http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
IR-UWB를 이용한 빔 스캐닝 배열 안테나 설계 및 연구
김근용(Keun-Yong Kim),강은균(Eun-Kyun Kang),김진우(Jin-Woo Kim),나극환(Keuk-Whan Ra) 대한전자공학회 2014 전자공학회논문지 Vol.51 No.3
본 논문에서는 TRM(Transmitter-Receiver Module)을 사용하여 각 안테나에 펄스의 위상을 조정함으로써 빔 패턴 각도를 조정하여 다중 경로 환경에서의 성능저하를 향상시킬 수 있다. 다중 경로 환경에서 성능저하를 향상시키는 임펄스 신호를 왜곡 없이 송·수신하는 빔 스캐닝 시스템(Beam Scanning System)을 설계 및 제작 하였다. 빔 스캐닝 시스템은 안테나 종단 부분에서 신호가 왜곡 없이 송·수신이 가능하여 하며 타 시스템에 영향을 미치지 않아야 한다. 또한 빔 조향을 통하여 표적에 대한 감지 능력도 있어야 한다. 설계한 빔 스캐닝 안테나의 분산특성은 충실도(Fidelity)를 사용하여 분석을 하고 조향과 레이더 해상도(Radar Resolution) 성능은 1 cm × 1cm 표적의 크기를 사용하여 그 성능을 확인한다. 빔 스캐닝 배열 안테나를 제작하기 위해 IR-UWB(Impulse Radio)용 비발디 안테나(Vivaldi Antenna), 삼중대역 윌킨슨 전력 분배기(Tri-Band Wilkinson power divider), TRM(Transmitter-Receiver Module), 송·수신 모듈(TRM)을 컨트롤 할 수 있는 컨트롤 보드 및 GUI 설계를 하였다. 본 연구를 통해 개발된 UWB 빔 스캐닝 시스템은 빔 패턴 각도를 조정하여 다중 경로 환경에서의 성능저하를 향상시킬 수 있으며, 네트워크 분석기를 이용한 시간영역 분석기술은 안테나 설계 시 안테나의 특성을 정확히 분석을 할 수 있고 손쉽게 빔 폭을 확인 할 수가 있다. 설계한 빔 스캐닝 시스템은 레이더 응용 분야인 지표투과 레이더, 벽 투과 레이더, 의료영상 레이더, 탐색 및 구조 레이더, 비파괴 탐상 레이더 및 무선통신 시스템에 사용 적용이 가능하다. This paper is able to be solved by improving degradation in multi-path environment by adjust beam pattern angle through modifying pulse phase of each antennas by using TRM (Transmitter Receiver Module). Beam Scanning Array Antenna, which is transmitter/receiver that improves degradation in multi-path environment without any signal distortion, is designed and manufactured. Beam Scanning Array Antenna should be able to send/receive signal at the antenna’s longitudinal part without distortion and should not influences other systems. Also, it should include target detecting ability by beam steering.Dispersion characteristic of Beam Scanning Antenna, which is designed, is analysed by using fidelity, and steering and radar resolution performance is verified by using 1 cm × 1 cm sized target. To manufacture Beam Scanning Array Antenna, control board and GUI, which is able to control Vivaldi Antenna for IR-UWB, Tri-Band Wilkinson power divider, and TRM (Transmitter Receiver Module), is designed. Throughout this research, developed Beam Scanning UWB Array Antenna system is adoptable for radar application field. and time domain analysis techniques by using network analyser made the antenna characteristics analysis for setting up antenna more accurate. In addition, it makes beam width checking without difficulties.
