Cu(In,Ga)Se₂ 나노입자을 이용한 광흡수층 치밀화에 따른 Se 분위기의 열처리 효과

윤경훈(Yoon, Kyung-Hoon),김기현(Kim, Ki-Hyun),안세진(Ahn, Se-Jin),안병태(Ahn, Byung-Tae) 한국신재생에너지학회 2006 한국신재생에너지학회 학술대회논문집 Vol.2006 No.06

나노입자를 이용하여 치밀한 Cu(In,Ga)Se₂ 태양전지용 광흡수층을 제조하기 위해 먼저, 콜로이달 방법으로 합성된 20nm이하의 CIGS 나노입자를 저가의 스프레이 법을 이용하여 CIGS 막을 제조하였다. 제조된 CIGS막을 two-zone RTP (rapid temperature Process) 방법으로 Se 분위기 안에서 열처리를 행하였다. 입자의 치밀화를 위해 기판의 온도, Se 증발온도와 수송가스의 유량을 조절하여 CIGS 입자성장을 행하였다. 그러나, Se의 증발온도가 높을수록 CIGS와 MO 박막 사이에서 MoSe₂ 층이 형성되었다. 형성된 MoSe₂층의 부피 팽창으로 인해 하부의 유리기판과 Mo층 사이에서 peeling off 현상이 발생했다. 이러한 Peeling off현상을 억제하면서 CIGS 나노입자 성장을 하기 위해, Se 공급을 빨리 할 수 있도록 Se의 증기압을 높였으며, 최적조건에서 급속 열처리 공정을 통해 CIGS 나노입자 성장과 치밀화를 위한 소결거동을 관찰하였다.

Physical & Chemical Deposition Techniques for Cu(In,Ga)Se2-Based Thin Film Solar Cells (초)

( Kyung Hoon Yoon ),( Jae Ho Yun ),( Se Jin Ahn ),( Byung Tae Ahn ) 대한금속재료학회 ( 구 대한금속학회 ) 2007 대한금속재료학회 학술대회 개요집 Vol.2007 No.1

Chalcogenization-Derived Band Gap Grading in Solution-Processed CuIn_<i>x</i>Ga_1–<i>x</i>(Se,S)₂ Thin-Film Solar Cells

Park, Se Jin,Jeon, Hyo Sang,Cho, Jin Woo,Hwang, Yun Jeong,Park, Kyung Su,Shim, Hyeong Seop,Song, Jae Kyu,Cho, Yunae,Kim, Dong-Wook,Kim, Jihyun,Min, Byoung Koun American Chemical Society 2015 ACS APPLIED MATERIALS & INTERFACES Vol.7 No.49

<P>Significant enhancement of solution-processed CuInxGa1-x(Se,S)(2) (CIGSSe) thin-film solar cell performance was achieved by inducing a band gap gradient in the film thickness, which was triggered by the chalcogenization process. Specifically, after the preparation of an amorphous mixed oxide film of Cu, In, and Ga by a simple paste coating method chalcogenization under Se vapor, along with the flow of dilute H2S gas, resulted in the formation of CIGSSe films with graded composition distribution: S-rich top, In- and Se-rich middle, and Ga- and S-rich bottom. This uneven compositional distribution was confirmed to lead to a band gap gradient in the film, which may also be responsible for enhancement in the open circuit voltage and reduction in photocurrent loss, thus increasing the overall efficiency. The highest power conversion efficiency of 11.7% was achieved with J(sc) of 28.3 mA/cm(2), V-oc of 601 mV, and FF of 68.6%.</P>

비진공 나노입자 코팅법을 이용한 CIGS 박막 태양전지 제조

안세진(Ahn, Se-Jin),김기현(Kim, Ki-Hyun),윤경훈(Yoon, Kyung-Hoon) 한국신재생에너지학회 2006 한국신재생에너지학회 학술대회논문집 Vol.2006 No.06

A non-vacuum process for Cu(In,Ga)Se₂ (CIGS) thin film solar cells from nanoparticle precursors was described in this work CIGS nanoparticle precursors was prepared by a low temperature colloidal route by reacting the starting materials (CuI,;InI₃,;GaI₃;and;Na₂Se) in organic solvents, by which fine CIGS nanoparticles of about 20nm in diameter were obtained. The nanoparticle precursors were mixed with organic binder material for the rheology of the mixture to be adjusted for the doctor blade method. After depositing the mixture of CIGS with binder on Mo/glass substrate, the samples were preheated on the hot plate in air to evaporate remaining solvents ud to burn the organic binder material. Subsequently, the resultant (porous) CIGS/Mo/glass simple was selenized in a two-zone Rapid Thermal Process (RTP) furnace in order to get a solar ceil applicable dense CIGS absorber layer. Complete solar cell structure was obtained by depositing. The other layers including CdS buffer layer, ZnO window layer and Al electrodes by conventional methods. The resultant solar cell showed a conversion efficiency of 0.5%.

