http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Kim S.H.,Park Y.J.,Hwang W.H.,Huang J.Y.,Honda Y.,Inoue Y. 한국진공학회 2006 Applied Science and Convergence Technology Vol.15 No.4
국제 직선형 충돌 가속기 (ILC; International Linear Collider). 자유전자 레이저 (FEL: Free Electron Laser)와 같은 차세대 가속기에 사용 할 공동형 빔위치 측정기 ( 공동형 BPM: cavity-type beam position monitor)를 일본 고에너지 연구소 (KEK; High Energy Accelerator Research Organization)와 공동으로 개발하였다. ILC 및 FEL의 운전을 위해서는 빔 기반 정렬 (beam-based alignment)과 되먹임 장치 (feedback system)가 필수적으로 요구되는데, 이를 위해서는 적절한 위치에 서브마이크론의 분해능을 지닌 빔위치 측정기를 설치하여야 한다 [1]. 공동형 BPM은 기계적인 정밀도에 매우 민감하므로 정밀한 제작과 미세한 기계적 조정을 통하여 성능을 달성하게 된다. 우리는 제작 오차를 줄이기 위하여 공진 공동, 빔 튜브, 도파관, 전기도입기 등 모든 부품을 조립 후 한꺼번에 진공 브레이징 하였다. 공동의 외주면에는 네 개의 튜닝 핀을 두어 공진주파수 및 x-y 격리도 (x-y isolation between coupled waveguide)를 미세 조정할 수 있도록 하였다. 현재 개발된 공동형 BPM 은 공진주파수는 6.422 GHz 이며, 공동 내경은 53.822 mm, 빔의 위치 측정 범위는 ${\pm}250 {\mu}m$이다. network analyzer를 관측하면서 튜닝핀을 이용하여 x-y 격리도를 -40 dB 이하로 조정할 수 있었다. 실제 KEK ATF2에서의 전자빔을 이용한 시험에서 신호의 모양, x-y 격리도, 민감도 등에서 만족한 결과를 얻었다. Cavity-type beam position monitors were developed in collaboration with KEK to use for the future accelerators such as international linear collider (ILC) or x-ray free electron laser (XFEL) in PAL. BPM components such as BPM cavity, beam tubes, waveguides and feedthroughs were assembled by brazing at the same time to reduce mechanical errors during the fabrication. There are four screwed pins around outer rim of the cavity for the tuning of cavity frequency and x-y isolation. The resonance frequency of BPM is 6.422 GHz, the inner diameter of cavity is 53.822 mm, and the range of mechanical adjusting is $+ / - 250{\mu}m$. The x-y isolation was measured better than -40 dB after tuned. Test results of signal forms, x-y isolations, sensitivities are satisfied within requirements for the KEK ATF2 beam line.
Changes of Serum Mineral Concentrations in Horses during Exercise
Inoue, Y.,Osawa, T.,Matsui, A.,Asai, Y.,Murakami, Y.,Matsui, T.,Yano, H. Asian Australasian Association of Animal Productio 2002 Animal Bioscience Vol.15 No.4
We investigated the exercise-induced changes in the serum concentration of several minerals in horses. Four welltrained Thoroughbred horses performed exercise for 5 d. The blood hemoglobin (Hb) concentration increased during exercise, recovered to the pre-exercise level immediately after cooling down and did not change again up till the end of experiment. The changes in serum zinc (Zn) and copper (Cu) concentrations were similar to those of blood Hb during the experiment. The serum magnesium (Mg), inorganic phosphorus (Pi) and iron (Fe) concentrations also increased during exercise. Though the serum Pi concentration recovered to the pre-exercise level immediately after the cooling down, it decreased further before the end of the experiment. The serum Mg concentration was lower immediately after cooling down than its pre-exercise level but gradually recovered from the temporal reduction. The recovery of the serum Fe concentration was delayed compared to that of other minerals and recovered 2 h after cooling down. The serum calcium (Ca) concentration did not change during exercise but rapidly decreased after cooling down. As a result, it was lower immediately after cooling down than its pre-exercise level. It recovered, however, to the pre-exercise level 2 h after cooling down. The temporal increase in the serum concentrations of all minerals except Ca is considered to result from hemoconcentration induced by exercise and the stable concentration of the serum Ca during exercise is possibly due to its strict regulation of homeostasis. These results indicate that the serum concentration of each mineral responds differently to exercise in horses, which may be due to the difference in metabolism among these minerals.