군 지연 및 충실도를 이용한 IR-UWB용 테이퍼 슬롯 안테나 방사패턴 분석
김근용(Keun-Yong Kim),고영목(Yong-Mok Ko),박경진(Kyoung-Jin Park),강은균(Een-Kyun Kang),이대우(Dae-Woo Lee),박종현(Jong-Hyun Park),나극환(Keuk-Whan Ra) 대한전자공학회 2013 전자공학회논문지 Vol.50 No.8
본 논문에서는 IR-UWB를 위한 테이퍼 슬롯 안테나를 Ansoft인 HFFS을 사용하여 설계 및 제작 하였고 안테나의 군 지연 및 충실도를 사용하여 광대역 안테나의 빔 폭에 대해 연구를 제안하였다. 이를 위해 Network Analyzer에서 획득한 데이터를 Chirp Z-transform을 사용하여 시간영역에서의 분석을 하였고 시뮬레이션은 CST microwave studio를 이용하여 이를 확인 하였다. 안테나의 방사패턴의 분석은 두 안테나를 0.5 미터 간격으로 이격시킨 후 송신 안테나를 고정 후 수신 안테나를 10° 간격으로 360° 회전하여 각각의 충실도를 획득하여 안테나의 성능 분석하였다. 분석한 결과 ±40° 미만일 경우 90%이상의 양호한 충실도를 얻었고 ±40° 이상은 90%이하의 낮은 결과를 얻었다. 이러한 충실도를 이용한 방사패턴을 사용함으로 광대역 안테나의 빔 폭을 보다 정확한 분석을 할 수 있다. In this paper, Tapered slot antenna of IR-UWB was Designed and fabricated using HFSS and we suggest the beam width of the broadband antenna using group-delay and fidelity. For this purpose, acquired data from the Network Analyzer was analyzed in the time domain by using the chirp-Z transform and Simulation was conducted and confirmed with the CST microwave studio. Analysis of the antenna radiation pattern is the antenna separation at intervals of 0.5 metres and then transmit antenna is fixed and the receiving antenna 360 degree intervals of 10 degree each, The results of the analysis are as follows, and analyzer of the fidelity of the antenna"s performance. An analysis of more than 90 percent of the cases is less than ± 40 degrees in good fidelity, more than 90% less than ± 40 degrees and lowe fidelity. In conclusion, Analysis of Beam width of wideband antenna with more precise is possible through using these radiation pattern using fidelity
박경진(Kyoung-Jin Park),이대우(Dae-Woo Lee),고영목(Yong-Mok Ko),강은균,박종현(Jong-Hyun Park),김근용(Keun-Yong Kim),나극환(Keuk-Whan Ra) 대한전자공학회 2013 전자공학회논문지 Vol.50 No.9
본 논문에서는 USB(Universal Serial Bus) 케이블 전원선에서의 방사성 EMI(Electro-Magnetci Interference) 개선 방안을 제시한다. 케이블 전원선에서의 EMI 방사현상을 확인하기 위해 무선 비디오 액세스 시스템을 이용하여, 방사성 EMI 결과를 분석하고 초기 측정 결과 규제치 대비 약 3 [dBuV/m] ~ 15 [dBuV/m]를 초과함을 확인한다. 방사성 EMI 원인 분석을 위해, 먼저 USB 케이블 전원선에서의 S-파라미터 측정을 수행하여 케이블의 고주파수대역에서의 규칙적인 공진현상과 방사성 EMI 주파수의 연관성을 분석한다. 그리고, 전원 회로 임피던스 관리 기법을 응용하여 캐패시터의 개수 선정, 비드를 이용한 저역 통과 대역 필터를 구성을 통해 케이블 전원선의 공진현상을 저감하는 개선방법을 적용한다. 결론적으로 개선된 회로를 시스템에 적용하여 케이블의 규칙적 공진의 저감방법을 제시하여, 방사성 EMI 테스트 결과 규제치 대비 약 3 [dBuV/m] ~ 20[dBuV/m] 마진의 마진을 확보하여 제시한 방법의 적합성 확인한다. In this paper, we studied on improvement for radiated EMI of USB power line of cable. it is made by using wireless video access point system for confirming the phenomenon of radiated EMI from cable. then, we make sure that the limit exceed through the initial measurement of radiated EMI limit criteria in comparison to about 3 [dBuV/m] ~ 15 [dBuV/m]. after that we confirmed the resonance in power line of cable through measurement of s-parameters. so, we confirmed the relation radiated EMI and power line of cable resonance and we reduced radiated EMI in power line of cable through a capacitor and low pass-band filter using the technique of power networks management. in conclusion, we suggested how to reduce power line of cable resonance applied for the improved method. and we confirmed that suggested reduction method is suitable through testing radiated EMI. the result of radiated EMI reduction limit criteria 40[dBuV/m] ~ 47[dBuV/m] in comparison to about 3 [dBuV/m] ~ 20 [dBuV/m].