http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
김준곤,우형주,최한우,김기동,홍완,Kim Joonkon,Woo H. J.,Choi H. W.,Kim G. D.,Hong W. The Korean Vacuum Society 2005 Applied Science and Convergence Technology Vol.14 No.2
지난 10년 동안 유전체 내부에 형성된 나노미터 크기의 규소알갱이는 발광센터로서 주목 받아왔다 나노미터 크기인 결정질 규소의 엑시토닉 전자-홀의 쌍들이 발광결합에 기여한다고 여겨진다. 그러나 규소결정에 존재하는 여러가지 결함들은 비발광 천이의 경로가 되어 나노규소결접립의 발광천이와 경쟁하여 발광효율을 저하시키는 요인이 된다. 이러한 결정 결함들은 고온 열처리과정에서 대부분 소멸되나 $1000^{\circ}C$ 이상의 공정 에서도 나노규소와 유전체의 계면에 존재하는 결함들은 나노규소결정립의 발광을 억제하게 된다. 일반적으로 수소로서 규소결정립의 계면을 마감처리하게 되면 규소결정립의 발광효율이 획기적으로 향상되나 불행하게도 매질 내 수소의 높은 이동성으로 말미암아 후속 열처 리 과정에서 수소마감효과는 쉽게 손실된다. 따라서 본 연구에서는 온도가역적인 수소 대신 인을 이온주입 방법으로 첨가하여 수소와 같은 계면 마감효과를 얻으며 또한 후속 고온공정 에 대한 내구력을 증대시켰다. 모재인 산화규소 기판에 400keV, $1\times10^{17}\; Si/cm^2$와 그 주위에 균일한 함량을 도핑하기 위하여 다중에너지의 인을 주입하였다. 규소와 인을 이온주입 후 Ar 분위기에서 $1100^{\circ}C$ , 두 시간의 후열처리를 통하여 규소결정립을 형성하였으며 향상된 내열효과를 시험하기 위하여 Ar 분위기에서 $1000^{\circ}C$까지 열처리하였다. 인으로 마감된 나노미터 크기인 규소 결정립의 향상된 광-발광(PL)효과와 감쇄시간, 그리고 발광파장의 변화에 대하여 논의하였다. Nanometric crystalline silicon (no-Si) embedded in dielectric medium has been paid attention as an efficient light emitting center for more than a decade. In nc-Si, excitonic electron-hole pairs are considered to attribute to radiative recombination. However the surface defects surrounding no-Si is one of non-radiative decay paths competing with the radiative band edge transition, ultimately which makes the emission efficiency of no-Si very poor. In order to passivate those defects - dangling bonds in the $Si:SiO_2$ interface, hydrogen is usually utilized. The luminescence yield from no-Si is dramatically enhanced by defect termination. However due to relatively high mobility of hydrogen in a matrix, hydrogen-terminated no-Si may no longer sustain the enhancement effect on subsequent thermal processes. Therefore instead of easily reversible hydrogen, phosphorus was introduced by ion implantation, expecting to have the same enhancement effect and to be more resistive against succeeding thermal treatments. Samples were Prepared by 400 keV Si implantation with doses of $1\times10^{17}\;Si/cm^2$ and by multi-energy Phosphorus implantation to make relatively uniform phosphorus concentration in the region where implanted Si ions are distributed. Crystalline silicon was precipitated by annealing at $1,100^{\circ}C$ for 2 hours in Ar environment and subsequent annealing were performed for an hour in Ar at a few temperature stages up to $1,000^{\circ}C$ to show improved thermal resistance. Experimental data such as enhancement effect of PL yield, decay time, peak shift for the phosphorus implanted nc-Si are shown, and the possible mechanisms are discussed as well.
수중음향센서의 소음차단을 위한 다층구조 설계 최적화에 대한 연구
김강천,김성희,김준곤,길현권,홍석윤,송지훈,권현웅,서영수,전재진,Kim, G.C.,Kim, S.H.,Kim, J.K.,Kil, H.G.,Hong, S.Y.,Song, J.H.,Gwon, H.W.,Seo, Y.S.,Jeon, J.J. 한국음향학회 2013 韓國音響學會誌 Vol.32 No.4
본 논문은 수중함에 부착되는 소나(sonar)에서 소음차단을 위하여 일반적으로 사용되는 다층구조의 설계 최적화를 수행하였다. 설계 목표로서는 자함 자체 기계가진 진동으로 인하여 음향센서에 유기되는 음압이 낮도록, 그리고 외부 표적 함정으로부터 방사되어오는 음에 기인한 소나의 수신 음압이 운용주파수 대역에서 높고 고른 음압을 갖도록 하는 두 가지 상반된 설계 목표를 고려하였다. 설계 변수로서는 다층구조 각층의 재료 물성치 선택에 따른 이산변수와 각 층의 두께 변수인 연속변수를 함께 고려하여, 각 변수의 최적화 과정에 따른 영향도를 분석 하였고, 최적화 방법으로서는 진화알고리즘을 적용하였다. 또한 최적화 과정으로서는 두 가지 목표를 각각 고려하는 경우와 동시에 두 가지 복합적인 목표를 고려하는 경우에 대한 설계 최적화를 수행하여, 각 경우에 대한 설계 목표치의 최대화 정도를 분석하였다. In this paper, the optimization has been performed to design a multi-layer structure that is used as a structure for noise reduction of acoustic sonar sensors in underwater vehicles. Two design goals are considered to reduce self-noise from own machineries and to enhance acoustic signals detected from outside. Both distinct and continuous design parameters have been used such as selection of material properties of each layer and thickness of each layer, respectively. The sensitivity of design parameters has been analyzed and the evolutionary algorithm has been implemented for design optimization. For design optimization process, each of the design goals and the two combined design goals have been considered to analyze the achievement of those design goals.