혼수상태의 외상환자에서 초음파를 이용한 흉부 및 복부손상의 진단

임경수,이강현,이진웅,이부수,황성오,유수영,강성준 대한응급의학회 1995 대한응급의학회지 Vol.6 No.1

The need for rapid diagnosis and treatment of life-threatening thoracic and intra-abdominal injury result in controversy over the appropriate triage of unconscious blunt trauma patients. To aid in early decisions for these patients, a prospective analysis of 98 patients with glasgow coma scale(GCS) scores≤8 was undertaken. Although intra-thoracic and intra-abdominal injuries were frequently identified based on systolic blood ressure, the use of clinical signs alone resulted in more missed injuries than did using the emergency ultrasonography. In normotensive patients(n=34), intra-thoracic injuries was identified in one patient(2.9%), and intra-abdominal injuries were in 7 patients(20.6%). In shock(systolic blood pressure<90mmHg) Pa-tients(n=64), thoracic injuries and intra-abdominal injuries were diagnosed in 8(12.5%) and 27 patients(42.3%), thoracic and abdominal combined injuries were identified in 11 patients(17.2%). The sensitivity, specificity, and accuracy of emergency ultrasonography were 96.3%, 91.7%, 94.9%. This study suggests that all unconscious trauma patients undergo immediate emergency ultrasonography to prevent missing life-threatening injuries.

마이크로 어셈블리용 6자유도 정렬기의 기구학적 분석 및 디자인

유용환,이문구,이수훈,홍민성,송준엽,이창우 한국공작기계학회 2008 한국공작기계학회 추계학술대회논문집 Vol.2008 No.-

This work will develop a 6-DOF precision aligner with small size and high resolution for assembling the micro parts for a mobile electronics. Here, Tiny PicomotorTM actuator that is small and reliable will be applied to this aligner system. The principle of this actuator is PZT that turns a precision thread and then the screw moves linearly. Arrangement of actuators will be a symmetrical based on kinematic design. This paper presents combining two modules of mechanism for the 6-DOF precision aligner. The first is a stage which can control XYθz motion, and the second can control Z motion, in other words, Z tilt motion. According to its specifications, it is expected to satisfy requirement of precision.

토사 절토사면 안정성 영향인자의 민감도 분석

유남재,박병수,전상현,조한기 강원대학교 산업기술연구소 2006 産業技術硏究 Vol.26 No.B

A sensitivity analysis about effects of influencing factors on the stability of Soil cut slope was performed. Slope stability analyses were carried out under dry, rainy and seismic conditions. Dominant factors controlling the slope stability were chosen such as cohesion and internal friction angle, unit weight of soil, water table and seismic horizontal coefficient used for the slope stability during eurthquake. Parametric stability analysis with those factors was performed for sensitivity analysis. As results of analyzing the sensitivity of factors under dry and rainy conditions, effects of cohesion, internal friction angle and unit weight of soil on the stability of slope are more critical in the dry condition than in the rainy condition. Cohesion and internal friction angle are more dominant factors influencing the slope stability irrespective of dry or rainy conditions than unit weight of soil and the horizontal seismic coefficient. The unit weight and the horizontal seismic coefficient affects crucially the stability according to conditions of slope formation and dry or rainy seasons. For the effect of horizontal seismic coefficient on stability of slope, safety factor of slope is not affected significantly by dry or rainy conditions, However, increase of the horizontal seismic coefficient under the rainy condition does reduce the safety factor significantly rather than the dry condition. Therefore, it is needed that the location of the water table is assigned appropriately to satisfy the required safety factor of stability in the case of checking slope stability for the rainy and seismic conditions.

Modified 9Cr-1Mo 강의 항온변태처리에 따른 미세조직 및 경도변화

유정훈,주성욱,허성강,신기삼,이수,정연길 국립7개대학공동논문집간행위원회 2003 공업기술연구 Vol.3 No.-

Evolution of microstructure and its relation with hardness in the modified 9%Cr-1%Mo steel which was isothermally heat-treated has been investigated in various heat-treatment temperatures and time of duration. For microstructural and crystallographic analyses, optical microscope, scanning and transmission electron microscopes, energy dispersive spectrometer, and X-ray diffractometer were used. Vickers microhardness tester were used for the measurement of hardness. Precipitates of the complex M23C6, M(C,N) formed at grain boundaries and interiors of grains had led to the secondary hardening. Normalized specimen and all of the isothermally heat-treated ones showed no evidence of retained austenite.

