http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
정재영,Jung, Jae-Young 한국건축시공학회 2003 한국건축시공학회지 Vol.3 No.4
과거의 대학교육이 교수 중심의 공급자 중심이었다고 한다면 미래의 교육은 수요자 중심의 교육, 즉 학생 중심의 교육이 되어야 한다는 논의가 무성하다. 또한 교육과정을 이수하고 졸업한 학생을 채용하는 기업이 바라는 교육의 내용이 무엇인지를 아는 것은 매우 중요하며 공학인증제도의 도입노력과 연관된다. 즉 회사가 채용한 대학 졸업생의 실력을 통하여 대학의 교육성과를 최종수요자인 회사가 평가하여 그 결과를 대학의 교육과정에 피드백하는 것이 공-학인증제도의 취지이다. 그러므로 회사가 원하는 졸업생의 능력을 갖추도록 대학교육의 커리큘럼을 구성하는 것이 바람직하고 그렇지 못한 대학은 채용에 있어서 불이익을 받을 것이다. (중략)
Kroll법에 의한 타이타늄 스폰지 생성기구에 관한 연구
정재영,손호상,Jung, Jae-Young,Sohn, Ho-Sang 한국자원리싸이클링학회 2017 資源 리싸이클링 Vol.26 No.5
In this study, we investigated the effect of $TiCl_4$ injection time on the Kroll reaction at a given weight ratio of $TiCl_4$ and Mg. The reduction reaction was investigated by measuring the temperature change according to $TiCl_4$ injection time and observing the cross section and appearance of the Ti sponge after the reaction. The temperature increment due to Kroll reaction heat generation was found to be linearly proportional to the $TiCl_4$ feed rate. In the graph of $TiCl_4$ injection time and reduction tank temperature, initial temperature peaks were observed irrespective of the injection conditions. This is interpreted to mean a temporary interruption of reaction due to $MgCl_2$ formation after the initial Kroll reaction. In addition, when the cross section of the sponge was observed, a large amount of spherical Mg particles was observed in $MgCl_2$. We can infer that this is the process of continuously feeding the unreacted Mg surface, so that a continuous Kroll reaction takes place. The sponge appearance showed that the coalescence or growth of the Kroll reacted Ti particles can be controlled by the cooling rate. 본 연구에서는 $TiCl_4$ 투입시간의 효과가 $TiCl_4$ and Mg의 주어진 중량비율에서 Kroll반응에 미치는 효과를 조사하였다. 그리고 환원반응은 $TiCl_4$ 투입시간에 따라 온도변화를 측정하고, 반응 후 Ti 스폰지 단면과 외관을 관찰함으로써 조사되었다. Kroll 반응열 생성에 의한 온도 증분은 $TiCl_4$ 투입속도에 직선적으로 비례하는 것으로 파악되었다. $TiCl_4$ 투입시간과 환원조 온도 그래프를 보면, 초기 온도 피크가 주입조건에 무관하게 모두 관찰되었다. 이는 초기 Kroll 반응후 $MgCl_2$ 형성으로 인한 일시적인 반응 중단을 의미하는 것으로 해석된다. 또한 스폰지 단면을 관찰해보면, 구형 Mg 입자상이 $MgCl_2$ 내부에 다량으로 관찰되었다. 우리는 이것이 지속적인 Kroll 반응이 일어나도록 미반응 Mg 표면을 계속적으로 공급하는 과정이라 추론할 수 있다. 주사전자현미경으로 스폰지 외형을 관찰한 결과는 Kroll 반응된 Ti 입자들의 합체나 성장이 냉각속도에 의해 제어될 수 있음을 보여주었다.