Ga 함유량에 따른 Cu(In_1-xGa_x)Se₂ 박막 태양전지에 관한 연구

송진섭(Song, Jin-Seob),윤재호(Yoon, Jae-Ho),안세진(Ahn, Se-Jin),윤경훈(Yoon, Kyung-Hoon) 한국신재생에너지학회 2007 한국신재생에너지학회 학술대회논문집 Vol.2007 No.06

Cu(In_1-xGa_x)Se₂(CIGS)는 매우 큰 광흡수계수를 가지고 있으므로 박막형 태양전지의 광흡수층 재료로서 많은 연구가 진행되고 있다. 박막이 태양전지의 광흡수층으로 이용되기 위해서는 큰 결정크기와 평탄한 표면, 적당한 전기적 특성을 가져야 한다. 이러한 특성들은 CIGS 박막의 조성에 큰 영향을 받고 있는 것으로 보고되고 있다. 본 연구에서는 동시증발법을 이용하여 Cu/(In+Ga) 비를 0.9로 고정한 후 Ga 조성(Ga/(In+Ga)의 비 : 0.32, 0.49, 0.69, 0.8, 1)을 변화시켜 Wide band gap CIGS 박막태양전지를 만들었다. 기판은 soda line glass를 사용하였고 뒷면 전극으로는 Mo를 스퍼터링법으로 증착하였다. 또한 버퍼층으로는 기존에 쓰이고 있는 CdS를 CBD(Chemical Bath Deposition)법으로 층착시켰으며, 윈도우층으로는 i-ZnO/n-ZnO를 스파터링 법으로 층착하였다. 그리고 앞면전극으로는 Al을 E-beam 으로 증착하였다. 분석은 XRD, SEM, QE로 분석하였다. 위 실험에서 얻은 결과로는 Ga/(In+Ga)비가 증가할수록 Cu(In,Ga)Se2 박막은 회절 peak들이 큰 회절각으로 이동하였고, 이것은 Ga 원자와 In 원자의 원자반경의 차이에서 기인된 것으로 사료된다. 또한 Ga 조성이 증가할수록 단파장 쪽으로 이동하는 것을 볼 수 있으며, Voc가 증가하다가 에너지 밴드캡이 1.62 eV 이상에서는 Voc가 감소하는 것을 볼 수 있는데 이것은 Ga 조성이 증가할수록 에너지 밴드캡이 커지면서 defect level 이 존재하기 때문인 것으로 사료된다. Ga/(In+Ga)비가 1일 때의 변환효율은 8.5 %이고, Voc : 0.74 (V), Jsc : 17.2 (mA/cm²), F.F : 66.6(%) 이다.

Association between Socioeconomic Status and Altered Appearance Distress, Body Image, and Quality of Life Among Breast Cancer Patients

Chang, Oliver,Choi, Eun-Kyung,Kim, Im-Ryung,Nam, Seok-Jin,Lee, Jeong Eon,Lee, Se Kyung,Im, Young-Hyuck,Park, Yeon Hee,Cho, Juhee Asian Pacific Journal of Cancer Prevention 2014 Asian Pacific journal of cancer prevention Vol.15 No.20

