http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
수소 분위기 중 열처리법을 이용한 고자기이방성 L<sub>10</sub> FePt 박막 제작
공석현,김경환,Kong, Sok-Hyun,Kim, Kyung-Hwan 한국진공학회 2007 Applied Science and Convergence Technology Vol.16 No.5
Glass disk상에 대향 타겟식 스퍼터링(Facing Target Sputtering) 방식을 이용하여 $0.1\;{\AA}/s$의 낮은 증착속도로 증착시킬 경우 b.c.c. (100)면 우선배향성을 확인하였으며, 그 위에 Pt박막을 증착시킨 경우 hetero-epitaxial 성장에 의해 Pt박막이(111)의 조밀면이 아닌 (100)면이 우선배향 되었다. 이렇게 형성된 Fe (100)/Pt (100) 이층막(두께 각 3 nm)을 $600\;^{\circ}C$ 수소분위기에서 열처리함에 의해 막전체에 걸쳐서 f.c.t. (00n)면을 형성시키는 데 성공하고, 또한 Fe (100)면 상에 Pt 박막을 증착시키는 동안 열처리를 하고 증착 이후 수소분위기에서 열처리함에 의해 열처리 시간 및 온도를 크게 낮출 수 있음을 확인하였다. Fe thin films exhibited (100) preferential orientation when they were deposited at low deposition rate of $0.1{\AA}/s$ on glass substrates by using facing target sputtering system. The (100) oriented Fe layer induces (100) orientation of Pt layer deposited on it owing to hetero-epitaxial growth. After annealing at $600^{\circ}C$ in $H_2$ atmosphere, FePt films exhibited f.c.t. (001) texture in the whole film caused by inter-diffusion between atoms. We have also confirmed that the homogeneously inter-diffused compositional modulation in the film after the annealing process. Furthermore, annealing process in $Ar+H_2$ atmosphere at $400^{\circ}C$ during Pt deposition was effective for attaining Pt (100) texture. The annealing process during Pt deposition also induced in low annealing temperature and decreased annealing time for attaining the FePt f.c.t. (001) structure.
Mn-Zn-Fe-O 금속타깃을 이용한 수직자기기록디스크의 하지연자성층용 Mn-Zn ferrite 박막제작
공석현,김경환,Kong, Sok-Hyun,Kim, Kyung-Hwan 한국전기전자재료학회 2006 전기전자재료학회논문지 Vol.19 No.9
In order to attain high-rate deposition of Mn-Zn ferrite thin film for soft magnetic underlayer in perpendicular magnetic recording media, a reactive sputtering using powder-metal targets under the mixture gas of Ar and $O_{2}$ was performed. It was succeeded that Mn-Zn ferrite films with (111) crystal orientation were deposited on Pt(111) underlayer without any annealing process. The film revealed 3.4 kG of 4 ${\pi}Ms$, 70 Oe of coercivity. The deposition rate of the new method was 16 times as high as that of the conventional method using ferrite target.
태양전지용CuInSe<sub>2</sub>와 CuGaSe<sub>2</sub> 흡수층의 전자구조해석을 위한 표면 청정기술 개발
김경환,최형욱,공석현,Kim, Kyung-Hwan,Choi, Hyung-Wook,Kong, Sok-Hyun 한국전기전자재료학회 2005 전기전자재료학회논문지 Vol.18 No.2
Two kinds of physical treatments were examined for the analysis both of intrinsic surface and interior nature of CuInS $e_2$[CIS] and CuGaS $e_2$[CGS] films grown in separated systems. For the first method, a selenium protection layer which was immediately deposited after the growth of the CIS was investigated. The Se cap layer protects CISe surface from oxidation and contamination during the transport under ambient atmosphere. The Se cap was removed by thermal annealing at temperature above 15$0^{\circ}C$. After the decapping treatment at 2$25^{\circ}C$ for 60 min, ultraviolet photoemission and inverse photoemission measurements of the CIS film showed that its valence band maximum(VBM) and conduction band minimum (CBM) are located at 0.58 eV below and 0.52 eV above the Fermi level $E_{F}$, respectively. For the second treatment, an Ar ion beam etching was exploited. The etching with ion kinetic energy $E_{k}$ above 500 eV resulted in broadening of photoemission spectra of core signals and occasional development of metallic feature around $E_{F}$. These degradations were successfully suppressed by decreasing $E_{k}$ below 400 eV. CGS films etched with the beam of $E_{k}$ = 400 eV showed a band gap of 1.7 eV where $E_{F}$ was almost centered.st centered.
김경환(Kyung Hwan Kim),공석현(Sok-Hyun Kong) 한국표면공학회 2004 한국표면공학회지 Vol.37 No.4
Seedlayers with low surface energy which increases the density of nucleation sites in the initial growth region of the recording layer deposited on them was studied to reduce grain size in recording layer. The seedlayer with low surface energy was so effective to attain finer grain in magnetic upper-layers. The Ni-Fe-O intermediate layer with low surface energy was found to be effective in reduction of grain size as well as magnetic cluster size of Co-Cr-Ta-Pt recording layer. Furthermore, the reduction of grain size in Co-Cr- Ta-Pt recording layer on Ni-Fe-O intermediate layer with low surface energy led to decrease the noise level in the high recording density region.