프로판 기체의 점화 과정에서 수소 기체 첨가 효과에 관한 연구

유상조,신권수 崇實大學校 生産技術硏究所 2001 論文集 Vol.31 No.-

The addition effect of hydrogen on the ignition of propane was studied behind reflected shock waves over the temperature range of 1349-1599 K and the pressure range of 0.90-1.16 bar. The ignition delay times were measured by monitoring pressure propiles and the OH emissions at 1.0 cm from the end wall. It was found that the ignition dalay time of propane was decreased considerably by the small amount of hydrogen. The computer simulation of the effect of hydrogen additive in the ignition of propane was carried out using various mechanisms reported previously.

Gurney 플랲의 공기역학적 성능

유능수,정성웅 江原大學校 産業技術硏究所 1998 産業技術硏究 Vol.18 No.-

A numerical investigation was performed to determine the effect of a Gurney flap on a NACA 23012 airfoil. A Navier-Stokes code. RAMPANT, was used to calculate the flow field about airfoil. The fully turbulent results were obtained using the standard k-ε two-equation turbulence model. To provide a check case for our computational method. computations were performed for NACA 4412 airfoil which compared with Wedcock's experimental data. Gurney flap sizes of 0.5,1.0, 1.5, and 2% of the airfoil chord were studied. The numerical solutions showed the Gurney flap increased both lift and drag. These results suggested that the Gurney flap served to increased the effective camber of the airfoil. But Gurney flap provided a significant increase in lift-to-drag ratio relatively at low angle of attack and for high lift coefficient. Also, it turned out that 0.5% chord size of flap was best one among them.

원심모형실험에 의한 모래다짐말뚝의 지지력 산정식 연구

유남재,홍영길,전상현,김경수 강원대학교 산업기술연구소 2007 産業技術硏究 Vol.27 No.A

Centrifuge model tests were performed to find appropriate equations proposed previously of estimating the bearing capacity of the composite clayey soil reinforced with sand compaction pile. Model tests were carried out with changing the replacement ratio of SCP (20%, 40%, 70%), contents of fine materials (5%, 10%, 15%) and ratio of treated width to loading width (1B, 2B, 3B). Test results about bearing capacity of the composite ground were obtained by performing the surcharge load tests with measurements of applied loads and vertical displacement. Bearing capacities against bulging and shear failures were estimated by the existing equations. As results of comparing the estimated bearing capacity with experimental values the bearing capacities estimated by Greenwood's equation (1970) for bulging failure mode were similar to the test results.

모래다짐말뚝의 원심모델링

유남재,정길수,김상진,채승호 江原大學校 産業技術硏究所 2001 産業技術硏究 Vol.21 No.B

This paper is results of extensive centrifuge model experiments about design factors influencing the bearing capacity and the settlement behaviors of SCP (Sand Compaction Pile). Centrifuge model tests were carried out changing design factors for SCP method such as replacement area ratio (as= 20, 40, 70%), improvement ratio to footing width (W/B = 1, 2, 3), and amount of fines in sand pile (#200 = 5, 10, 15). Therefore, the effects of these design factors on the bearing capacity and the settlement behavior of SCP were investigated and changes of stress concentratio rato due to such an design factors were also investigated. Centrifuge model testing technique for preparing and installing centrifuge model of sand compaction pile, using freezing them, was also developed. As results of centrifuge model tests, more fines in sand compaction pile increases the bearing capacity of SCP. Optimum improvement ratio to footing width was found to be 2. Values of stress concentration ratio was in the ranges of 1.5 - 3.5. The depth of bulging in sand piles was found in the range of 2.0 - 2.5 times of pile diameter.

후두부 발작성 간질파와 동반된 양성 소아기 간질의 임상적 연구

유영수,이상도,김지언,임정근,박영춘 대한신경과학회 1996 대한신경과학회지 Vol.14 No.4

확률론적 해석법에 의한 연직배수 영향인자 민감도 분석

유남재,전상현,정길수,김동건 강원대학교 산업기술연구소 2006 産業技術硏究 Vol.26 No.B

A probabilistic analysis model, one of reliability analysis methods introducing the concept of probabilistic variables, was developed to investigate the uncertainty of dominant factors influencing the degree of consolidation in the radial consolidation theories. Based on the developed probabilistic analysis model, sensitivity study of those factors was performed to find their trends of affecting the degree of consolidation in the vertical drain method. Various radial consolidation theories, Proposed by Barron(1948), Hansbo(1979), Yoshikuni(1979) and 0noue(1988), were used for this parametric study with the influencing factors such as size of smear zone, reduction ratio of permeability in the smear zone, discharge capacity, permeability for horizontal flow and coefficient of consolidation for horizontal flow. As results of this sensitivity study, for the given consolidation theory, contribution of each factor to the degree of consolidation was figure out and compared to each other. For the given value of each factor, the sensitivity to the degree of consolidation in the various theories was evaluated and their applicability and limitations were assessed.