김승환,박용정,황운하,황정연,Y. Inoue,Y. Honda 한국진공학회 2006 Applied Science and Convergence Technology Vol.15 No.4
Cavity-type beam position monitors were developed in collaboration with KEK to use for the future accelerators such as international linear collider (ILC) or x-ray free electron laser (XFEL) in PAL. BPM components such as BPM cavity, beam tubes, waveguides and feedthroughs were assembled by brazing at the same time to reduce mechanical errors during the fabrication. There are four screwed pins around outer rim of the cavity for the tuning of cavity frequency and x-y isolation. The resonance frequency of BPM is 6.422 GHz, the inner diameter of cavity is 53.822 mm, and the range of mechanical adjusting is +/- 250 ㎛. The x-y isolation was measured better than -40 dB after tuned. Test results of signal forms, x-y isolations, sensitivities are satisfied within requirements for the KEK ATF2 beam line. 국제 직선형 충돌 가속기 (ILC; International Linear Collider), 자유전자 레이저 (FEL: Free Electron Laser)와 같은 차세대 가속기에 사용 할 공동형 빔위치 측정기 (공동형 BPM : cavity-type beam position monitor)를 일본 고에너지연구소 (KEK; High Energy Accelerator Research Organization)와 공동으로 개발하였다. ILC 및 FEL의 운전을 위해서는 빔 기반 정렬 (beam-based alignment)과 되먹임 장치 (feedback system)가 필수적으로 요구되는데, 이를 위해서는 적절한 위치에 서브마이크론의 분해능을 지닌 빔위치 측정기를 설치하여야 한다 [1]. 공동형 BPM은 기계적인 정밀도에 매우 민감하므로 정밀한 제작과 미세한 기계적 조정을 통하여 성능을 달성하게 된다. 우리는 제작 오차를 줄이기 위하여 공진 공동, 빔 튜브, 도파관, 전기도입기 등 모든 부품을 조립 후 한꺼번에 진공 브레이징 하였다. 공동의 외주면에는 네 개의 튜닝 핀을 두어 공진주파수 및 x-y 격리도 (x-y isolation between coupled waveguide)를 미세 조정할 수 있도록 하였다. 현재 개발된 공동형 BPM은 공진주파수는 6.422 GHz이며, 공동 내경은 53.822 mm, 빔의 위치 측정 범위는 ±250 ㎛이다. network analyzer를 관측하면서 튜닝핀을 이용하여 x-y 격리도를 -40 dB 이하로 조정할 수 있었다. 실제 KEK ATF2에서의 전자빔을 이용한 시험에서 신호의 모양, x-y 격리도, 민감도 등에서 만족한 결과를 얻었다.
Inoue, Y.,Kuramoto, Y.,Hattori, M.,Adachi, M.,Kimura, M.,Akahane, T. The Korean Infomation Display Society 2011 Journal of information display Vol.12 No.3
Alignment failure sometimes occurs during the rubbing process because the rubbing cloth comes in direct contacts with the surface of the alignment film. A number of researches observed and evaluated the surface of the alignment film after the rubbing process had been reported. The real-time rubbing process has not been observed directly yet, though. In this study, the movement of the piles of the rubbing cloth during the rubbing process was observed with a high-speed camera. Furthermore, the relationship between the rubbing scratch on the alignment films and the movement of the pile was investigated. It was found that the movement of the pile affected the rubbing scratches.
Y. Inoue,Y. Kuramoto,M. Kimura,M. Hattori,M. Adachi,T. Akahane 한국정보디스플레이학회 2011 Journal of information display Vol.12 No.3
Alignment failure sometimes occurs during the rubbing process because the rubbing cloth comes in direct contacts with the surface of the alignment film. A number of researches observed and evaluated the surface of the alignment film after the rubbing process had been reported. The real-time rubbing process has not been observed directly yet, though. In this study, the movement of the piles of the rubbing cloth during the rubbing process was observed with a high-speed camera. Furthermore,the relationship between the rubbing scratch on the alignment films and the movement of the pile was investigated. It was found that the movement of the pile affected the rubbing scratches.