http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
전산화단층촬영용장치의 모의 평가를 통한 평가방법 및 평가기준의 개선방안에 관한 연구
김교태(Kyo-Tae Kim),허예지(Ye-Ji Heo),신정욱(Jung-Wook Shin),노시철(Si-Cheul Noh),정봉재(Bong-Jae Jung),강상식(Sang-Sik Kang),남상희(Sang-hee Nam),박지군(Ji-Koon Park) 한국방사선학회 2013 한국방사선학회 논문지 Vol.7 No.5
국외의 경우 의료기기의 품질보증(QA)의 중요성이 대두되고 있으나, 국내의 경우 품질보증 평가기준이 명확하게 제시되어 있지 않다. 이에 본 연구에서는 국내ㆍ외 문헌 조사 및 비교 및 분석을 통하여 개선된 새로운 품질보증 평가기준 및 평가방법을 제시하고자 하였으며, 모의 평가 수행을 통하여 적합성을 확인하였다. 국내의 문헌 조사 결과, 다수의 항목이 주관적인 평가 방법을 이용하고 있으며, 정확성 및 재현성 평가로는 부족한 횟수로 측정을 수행하고 있다. 따라서 문제점들을 해결하기 위하여 객관적인 평가 방법 및 명확한 기준을 제시하고자 하였으며, 측정 횟수를 10회로 하여 정확성 및 재현성에 대하여 고려하였다. 모의 평가 결과, 제시한 평가 기준 및 평가방법에 모두 만족하는 것을 확인하였다. 그러나 국내에서만 시행하고 있는 항목과 고대조도 공간분해능에 대해서는 적합한 평가 기준 및 평가 방법을 정립하지 못하였다. 차후 국내 실정에 맞게 정립 연구가 필요할 것으로 사료된다. In foreign countries, the impotance of quality assurance (QA) is increasing, whereas QA evaluation standards are not established properly in Korea. Thus this study was conducted to suggest improved QA evaluation standards and methods by studying/comparing/analyzing the literature in both Korea and foreign countries and prove its suitability through simulated evaluation. result of research in south korea, much check list using the evaluation method subjective, the evaluation of accuracy and reproducibility is meausred in the number of missing. Therefore, attempts to present a clear reference evaluation and objective way to solve the problem, examined the accuracy and reproducibility and 10times of measurement. The results of the simulated evaluation satisfied both proposed evaluation standards and methods. However the QA evaluation standards and methods for the items that are implemented only in Korea and high-contrast spatial resolution could have been established. In this regard, there is a need of further studies on the establishment of QA evaluation standards and methods that suits Korean situation.
초음파 치료용 비집속 변환기의 구동 조건에 따른 음향 출력 평가
김한솔(Han-Sl Kim),최일홍(Il-hong Choi),박지군(Ji-koon Park),강상식(Sang-sik Kang),박형후(Hyong-hu Park),정봉재(Bong-jae Jeong),노시철(Si-cheol Noh) 한국방사선학회 2015 한국방사선학회 학술대회 논문집 Vol.2015 No.추계
본 연구에서는 초음파 캐비테이션 현상을 이요한 초음파 치료를 위한 기초 연구로써, 초음파 구동 신호의 형태에 따른 음향 출력의 변화를 관찰하였다. 선행 연구를 통하여 제작된 중심 주파수가 1.5MHz의 고출력 단일 초음파 변환기를 이용하여 양의 펄스와 부의펄스, 양의 버스트와 부의 버스트 구동 신호에 따른 출력을 평가하였으며, 연속 사인파와 연속 사각파에 따른 차이를 비교하였다. 본 연구를 통하여 각 구동 신호에 따른 초음파 음향 출려과 이에 따른 캐비테이션 발생량을 평가할 수 있었으며, 본 연구의 결과는 초음파 치료 시 구동 조건 결정에 기초 자료로 활용될 것으로 판단된다. In this study, as a basic research for an ultrasonic treatment using the ultrasonic cavitation it was observed a change in the acoustic output according to the type of the transducer excitation signal. The acoustic outputs of the positive and negative pulse, positive and negative burst driving signals were evaluated. by using the fabricated 1.5 MHz high power single ultrasonic transducer. In addition, the difference between continuous sine wave and square wave were discussed. As the results of this stduy, the acoustic outputs and the cavitation yields trends were confirmed according to the each excitatoin condition. And these result are thought be useful to decide the driving condition.