Background: Breast cancer patients experience a variety of altered appearance - such as loss or disfigurement of breasts, discolored skin, and hair loss - which result in psychological distress that affect their quality of life. This study aims to evaluate the impact of socioeconomic status on the altered appearance distress, body image, and quality of life among Korean breast cancer patients. Materials and Methods: A cross-sectional survey was conducted at advocacy events held at 16 different hospitals in Korea. Subjects were eligible to participate if they were 18 years of age or older, had a histologically confirmed diagnosis of breast cancer, had no evidence of recurrence or metastasis, and had no psychological problems at the time of the survey. Employment status, marital status, education, and income were assessed for patient socioeconomic status. Altered appearance distress was measured using the NCI's cancer treatment side effects scale; body image and quality of life were measured by the EORTC QLC-C30 and BR23. Means and standard deviations of each outcome were compared by socioeconomic status and multivariate linear regression models for evaluating the association between socioeconomic status and altered appearance distress, body image, and quality of life. Results: A total of 126 breast cancer patients participated in the study; the mean age of participants was 47.7 (SD=8.4). Of the total, 83.2% were married, 85.6% received more than high school education, 35.2% were employed, and 41% had more than $3000 in monthly household income. About 46% had mastectomy, and over 30% were receiving either chemotherapy or radiation therapy at the time of the survey. With fully adjusted models, the employed patients had significantly higher altered appearance distress (1.80 vs 1.48; p<0.05) and poorer body image (36.63 vs 51.69; p<0.05) compared to the patients who were unemployed. Higher education (10.58, standard error (SE)=7.63) and family income (12.88, SE=5.08) was positively associated with better body image after adjusting for age, disease stage at diagnosis, current treatment status, and breast surgery type. Similarly, patients who were married and who had higher education had better quality of life were statistically significant in the multivariate models. Conclusions: Socioeconomic status is significantly associated with altered appearance distress, body image, and quality of life in Korean women with breast cancer. Patients who suffer from altered appearance distress or lower body image are much more likely to experience psychosocial, physical, and functional problems than women who do not, therefore health care providers should be aware of the changes and distresses that these breast cancer patients go through and provide specific information and psychosocial support to socioeconomically more vulnerable patients.

橋梁上板形 積層復合板의 振動數에 대한 添加質量의 影響

김경진,심도식,이세진,박제선 江原大學校 産業技術硏究所 1996 産業技術硏究 Vol.16 No.-

A method of calculting the natural frequency corresponding to the first mode of vibration of beams and tower structures with irregular cross-sections and with arbitrary boundary conditions was developed and reported by D. H.Kim in 1974. In order to obtain the natural frquency by the presented method, the first step to take is to obtain the deflection influence surfaces. In design and analysis of a ny structure, the first step to be taken is to obtain this deflection influence surfaces. Any method can be used for this purpose . Then using this surfaces, deflections, slopes, moments, shears, and natural frequencies can be obtained by differentiating either the continuous function or discrete function defined at certain points. The merit of the presented method is that the natural frequency can be obtained by the deflection influence surfaces obtaining which is the first step in structural analysis.

대구치에서 회전식 NiTi file의 수명과 파절양상

김진우,안병두,박세희,신혜진,조경모 大韓齒科保存學會 2005 Restorative Dentistry & Endodontics Vol.30 No.3

Intracanal separation of the rotary files is a serious concern in modern endodontic practice. The objective of this study was to compare the life span and fracture patterns of three NiTi rotary files in molar teeth. Mesiobuccal roots of upper molar (n = 150) and mesial roots of lower molar (n = 150) were divided into three groups and each group was prepared with Profile, ProTaper, and K3 respectively. Every file was used until separation and/or deterioration of the cutting blade was happened, and then the number of canals to separation and/or unwinding were recorded. Radiographs and Scanning electon microscope (SEM) photographs were taken to evaluate the patterns of separation. The results were as follows: 1. There were no significant differences in numbers of canals to separation and/or unwinding among the groups. 2. Comparing between flaring files, K3 showed significant lower numbers of canals to separation and/or unwinding (p < 0.05), and there was no significant difference between shaping files 3. Separations of instruments were occurred at the midpoint of curvatures within the canals 4. In SEM observations, ductile fractures were seen in most of cases, characterized by shallow dimples. Additional researches is needed to provide a new guideline that informs the appropriate number of times to use NiTi files. 회전식 NiTi file은쉽게 파절되는 단점이 있으나 이에 대한 연구는 아직 부족하다. 본 연구에서는 회전식 NiTi file을 이용해 실제 치아에서 근관을 형성하고, 이 때 발생하는 파절 및 변형을 연구, 분석하였다. 상악 대구치의 근심협측 치근 (n = 150)과 하악 대구치의 근심치근 (n = 150)을 실험대상으로 하여 Profile, ProTaper 및 K3로 각각 근관형성 하였다. 각 file은 파절되거나 변형이 생길 때까지 계속하여 사용한 다음 그 사용횟수를 기록하였다. 파절의 양상을 관찰하기 위해 방사선 및 주사현미경 사진을 촬영하였다. 1 세 군간의 유의할만한 사용횟수의 차이는 없었다. 2. Flaring file 간의 비교에서는 K3의 사용횟수가 통계적으로 유의성 있게 적었으며 (p < 0.05), shaping file 간에는 유의할만한 차이가 없었다. 3, 회전식 NiTi file의 파절은 근관의 최대 만곡부에서 발생하였다. 4. 주사전자현미경으로 파절면을 관찰한 결과 연성파괴의 전형적인 양상인 얕은 딤플이 관찰되었다. 일반적으로 회전식 NiTi file의 평균 사용횟수는 제조회사의 사용지침보다는 길었으며, NiTi file의 수명에 대한 새로운 사용지침을 만들기 위한 부가적인 연구가 있어야 되리라 사료된다.

