http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
가공온도에 따라 다이업셋한 Nd-Fe-B-Cu합금의 응력과 결정에 관한 연구
박정덕,양현수,곽창섭,정원용 ( J . D . Park,H . S . Yang,C . S . Kwak,W . Y . Jeung ) 한국열처리공학회 1994 熱處理工學會誌 Vol.7 No.1
This study is to investigate the stress distributions, crystal orientations and magnetic properties during die-upsetting according to working temperature of Nd-Fe-B-Cu alloys. The stress distributions in the specimens during compressing process were calculated by a finite element method program(SPID). The calculated stresses were effective stress(σ_(eff)), compression stress(σ₂), radial direction stress(σ₁) rotational direction stress(σ_e) and shear stress(τ_(12)). The stress distributions of σ₂obtained by a computer simulation showed that the stress components causing the magnetic alignment during die-upsetting of the cast magnets were very high at the center-part of a specimen, and decreased toward the periphery-part of a specimen. In view of the above results the magnetic properties should be better at the center-part of a specimen than any other parts. But the measured magnetic properties were better at the mid-part. These results should be due to the fact that the specimens were casted. Normally the magnetic properties are affected by the casting process as well as by the stress levels. σ₁, σ_e, are thought to affect the liquid phase flowing and domain patterns, respectively. The influence of τ_(12) was trivial, σ_(eff) distributed similar throughout the specimen. The Nd-rich phase appeared at the peripheral of the specimen where the stress level of σ₁, σ₂was low or the stress level of σ_e was high. The Nd-rich phase was squeezed out during die-upsetting. This phase had an effect on the crystal orientation and grain growth. The stress distributions of alloy were irregular at the parts of the specimen where the die contacted with specimen.
박정덕(D. Park),이도원(D. W. Lee),하현규(H. K. Ha),김종봉(J. B. Kim) Korean Society for Precision Engineering 2021 한국정밀공학회 학술발표대회 논문집 Vol.2021 No.11월
중형 및 소형 냉동기의 압축기에는 Reed 밸브가 주로 사용된다. Reed 밸브는 압축기의 수명 동안 파손이 없어야 하고, 흡입 및 압축 과정에서 냉매의 흐름을 제어하기 때문에 성능에 크게 영향을 준다. 그렇기 때문에 밸브의 거동을 정확하게 예측하고 설계하는 것이 매우 중요하다. 본 연구에서는 압축기 신뢰성 및 성능 해석을 정확하기 하기 위해 밸브 열림량에 따른 유량과 밸브에 작용하는 힘을 전산유체해석을 통해서 분석하였다. 밸브의 열림량을 달리하면서 입구와 출구의 압력 차이에 의한 냉매의 유량과 밸브에 작용하는 힘을 예측하였다. 입구와 출구의 압력 차이와 밸브의 열림 높이에 대해 여러 해석을 수행하여 결과를 분석하였다. 유량은 밸브의 열림이 커질수록 증가하지만, 밸브의 열림 높이가 포트 반경의 0.5 이상인 경우는 증가 속도가 작아짐을 알 수 있었다. 밸브에 가해지는 힘은 압력 차이에 비례하여 증가하고, 밸브의 열림 높이가 증가함에 따라서는 작아짐을 알 수 있었다. 밸브 열림 높이가 포트 반경의 0.6 배 이상인 경우 밸브에 작용하는 힘의 감소가 작아짐을 알 수 있었다. 본 연구 결과는 밸브의 거동 및 성능 해석을 수행하는 데 유용하게 활용이 될 것으로 판단된다.
기계적 분쇄한 Nd - Fe - B 합금의 다이업셋과 열처리가 자기적 특성에 미치는 영향
정원용(W. J. Jeung),박정덕(J. D. Park),곽창섭(C. S. Kwak),양현수(H. S. Yang) 한국자기학회 1994 韓國磁氣學會誌 Vol.4 No.3
The effect of die upset and heat treatment on the magnetic properties of mechanically ground Nd_(16)Fe_(78)B_6 alloys has been studied. Although stripe domain patterns parallel to the compression direction were observed after die upset, it was found that crystallographic c-axes of a specimen were not completely aligned along the compression direction, which resulted in the decrease of Br. The average grain size of a die-upset specimen annealed for 5 hours at 1000℃ was about 20 ㎛, resulting in reduced values of Br and iHc. The maximum magnetic properties(Br=7. 8 kG and iHc = 14 kOe) were obtained from the magnet die-upset at 750℃ using the alloy powder ground for 13 hours.