형광체 두께와 입자 크기에 따른 희토류 증감지의 화질 영향 연구
김한솔(Kim han-sol),최수림(Choi su-rim),정봉재(Jung Bong Jae),강상식(Kang sang-sik),박지군(Park ji-koon) 한국방사선학회 2015 한국방사선학회 학술대회 논문집 Vol.2015 No.춘계
본 연구는 기존의 CMOS센서에 적용 가능하도록 침전법을 이용해 Gd2O2S:Tb 형광체필름을 제작하고, 형광체 입자크기와 형광체 필름 두께의 변화에 따른 화질 영향을 Contrast method을 이용하여 MTF값으로 평가하였다. 제작된 필름은 CMOS 센서에 접합하여 CMOS 기반의 X선 검출기를 제작하였다. 이를 이용해 제작한 형광체 필름의 영상을 획득하고 기존 상용화된 Rad-icon CMOS 센서에서 영상을 획득하여 비교 분석하였다. 그 결과 형광체의 particle size가 작을수록, 형광체 필름의 두께가 얇을수록 기존 상용화된 제품에 비해 높은 MTF 값을 획득할 수 있었다. 입자크기에 따른 MTF 평가에서는 2 lp/mm 공간주파수에서의 기존 상용화 제품 MTF값이 0.6에 비해, 본 연구에서 제작한 2.5㎛ 형광체 입자는 0.71로 높게 평가되었다. 또한 형광체 필름의 두께에 따른 해상력 평가 결과는 120㎛에서 0.82, 150㎛ 두께에서 0.71 및 210㎛ 두께에서 0.59로 형광체 필름 두께가 증가할수록 MTF 값이 감소하는 것으로 나타났다. 또한 이는 상용화된 Rad-icon CMOS 센서(형광체 두께 150㎛)의 0.6에 비해 본 연구에서 제작한 2.5㎛ 입자크기, 150㎛ 형광체 두께의 형광체 필름에서 0.71로 다소 높게 측정되었다. This research used precipitation method to produce Gd2O2S:Tb phosphor film to be used for existing CMOS sensor and assessed the effect its particle size and film thickness on screen quality in terms of MTF value using the contrast method. The phosphor film produced was combined with commercialized CMOS-based sensor to produce an image, which was in turn compared to the image made by Rad-icon CMOS sensor. According to the result, the smaller the particle size and the thinner the phosphor, the higher the quality of MTF values compared to the existing commercialized products. In the MTF assessment according to particle size, MTF value under 2 lp/mm space frequency was 0.6 for commercialized product while 0.71 for phosphor with 2.5㎛ thickness made in this research. In the assessment of resolution according to phosphor film thickness, the value was 0.82 under 120㎛, 0.71 under 150㎛ and 0.59 under 210㎛, showing that an increase in phosphor film thickness resulted in decline in MTF value. Also, compared to the value of 0.6 in the commercialized Rad-icon CMOS sensor (phosphor thickness of 150㎛), the value was 0.71, a little higher, in phosphor with 2.5㎛ particle size and 150㎛ thickness.
김교태(Kyo Tae Kim),한무재(Moo Jae Han),허예지(Ye Ji Heo),김주희(Joo Hee Kim),강상식(Sang Sik Kang),박지군(Ji Koon Park),남상희(Sang Hee Nam) 한국방사선학회 2016 한국방사선학회 논문지 Vol.10 No.5
선량 크리프는 임상적 오류 중 하나로 검사자의 미숙 또는 부주의에 기인하여 발생하는 현상으로 AAPM Task Group #116에 의하면 디지털 방식의 시스템에서 지속적인 발생이 보고되고 있다. 이러한 현시점에서 선량 크리프 현상을 최소화할 뿐만 아니라 재현성 향상이 가능한 자동노출제어장치의 요구가 증가하고 있다. 이에 본 연구에서는 제작이 쉬울 뿐만 아니라 고효율 반도체 센서에 대한 연구를 수행함으로써 선량 크리프 현상을 저감할 수 있는 자동노출제어장치의 센서에 대하여 고찰하고자 하였다. 연구 수행 결과, 제작된 I형 센서 및 PIN형 센서의 경우 Ref 센서와 비교하면 광학적 특성이 우수하여 음영효과가 적게 나타날 것으로 사료되고, 대체로 낮은 민감도 특성이 나타나지만, 조사 조건 변화에 따른 일정한 추세를 가짐으로써 정확한 피드백 신호를 자동노출제어장치에 제공할 수 있을 것으로 사료된다. Dose creep is one of clinical errors that arises from the tester’s inexperience or carelessness, and according to Task Group #116 of American Association of Physicists in Medicine, its continued occurrence is being reported in the digital method. At this point, the demand for an automatic exposure control device that minimizes the dose creep phenomenon and can improve reproducibility is increasing. In this study is to consider the automatic exposure control device sensor that can is not only easy to produce, but also reduce the dose creep phenomenon by conducting a research on high-efficient semiconductor sensor. As a result, the Intrinsic-type and PIN-type sensors have excellent optical property compared to Ref sensor, would have less shading effect, and have relatively low sensitivity, but would provide accurate feedback signals to automatic exposure control device with its consistent tendency according to exposure condition changes.
