http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
용융탄산염 연료전지용 in-situ 소결된 Ni-Al 합금 연료극 개발
천현아,윤성필,한종희,남석우,임태훈,Chun, H.A.,Yoon, S.P.,Han, J.,Nam, S.W.,Lim, T.H. 한국전기화학회 2006 한국전기화학회지 Vol.9 No.3
기존의 용융탄산염 연료전지용 연료극인 Ni-Cr전극은 제조과정이 복잡하며, 운전조건에서 전극의 소결과 creep현상으로 인하여 전극의 기공률과 두께가 감소하는 문제점이 있어 상용화에 걸림돌이 되고 있다. 이에 본 연구에서는 Ni-Cr계 전극보다 creep저항성이 우수하다고 알려져 있는 Ni-Al계 합금을 사용하였다. 또한 공정의 단순화로 비용을 절감시키기 위해, 소성과정을 제외하고 tape casting과 건조과정을 거친 green sheet를 단위전지에 장착하여 전처리 과정 중에 소결시키는 in-situ 소결법에 대해 연구하였다. 그러나 기존의 전처리 방법을 이용한 단위전지 평가에서 Ni-Al 합금의 상분리 현상으로 인해 기대하였던 creep저항성 향상을 확인하지 못했고, 운전중 Ni-Al합금 연료극에 단위전지의 구성요소인 matrix 기공크기보다 작은 기공(${\leq}0.4{\mu}m$)이 다량 생성되어 전해질 재분배를 일으켜 성능이 하락하는 문제점이 나타났다. 따라서 이러한 문제점을 해결하고자 전처리 조건을 변화시키며 실험을 수행하였다. 그 결과, 비활성 기체인 질소를 일정한 구간에 사용함으로써 기존 전처리에서 발생하였던 Ni-Al 합금의 상분리 현상을 억제할 수 있었으며 이로 인해 creep저항성 또한 향상시킬 수 있었다. 그러나 운전 중 생성되는 matrix기공크기보다 작은 기공(${\leq}0.4{\mu}m$) 형성비율은 억제할 수 없었다. 위의 전처리 조건을 가지고 단위전지 운전실험을 하였고, 전해질 함침비율을 조절함에 따라 성능을 향상시킬 수 있었으며 2000시간 동안 일정하게 유지함을 확인하였다. 이로부터 기존의 소성전극과 비교하여 많은 장점을 가지고 있는 in-situ 소결법의 가능성을 확인할 수 있었다. For commercialization of molten carbonate fuel cell (MCFC), it has some problems to be overcome such as decrease of porosity and thickness of the anode under the operating condition (at $650^{\circ}C$ and working pressure of more than 2 $kg_f/cm^2$). Recently, Ni-Al alloy anode has been proposed to replace the conventional Ni-Cr anode as an alternative material to resist a creep and inhibit the sintering. The objective of this research is to sinter the green sheet of Ni-Al alloy anode during single cell pre-treatment process, which has several advantages like cost down and simplification of manufacturing process. However, the Ni-Al alloy anode prepared with a conventional pre-treatment process showed the phase separation of Ni-Al alloy and formation of micropore(${\leqq}0.4{\mu}m$), resulting in low creep resistance and high electrolyte re-distribution. In order to prevent the Ni-Al alloy anode from phase-separating, nitrogen gas was used in the process of pre-treatment. Introducing the nitrogen, the phase separation from Ni-Al alloy into nickel and alumina was minimized and increased creep resistance. However, there was some micropore formation on the surface of Ni-Al alloy anode during the cell operation due to creation of lithium aluminate. Addition of more amount of electrolyte into a cell, especially at cathode, made the cell performance stable for 2,000 hrs. Consequently, it was possible to make the Ni-Al alloy anode with good creep resistance by the modified in-situ sintering technique.
슬러리 코팅법에 의한 스테인레스 스틸 표면에서의 알루미늄 확산막 제조 및 용융탄산염 내에서의 내식 특성 연구
남석우,황응림,아나톨리 마가뉵,홍명자,임태훈,오인환,홍성안,Nam S. W.,Hwang E. R.,Magtanyuk A. P.,Hong M. Z.,Lim T. H.,Oh I. -H.,Hong S. -A. 한국전기화학회 2000 한국전기화학회지 Vol.3 No.3
용융탄산염 연료전지의 분리판 재료로 사용되는 스테인레스 스틸은 고온 용융탄산염 분위기에서 부식이 심각하여 일반적으로 표면에 알루미늄 확산막을 코팅함으로써 내식성을 향상시켜 사용하고 있다. 본 연구에서는 기존 방법에 비해 보다 경제적인 슬러리 페인팅 및 열처리에 의한 알루미늄 확산막 형성 방법을 고안하여, 스테인레스 스틸 시편 표면에 알루미늄 확산막을 코팅하고, 산화 분위기의 용융탄산염에서 부식 실험을 수행하였다. $650\~800^{\circ}C$에서 제작된 알루미늄 확산막의 두께는 $25\~80{\mu}m$였으며, 열처리 온도가 높고 열처리 시간이 증가할 수록 알루미늄 확산막의 두께가 증가하였다. 부식 실험 결과 스테인레스 스틸 316L의 용융탄산염에 대한 내식성은 알루미늄 확산막을 표면에 형성시킴으로써 크게 향상되었음을 확인하였다. 또한 분극 실험 결과 슬러리 페인팅 및 열처리 방법에 의하여 알루미늄 확산막이 형성된 시편은 기존의 IVD 및 열처리 방법에 의해 알루미늄 확산막이 제작된 시편과 유사하게 안정한 부동태 피막을 형성함으로써 스테인레스 스틸 316L의 부식을 효과적으로 억제시킴을 알 수 있었다. A stainless steel separator for a molten carbonate fuel cell is usually coated with aluminum diffusive layer to protect its surface against corrosion by the molten carbonate at high temperatures. In this study, a relatively simple method was devised to form the aluminum diffusive layer on a stainless steel substrate. Slurry coating of aluminum on the substrate followed by heat treatment under reducing atmosphere at $650\~800^{\circ}C$ produced the aluminum diffusive layer of $25\~80{\mu}m$ thickness. The thickness of aluminum diffusive layer increased with increasing the temperature or duration of the heat-treatment. The corrosion resistance against molten carbonate under oxidizing atmosphere was significantly improved by aluminum diffusive layer formed by the sluny painting and heat treatment method. Moreover, the sample prepared in this study showed corrosion behavior similar to the sample with aluminum diffusive layer prepared by ion vapor deposition and heat treatment.