Plasma Arc Remelting에서 활성 금속 Scrap 재활용에 미치는 공정인자의 연구
정재영,손호상,Jung, Jae-Young,Sohn, Ho-Sang 한국자원리싸이클링학회 2017 資源 리싸이클링 Vol.26 No.6
본 연구에서는 anode로 Kroll 공정 처리된 Ti 스폰지를 사용하여 아크 전류, 아크 전압, 플라즈마 가스 종류에 따른 플라즈마 아크 재용해 거동을 조사하였다. 진공펌프의 토출 압력 범위($200{\sim}300kgf/cm^2$)에서는 토출 압력 증가에 따라 주어진 아크 길이에서 아크 전압이 크게 달라지지 않았다. 이것은 작업하는 동안 진공챔버내 압력이 거의 변화하지 않고, 주어진 분위기 압력을 잘 유지함을 의미한다. 여러가지 아크 전류 조건(700~900A)에서, 아크 전류 증가에 따라 아크 전압이 약간 증가하였고, anode 재료변화에 대한 효과도 이전 연구결과와 비교하였다. 분위기 가스가 Ar에서 He으로 변경되는 경우에는 정상상태의 출력이 2배 정도 향상되는 효과가 관찰되었다. 플라즈마 아크 장치의 출력 증가는 Ti 스폰지의 재용해 속도 증가와 함께 잉곳 표면도 양호해졌다. New 스크랩인 타이타늄과 old 스크랩인 지르코늄 합금을 플라즈마 아크 재용해한 결과, 매우 양호한 표면을 갖는 잉곳을 제조할 수 있었다. In this study, plasma arc remelting behaviors according to arc current, arc voltage, and types of plasma gas were investigated using Kroll processed Ti sponges as anode. In the discharge pressure range of vacuum pump ($200{\sim}300kgf/cm^2$), the arc voltage did not vary greatly with the increase of discharge pressure at a given arc length. This means that the pressure in the vacuum chamber during operation hardly changes and the atmospheric pressure maintains. Under various conditions of arc currents (700~900A), the arc voltage slightly increased with arc current. The effects of anode materials and operational variables on the arc length-arc voltage relationship were compared with the results in previous studies. When the atmospheric gas changed from argon to helium, double effect of improvement on the output of the steady state was observed. The increase of output in the plasma arc device was accompanied by an increase in the melting rate of the Ti sponge and the quality of the ingot surface was also improved. The plasma arc remelting of the new scrap titanium and the old scrap zirconium alloy could result in the fabrication of an ingot with high surface quality.
표 서식 문서의 구조 분석을 위한 선분 에지 기반의 유형별 꼭짓점 검출
정재영(Jae-young Jung) 한국디지털콘텐츠학회 2014 한국디지털콘텐츠학회논문지 Vol.15 No.2
It is very important to classify a lot of table-form documents into the same type of classes or to extract information filled in the template automatically. For these, it is necessary to accurately analyze table-form structure. This paper proposes an algorithm to extract corner points based on line edge segments and to classify the type of junction from table-form images. The algorithm preprocesses image through binarization, skew correction, deletion of isolated small area of black color because that they are probably generated by noises.. And then, it processes detections of edge block, line edges from a edge block, corner points. The extracted corner points are classified as 9 types of junction based on the combination of horizontal/vertical line edge segments in a block. The proposed method is applied to the several unconstraint document images such as tax form, transaction receipt, ordinary document containing tables, etc. The experimental results show that the performance of point detection is over 99%. Considering that almost corner points make a correspondence pair in the table, the information of type of corner and width of line may be useful to analyse the structure of table-form document.
430 스테인리스강 스트립재를 이용한 일렉트로슬래그 클래딩 용착금속의 화학성분 및 미세조직 변화
정재영(Jae-Young Jung),하태권(Tae-Kwon Ha) 대한용접·접합학회 2017 대한용접·접합학회지 Vol.35 No.5
In this study, the weld metals were obtained by electroslag strip cladding process using 430 stainless steel strip according to welding process parameters such as welding current, welding voltage, welding speed and polarity. We measured carefully the micro-Vickers hardness, microstructure, and chemical composition in the crosssectional area of the electroslag strip cladding overaly using the AISI 430 stainless steel strip. The hardness of the cross section between the weld metal and the base metal was measured to be higher than those of the base metal and the weld metal around the boundary, which was related to the microstructure and chemical composition of the boundary. Particularly, the intermediate region of the boundary was observed, and the chemical composition of the constituent elements continuously changed in this part. The microstructural changes of the weld metal and the base metal were shown that the coarse pearlite structure, the fine perlite structure, the bainite structure, the martensite structure and the dual structure of the d-ferrite / martensite were observed from the base metal to the weld metal. The change of the constituent elements of the deposited metal after welding were analyzed by comparing with measured and calculated values. The variation in the deposited metal composition was mainly due to the interaction with the flux.