레진 시멘트를 이용한 레진 파이버 강화 레진포스트의 치근 상아질에 대한 미세인장결합강도

김진우,유미경,이세준,이광원 大韓齒科保存學會 2003 Restorative Dentistry & Endodontics Vol.28 No.1

Object The purpose of this study were to evaluate the microtensile bond strength of resin fiber reinforced post to radicular dentin using resin cement according to various dentin surface treatment and to observe the interface between post and root dentin under SEM. Material and Method A total 16 extracted human single rooted teeth were used. A lingual access was made using a #245 carbide bur in a high-speed handpiece with copious air water spray. The post space was mechanically enlarged using H-file(up to #60) and Gates Glidden bures(#3). This was followed by refining of the canal space using the calbrating drill set provided in ER Dentinpost(GEBR, BRASSELER GmbH&Co. KG). The 16 teeth were randomly distrubuted into 4 group of 4 teeth. Group 1 teeth had their post space prepared using 10% phosphoric acid as root canal surface treatment agent during 20s. The canal was then rinsed with saline and dried with paper point. Group 2 teeth had their post space prepared using 3% NaOCI as root canal surface treatment agent during 30min. The canal was then rinsed with saline and dried with paper point. Group 3 teeth had their post space prepared using 17% EDTA as root canal surface treatment agent during 1min. The canal was then rinsed with saline and dried with paper point. Group 4 teeth had their post space prepared using 17% EDTA as root canal surface treatment agent during 1 min. After rinsing with saline, the canal was rinced 10ml of 3% NaOCI for 30min. After drying with paper point, the post(ER Dentinpost, GEBR, BRASSELER GmbH&Co. KG) was placed in the treated canals using resin cement. Once the canal was filled with resin cement(Super bond C&B sunmedical co. Ltd.), a lentulo was inserted to the depth of the canal to ensure proper coating of the root canal wall. After 24 hours, acrylic resin blocks(10·15·50mm) were made. The resin block was serially sectioned vertically into stick of 1·1mm. Twenty sticks were prepared from each group. After that, tensile bond strengths for each stick was measured with Microtensile Tester. Failure pattern of the specimen at the interface between post and dentin were observed under SEM. Results 1. Tensile bond strengths(meen±SD) were expressed with ascending order as follows ; group 4, 12.52±6.60 ; group 1, 7.63±5.83 ; group 2, 4.13±2.31 ; group 3, 3.31±1.44. 2. Tensile bond strengths of Group 4 treated with 17% EDTA +3%NaOCI were significant higher than those of group 1, 2 and 3 (p<0.05). 3. Tensile bond strengths of Group 1 treated with 10% phosphoric acid were significant higher than those of group 2 (p<0.05). Tensile bond strengths of Group 4 treated with 17% EDTA +3% NaOCI was significant higher than those of other groups.

Terfenadine과 Ketoconazole 복용 후 발생된 Torsades de pointes 심실 빈맥증의 치험 1례

김세경,이기중,유승진,박일영,박승현,임근우,이원재,강동헌 대한응급의학회 1995 대한응급의학회지 Vol.6 No.1

Torsades de pointes is a form of polymorphic ventricular tachycardia that is associated with prolongation of the QT interval, characterized by QRS complexes of progressively changing amplitude and contour that seem to revolve around the isoelectric line. The most common cause of Torsades de pointes induced by antiarrhythmic agents, occupying in certain drugs or toxin, electrolyte disturbance, congenital QT prolongation syndrome. Cardiotoxicity terfenadine, in overdose a widely used, nonsedating antihistamine, has been reported. Case after administration of terfenadine and ketoconazole causing syncope and torsades de pointes have been reported in recommended dose. We report a case of QT prolongation with torsades de pointes after therapeutic administration of terfenadine, a long acting histamine H1 receptor antagonist, together with ketoconazole, an antifungal preparation. The patient is a 43-year-old female, who experienced palpitation, dizziness and syncopal episoders after coadministration of terfenadine and ketoconazole, for a fungal infection of the skin. The ECG showing typical episodes of torsades de pointes with QT prolongation. Magnesium sulfate was given, torsades de pointes did not recur. The patient was discharged with improved condition.