The Effects of Image Quality due to Scattering X-ray according to increasing Patient Thickness
Ji-Koon Park(박지군),Sung-Woo Yang(양승우),Jae-Hoon Jun(전제훈),Su-Yeon Cho(조수연),Kyo-Tae Kim(김교태),Ye-Ji Heo(허예지),Sang-Sik Kang(강상식) 한국방사선학회 2017 한국방사선학회 논문지 Vol.11 No.7
본 연구에서는 피사체 두께 증가에 따른 산란선 발생이 의료 영상화질에 미치는 영향을 정량적으로 분석하기 위한 연구를 수행하였다. 기존 병원에서 검사빈도가 높은 흉부를 조직등가물질로 제작한 미국표준 협회(ANSI; American National Standards Institute) 팬텀을 이용하여 피사체 두께가 증가함에 따라 발생하는 산란선 비율을 MCNPX 전산모사 하였으며, 실제 측정값과의 비교 분석을 수행하였다. 또한 피사체 두께 증가에 따라 획득된 X선 영상을 이용하여 RMS 입상성 평가, RSD 및 NPS 분석을 통해 산란선 발생 증가 에 따른 화질 영향을 평가하였다. 흉부 팬텀위에 두께 1 인치의 아크릴 팬텀을 추가적으로 증가시키면서 분석한 결과, 표준 두께인 6.1 inc h에서 산란선 비율은 48.9 %를 기준으로 1 인치 증가시마다 57.2 %, 62.4 %, 66.8 %로 증가하는 것으로 나타났으며, 이는 MCNPX 모의실험과 실제 측정한 산란선량은 유사한 결과를 보였다. 획득한 영상의 RMS 측정 결과, 피사체 두께가 증가함에 따라 표준편차가 낮아지는 값으로 도출되었다. 하지만 이를 평균 입사 선량을 고려한 RDS 분석에서는 6.1 inch에서 0.028, 7.1 inch의 경우 0.039, 8.1 inch 경우 0.051 및 9.1 inch에 서 0.062으로 증가하는 결과를 나타났다. 이는 피사체 두께 증가에 따른 산란선 발생 증가가 신호대 잡음비를 감소시킨다는 것을 알 수 있었다. 또한 검출기에 입사한 산란선 분포만 이용하여 측정한 NPS 결과에서도 피사체 두께가 증가할수록 노이즈가 증가하는 결과로 도출되었다. In this study, scattering factors affecting the quality of medical images were quantitatively analyzed and investigated. MCNPX simulation was conducted by using ANSI phantom, made of tissue equivalent materials, to calculate the scattering ratio occurred by the increase of the object thickness. Then, the result of the simulation was compared with the result of actual radiation measurement. In addition, we evaluated the image quality by the RMS evaluation, RSD and NPS analysis using X-ray images acquired with increasing object thickness. Furthermore, the scattering ratio was analyzed by increasing the thickness of acrylic phantom on chest phantom. The result showed that the scattering ratio was increased to 57.2%, 62.4%, and 66.8% from 48.9%, respectively, when the acrylic phantom thickness was increased by 1 inch from 6.1 inches. The results of MCNPX simulation and the actual measured scattering dose showed similar results. Also, as a result of RMS measurement from acquired x-ray images, the standard deviation decreased as the object thickness increased. However, in the RSD analysis considering the average incident dose, the results were increased from 0.028 to 0.039, 0.051, 0.062 as the acrylic phantom thickness was increased from 6.1 inches to 7.1 inch, 8.1 inch, and 9.1 inch, respectively. It can be seen that the increase of the scattering effect due to the increase of the object thickness reduces the SNR. Also, the NPS results obtained by measuring scattered radiation incident on the detector resulted in the increase of the noise as the object thickness increased.
서정,이제훈,김정오,정군석,정해용,Suh, Jeong,Lee, Jae-Hoon,Kim, Jeng-O,Chung, Koon-Seok,Jeong, Hae-Yong 한국군사과학기술학회 2007 한국군사과학기술학회지 Vol.10 No.3
Laser welding process for wing of a guided weapon is studied. Nd;YAG pulse laser beam is used to weld the skin(STS304, thickness: 1mm) to frame(AMS 5398) of wing. Optimal laser welding condition is obtained from the mechanical testing and observation of the welded joint.
하이브리드 로켓 추진장치 연소 열원을 이용한 절단기초실험
유덕근(Doc-Koon Yoo),김수종(Soo-Jong Kim),김진손(Jin-Kon Kim),구자예(Ja-Ye Koo),문희장(Hee-Jang Moon),이보영(Bo-Young Lee),길성망(Seong-Mahn Kil),오재영(Jae Young Oh),국태송(Tae-Seung Kuk) 대한기계학회 2003 대한기계학회 춘추학술대회 Vol.2003 No.11
The purpose of this study is to ascertain the ability of New type cutter using Hybrid Rocket Propulsion System<br/> to cut normal carbon steel and also compound metal like stainless steel which cannot be cut by regular<br/> oxygen-acetylene cutter. To compare cutting performance, Two different types of experiment with<br/> oxygen-acetylene and Hybrid Combustion cutters were performed.<br/> As a result, Hybrid Combustion cutter is used to cut both carbon steel and stainless steel with cutting speed of<br/> 400mm/min(carbon steel) and 250mm/min(stainless steel). Otherwise, oxygen- acetylene cutter can be used to cut<br/> only carbon steel with cutting speed of 500 ~ 700mm/min. The possibility of Hybrid Combustion cutter as a<br/> cutting machine was confirmed.