Hall 소자를 이용한 승강기용 로프의 평가

이종오,윤운하,손영호,김정우,이종규 한국비파괴검사학회 2003 학술대회 논문집 Vol.- No.1

홀 소자를 이용한 누설자속 측정으로 승강기용 와이어 로프의 결함 검출에 대한 연구를 수행하였다. 소선파단, 마모, 내부 소선파단 형태의 인공결함을 제작하여 시험편에 영구자석으로 자장을 걸어 결함에서 누설되는 누설자속을 홀 센서를 사용하여 검출하였다. 로프의 소선은 0.5, 0.8mm 두 종류로 시험결과 단선모델 시험에서 0.4mm, 내부의 소선 파단의 경우 1mm 정도 깊이를 가진 인공결함까지 검출이 가능하여 1개의 소선 파단도 검출할 수 있는 것으로 보인다. 마모모델에서 결함의 폭이 작은 경우 검출이 불가능하였으나, 폭이 4mm이상인 경우 자극이 결함을 통과할 때 자속의 변화에 의해 깊이가 0.2mm 정도의 작은 결함도 구별이 가능하였다. 따라서 Hall 센서에 의한 누설자속 측정이 wire rope의 결함 검출에 좋은 도구가 된다고 본다. Defect detection of wire rope for an elevator was investigated through the measurement of magnetic flux leakage. The types of defect usually found in wire rope categorized such as inner and outer wire breakage and wear. The specimens that has artificial defects were magnetized via permanent magnet, and measurement of magnetic flux leakage on the defects was performed with Hall sensor. In wire broken model, a defect smaller than 0.4mm and 1mm in depth on outer and inner wire rope, respectively, could be detected well. In wear model, smaller defect could not be detected clearly, however, appearance of changing of total magnetic flux during magnetic pole of the sensor passing through a defect 0.2mm in depth at 4mm or above width could make possible to detect it. From the results, the measurement via Hall sensor might be useful tool for defect detection of wire rope.

항파상풍 톡소이드 주사후 항파상풍 항체 역가

이한식,하영록,구홍두,장석준,심호식,김승환,이정운 대한응급의학회 1996 대한응급의학회지 Vol.7 No.2

Objective : Tetanus decreased in prevalence since the systemic vaccination began in 1940s. Despite of the improvement in treatment like critical care with ventilatior or antibiotics, the mortality rate resides around 45%. Currently the tetanus prevention protocol recommends immunization in infancy and boosters every tenth years. Thereafter the immunization with toxoid only or toxoid plus immunoglobulin injections is recommended according to the type of injury. In most of ED in Korea, only tetanus immunoglobulin is given without any basis. Previously we proved the effect that passive immunization with the immunoglubulin 250 IU last long for only a month. At this time we measured the effect of the active immunization with toxoid and its effect was compared to the effect of the tetanus immunoglobulin to find out the logical tetanus prevention after an injury. Method: 20 healthy adult volunteers were injected with tetanus toxoid and their anti-tetanus antibody titers measured before the injection, 1 week and 4 weeks after the inection. No volunteers have taken any medication for chronic illness(e.g. hepatits, tuberculosis) or had an tetanus immunization or booster in the last 6 months. Antibody titers were measured by IMMUNOZYM??-TETANUS and t-test was performed on the results, Results: 1. Total 20 volunteers(12 males and 8 females) were participated. 2. Subjects` ages were 21 to 44 years old and there were no relevance to the antibody titer. 3. The antibody titers of before the anti-tetanus toxoid injection and 1 week, 4 weeks after the injection revealed significant difference and the antibody titers of the first and the forth week after the injection also showed a significant difference. Conclusion: Currently in Korea, the tetenus immunoglobulin 250 IU given alone as tetanus prevention was injected, but it did not elevate the anti-tetanus antibody titer for 4 weeks where as tetanus toxoid injected intramuscularly did significantly. Therefore, tetanus toxoid should be given on the dirty injuries with additional tetanus immunoglobulin injection to accomplish the correct method of tetanus, tetanus toxoid prevention.

