션을 통해 바이패스 다이오드의 수를 최적화하였고 그에 따른 슁글드 태양광 모듈의 음영 특성을 분석하였다.
정정호(Jeongho Jeong),김정훈(Junghoon Kim),지홍섭(Hongsub Jee),최원용(Wonyoung Choi),정채환(Chaehwan Jeong),이재형(Jaehyeong Lee) 한국신재생에너지학회 2021 한국신재생에너지학회 학술대회논문집 Vol.2021 No.7
최근 태양광 모듈 제작에 있어서 고출력을 내는 기술 중 하나인 슁글드 방식에 관한 연구가 활발히 진행되고 있다. 슁글드 모듈은 풀 셀을 사용하여 제작하는 기존 방식의 모듈보다 고출력을 낼 수 있는데 이는 동일 설치 면적에서 더 많은 수광 면적을 확보할 수 있기 때문이다. 그러나 기존의 모듈 제작에 사용하는 라미네이션 공정 조건은 슁글드 방식에는 적합하지 않은데, 슁글드 방식이 셀의 분할 및 접합 공정을 통해 제작되며 이로 인해 단차가 생기는 구조를 갖고 있기 때문이다. 최적화되지 않은 라미네이션 공정 조건을 통해 만들어진 모듈은 셀의 파손과 기포 발생 등을 일으키며 이는 모듈의 출력 저하 요소로 작용하게 된다. 본 연구에서는 이와 같은 문제점을 해결하기 위해 슁글드 모듈에 최적화된 라미네이션 공정에 대한 연구를 진행하였다. 셀의 파손 및 기포 발생을 해결하기 위해 EVA의 두께 및 라미네이션 공정의 최적화 연구를 하였으며, 제작된 모듈은 솔라시뮬레이터 및 EL 측정 장비를 통해 분석하였다.
Comparison of Solar Cells Interconnection with Metal Ribbons and Electrically Conductive Adhesives
Jaesung Bae(배재성),Juhwi Kim(김주휘),Jeongho Jeong(정정호),Jangwon Yoo(유장원),Chanyong Lee(이찬용),Hongsub Jee(지홍섭),Donggun Lim(임동건),Chaehwan Jeong(정채환),Jaehyeong Lee(이재형) 한국태양에너지학회 2021 한국태양에너지학회 학술대회논문집 Vol.2021 No.11