http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
이진우,이종철,윤서용,이문수 대한전자공학회 2004 電子工學會論文誌-TC (Telecommunications) Vol.41 No.3
In this paper, a wideband two-layer H-shaped microstrip antenna for WLAN is designed. To increase the bandwidth of microstrip patch antenna a configuration of stacked type using parastic element is used. Furthermore, to reduce the size of microstrip patch antenna, two techniques are employed . the first one is H-shaped patch type and the second one is that the main radiator and parastic patch are shorted to the ground plane using ten shorting posts. The antenna bandwidth and radiation characteristics are calculated by ENSEMBLE ver. 5.0 simulation software, and compared with the experimental results. Experiment results show that the bandwidth of antenna in 740MHz centered at 5.46㎓(13.5%), which is close agreement with the calculations, 770MHz(13%). Also, the antenna size can be reduced by 71.5% compared with the half wavelength rectangular microstrip antenna using the same substrate at the same frequency. 본 논문에서는 무선 근거리 지역 통신망(WLAN: Wireless Local Area Networks)용 광대역 2층 H-형 마이크로스트립 패치 안테나를 설계한다. 마이크로스트립 패치 안테나의 대역폭을 개선하기 위해서 기생패치를 부가하여 다층배열한다. 그리고 안테나의 크기를 줄이기 위해, 기본 방사소자와 기생패치는 10개의 단락봉으로 단락된 H-모양의 패치로 설계한다. 마이크로스트립 안테나는 모멘트법으로 작성된 ENSEMBLE ver 5.0의 소프트웨어를 사용하여 설계하고 실험치와 비교한다. 제작된 안테나의 대역폭은 5.46㎓에서 740㎒(13.5%)이며, 이것은 계산치 770㎒(13%)와 거의 근사하다. 또한 동일 주파수에서 동일 기판에 설계된 안테나 크기는 반파장 구형 마이크로스트립 패치 안테나에 비해 71.5%로 축소되었다.
3차원 트랜지션을 이용한 광대역 마이크로스트립 패치 안테나의 설계
정창권,강치운,윤서용,이봉석,김우수,이문수 한국정보통신학회 1999 한국정보통신학회논문지 Vol.3 No.2
본 논문에서는 유전율 1.06, 두께 $\lambda$/4인 발포체 기판상의 얇은 필름에 인쇄한 새로운 형태의 단일층 마이크로스트립 패치 안테나를 설계했다. 안테나의 대역폭이 광대역 임피던스정합을 얻기 위하여 3차원 트랜지션을 사용한다. 안테나의 방사패턴 및 반사손실, 전압정재파비는 "IE3D" 시뮬레이션 패키지를 사용하여 계산하여 측정결과와 비교했다. 측정 결과 전압정재파비 $\le$ 2:1 인 대역폭이 중심주파수 6.8 GHz에서 약 65%로 광대역 안테나임을 입증하였다. 그리고 반사손실 및 전압정재파비는 계산치와 실험치가 거의 일치하였다. 거의 일치하였다. In this paper, it is designed a new type single layer patch antenna which is printed on a very thin film and separated from the ground-plane by foam with a low permitivity of 1.06 and a high thickness of around quarter wavelength. It allows the use of three-dimensional transition, from one level to another, so that its bandwidth can be enhanced by wideband impedance matching. The radiation pattern, return loss, and VSWR of the antenna are calculated using "IE3D" simulation package, and compared with the experimental results. Experimental results show that the bandwidth is about 65% of center frequency 6.8 GHz, return loss and VSWR are in a fairly good agreement with the calculations.culations.
이진선,강치운,윤서용,이봉석,김우수,이문수 한국정보통신학회 1999 한국정보통신학회논문지 Vol.3 No.3
In this paper, it is designed a microstrip U-slotted patch antenna with double resonances to enhance the bandwidth. In the design of an U-slotted patch antenna, there are considered the input impedance, the width of patch, the total length of the slot, the height of foam, the position of the probe and the radius of feed pin. The broadband behavior of antenna can be obtained by adjusting the length and width of the slot. The radiation from the antenna is linear polarized with the E-paine parallel to the vertical slots and the H plane parallel to horizontal slot. The radiation pattern, impedance locus, and VSWR of the antenna are calculated using "ENSEMBLE" software, and compared with the experimental results. Experimental results show that the bandwidth for VSWR $\le$ 2:1 is about 28.6%, a directivity 14.18dBi at 6.040GHz. 6.040GHz. 본 논문에서는 대역폭을 향상시키기 위하여 이중공진을 갖는 마이크로스트립 U형 슬롯 패치 안테나를 설계 제작한다. U형 슬롯 패치 안테나를 설계하는데 있어서 입력 임피던스, 패치 폭, 슬롯의 전체길이, 발포형 유전체의 높이, 급전 위치 및 핀의 반경 등을 고려해야 한다. 안테나의 광대역 특성을 얻기 위해서는 슬롯의 폭과 길이를 조절한다. 안테나의 방사는 수직슬롯에 평행인 E면 패턴과 수평슬롯에 평행인 H면 패턴을 갖는 선형편파 특성을 갖는다. 안테나의 방사패턴, 임피던스 도표, 전압정재파비는 "ENSEMBLE"을 사용하여 계산하고 실험결과와 비교한다. 실험 결과 VSWR$\le$2:1인 임피던스 대역폭은 약 28.6%이며, 6.040GHz에서 지향성 이득은 14.18dBi 이다..18dBi 이다.