유한요소법을 이용한 치근단절제술후 근첨의 응력분포에 관한 연구

이세준,최호영,민병순,박상진,최기운 大韓齒科保存學會 1998 Restorative Dentistry & Endodontics Vol.23 No.1

The purpose of this study is to evaluate the distribution of stress in the root end resected teeth. The finite element method was used to compare stresses along the root and retrograde filling material in seven two-dimensional models of mandibular 2nd premolar. Each model was endodontic treatment and gold crown restoration. Each model divided with amagam corerestoration or gold casting post restoration. Thus each model divided with shape of root end resection, depth of retropreparation and exposure length of root in the bony cavity. The seven models were classified as in the table 1 below. ◁표참조▷ A load of 500N was applied 45°diagonally on the lingual slope of the buccal cusp. These models were analyzed with two dimensional finite element methods. The results of this study were as follows : 1. The maximum tensile stress along the inner canal wall was shown on the model 7. 2. When the model 1 was compared with the model 5, the maximum tensile stress along the inner canal wall showed the model 1. 3. Less equivalent stress was shown on the model 6 and more equivalent stress was shown on the model 4. 4. More shear stress was shown on the retrograde filling material of the model 7. 5. The models with increased length of exposed root in the bony cavity demonstrated a gradual increase to the tensile stress in X direction which occurred approximately a boundary between the bone and exposed root in the bony cavity. 6. The model which had a case of matching the apex of post and a boundary between the bone and exposed root in the bony cavity demonstrated more increase tensile stress in X direction than other models.

졸 - 겔법에 의한 다공성 알루미나 미분체 제조에 관한 연구 : 2 . 물과 알콕시드의 비가 알루미나 미분체의 결정화 공정에 미치는 영향 2 . The Effect of [ H2O ] / [ Al - alkoxide ]on The Crystallization Mechanism of As - Prepared Particles

이성원,박형상,윤호성,황운연,구기갑,유승준,김용렬,이정운 한국화학공학회 2001 Korean Chemical Engineering Research(HWAHAK KONGHA Vol.39 No.2

알루미늄 알콕시드의 반응속도를 제어하기 위한 혼합용매와 입자제조 과정에서의 응집을 방지하기 위한 분산제로 HPC를 첨가하는 방법에 의하여 구형의 다공성 알루미나 미분체를 제조하였으며, XRD, FT-IR 및 TG-DTA 분석을 통하여 공정변수로 선정한 물과 알루미늄 알콕시드의 비가 제조된 미분체의 결정화 공정에 미치는 영향에 대하여 고찰하였다. 축중합 반응에 첨가된 물과 Al-알콕시드의 비는 제조된 미분체 및 하소 공정을 거친 미분체의 결정구조에 영향을 미침을 알 수 있었다. [H₂O]/[ASB]의 비가 증가할수록 제조된 미분체는 비정질의 Al(OH)₃로부터 점진적으로 AlO(OH)의 화학조성을 갖는 의사-보헤마이트로 결정성이 바뀌었다. 그리고 건조 공정을 거친 미분체의 결정성이 좋을수록 δ와 θ-Al₂O₃는 저온에서 생성되었으나, α-Al₂O₃는 고온에서 생성되었다. 이와 같은 결과는 Al^(3+)이온의 결정 내에서의 배위체 변화와 관계됨을 알 수 있었다. 그리고 [H₂O]/[ASB]=2의 조건에서 제조된 입자는 다른 시료와 달리 600℃에서 η-Al₂O₃로 1,100℃에서 α-Al₂O₃2로 상전이 되었다. Spherical porous alumina particles were prepared by mixed solvent to control the reaction rate of Al-alkoxide and the particle shape with hydroxy-propyl cellulose(HPC). HPC was used as a dispersant to prevent aggregation during the formation of particles. The effect of [H₂O]/[ASB] ratio on the crystallization reactions of as-prepared particles was studied by XRD, FT-IR, and TG-DTA analysis. The mole ratio of water and Al-alkoxide added in the condensation reaction had an important effect on the crystal structure of as-prepared particles and the calcined particles. As the [H₂O]/[ASB] ratio increase, the crystal structure of as-prepared particles was continuously varied from amorphous Al(OH)₃ to pseudo-boehmite with chemical composition of AIO(OH). The samples which have higher crystallinite after drying process were transformed into the δ- and θ-Al₂O₃ at lower calcination temperature, but these sample were transformed into α-Al₂O₃ at higher calcination temperature. This result was thought to be the transformation of the coordination number of Al^(3+) ion in the crystal structure. The particles prepared by [H₂O]/[ASB]=2 condition crystallized to α-Al₂O₃at 600℃ and converted to η-Al₂O₃at 1,100℃ without intermediate phases.

캔디다균이 분비하는 단백질 분해효소의 순수 분리와 특성 및 교차 항원성

이경호,신운섭,박주영,김수기,박윤선,고춘명 연세대학교 원주의과대학 1995 원주의대논문집 Vol.8 No.1

척수 경막외 혈관 기형에 의한 재발성 척수병증

오동호,김희태,박운규,이영주,김승현,김주한,김명호,박문향 대한신경과학회 1998 대한신경과학회지 Vol.16 No.5

간질환자의 간질 관련 외상

오동호,박운규,이영주,김희태,김승현,김주한,김명호,신동진 대한신경과학회 1998 대한신경과학회지 Vol.16 No.4

성인 여성의 자궁경부암 및 유방암 조기검진 수검행위에 영향을 미치는 요인

노윤녕,김영복,박용문,이원철,맹광호 韓國保健敎育.健康增進學會 2000 보건교육건강증진학회지 Vol.17 No.1

This study was aimed at preparing basic dada required for establishment of a cancer screening program by examining the status of cancer screenings performed by women in a city and the factors that had an influence on cervical and breast cancers screening behavior of women. In order to find out the status of cervical and breast cancers screening and the factors having an influence on cervical and breast cancers screening behavior, 1,113 women were selected as study area and subjects by a random cluster sampling method, and the subjects were answered by questionnaires. The major results were as follows. 1.In the cases of the breast and the cervical cancers, 16.7% and 55.7% of the subjects turned out to have had one or more screenings respectively in their life-time. Also the rate of screening group of cervical and breast cancers was 16.7%, the rate of screening group of only cervical cancer was 38.9%, and the rate of non-screening group was 44.4%. 2.As to the screening pattern of cervical and breast cancer, there were significantly for age, income, occupation, married status, spouse, the factors associated with health promotion (doctor visiting, exercising), married age, number of children, and breast feeding(p〈0.05). 3.The factors associated with screening behaviors for cervical and breast cancers were age, income, occupation, married status, doctor visiting, exercising, married age, number of children, and breast feeding(p〈0.05). Based on the above-mentioned results obtained by this study, it was anticipated that this study may be play a vital role as basic data for the development and execution of cervical and breast cancers screening program for women in a community. And the analysis, done on the basis of the status of the cancer screening, of the influence factors on cervical and breast cancers screening behavior showed that for the development of a cancer screening program, the factors like age, social-economic class, married status, health promotion behavior, and reproductive characteristics should be considered.

WDM 시스템용 광대역 증폭기의 시뮬레이션

李鎬俊,沈雲用,鄭白鎬 湖西大學校工業技術硏究所 1999 工業技術硏究所論文集 Vol.18 No.-

In recent years, the biggest issue of WDM system is in increasing its bandwidth. Transmission bandwidth of WDM may be limited by many kinds of component, and the bandwidth plays impotent role in most of all optical amplifiers. Transmission bandwidth of recent WDM is limited in about 40 nm. This limit depends on EDFA(?? Fiber Amplifier) gain bandwidth. To overcome this problem, we may use L and S band using Yb/Nd doped fiber amplifier. Wideband amplifier, which is consisted of RFA for L band and EDFA for M band using single pump laser diode, is presented. The amplifiers have been analyzed numerically for the design.

일방성 GFRP 복합재료에서 음향방출 신호의 위치표정

이종오,원순호,윤운하,이종규,소철호 한국비파괴검사학회 2001 한국비파괴검사학회지 Vol.21 No.3

General source location method that use an arrival time differences among sensor is restricted to the composite material and the complex-shaped material. In this study, a bundle-type acoustic sensor composed of 6 pinducers was utilized to determine wave propagation direction and then to estimate source location of the unidirectional GFRP. For the purpose of the study, slowness curve for the material was obtained and made an assumption that the incident waves on pinducers are propagated as a plane wave. According to the results, measured propagation directions of the wave was coincide with theoretical background, however, it was a hassle to determine the source location exactly. But, it is expected that bundle-type sensor gives more accurate results for zone location than generally used acoustic sensors.