지속가능한 콘크리트의 개발을 위한 에코효율성 평가방법 제안

김태형,채창우,Kim, Tae-Hyoung,Chae, Chang-U 한국건설순환자원학회 2016 한국건설순환자원학회지 Vol.11 No.4

선천성 영아 섬유육종

김태형,정재희,송영택,Kim, Tae-Hyoung,Chung, Jae-Hee,Song, Young-Tack 대한소아외과학회 2004 소아외과 Vol.10 No.1

A newborn male baby was transferred to our hospital with a left inguinal mass. The mass was huge measuring $10{\times}10cm$, engorged, and dark-blue colored as a result of internal hemorrhage. Unstable vital signs were combined with DIC and acute renal failure. Emergency operation was performed because of the suspicion of bowel perforation. The peritoneal cavity was full of ascitis and the distal jejunum had a 0.5 cm perforation. Segmental resection of the jejunum and incisional biopsy of the inguinal mass were performed. On pelvic and thigh MRI, the mass protruded into pelvic cavity and encircled large vessels and nerves of the thigh. Pathologic diagnosis was congenital infantile fibrosarcoma. Fifteen days after operation, primary tumor excision was undertaken. The second look operation, performed after 6 times VAC chemotherapy, revealed no remained malignant cell on microscopic section. The baby has been followed closely for the last eight months.

Glass Fiber Post와 Composite Resin Core의 전단결합강도

김태형,심준성,이근우,Kim Tae-Hyoung,Shim June-Sung,Lee Keun-Woo 대한치과보철학회 2005 대한치과보철학회지 Vol.43 No.4

Statement of problem : Fracture of composite resin core will be occulted by progress of crack. Bonding interface of different materials has large possibility of starting point of crack line. Therefore, the bond strength of glass fiber post to composite resin core is important for prevention of fracture. Purpose: This in vitro study tried to find out how to get the higher strength of glass fiber post to composite resin core through surveying the maximum load that fractures the post and cote complex. Materials and methods: 40 specimens made with glass fiber Posts(Style $post^{(R)}$, Metalor, Swiss) and composite resin core ($Z-100^{(R)}$, 3M, USA) were prepared and loaded to failure with push-out type shear-bond strength test in a universal test machine. The maximum fracture load and fracture mode were investigated in the specimens that were restored with four different surface treatments. With the data. ANOVA test was used to validate the significance between the test groups, and Bonferroni method was used to check if there is any significant statistical difference between each test group. Evely analysis was approved with 95% reliance. Results: On measuring the maximum fracture load of specimens, both the treatments of sandblasted and acid-etched one statistically showed the strength increase rather than the control group (p<0.005). The scanning electric microscope revealed that sand blasting made more micro-retention form not only on the resin matrix but on the glass fiber, and acid-etching contributed to increase in surface retention form, eliminated the inorganic particles in resin matrix. Specimen fracture modes investigation represented that sand blasted groups showed lower bonding failure than no-sand blasted groups. Conclusion: Referring to the values of maximum fracture load of specimens, the bonding strength was increased by sand blasting and acid-etching.

대단면 급속시공을 위한 최적의 곡면막장형상개발에 관한 현장실험

김태형,윤지선,Kim, Tae-hyoung,Yoon, Ji-sun 한국터널지하공간학회 2006 터널기술 Vol.8 No.1

기존의 NATM과 같은 터널공법에서는 불착 직후 벽연은 숏크리트나 록볼트에 의하여 지지되기 때문에 재래공법과 비교하여 암반의 느슨함을 감소시킬 수 있으나, 막장은 통상 무지보 상태로 놓여있기 때문에 붕괴의 위험성을 항상 내포하고 있는 것이 현실이다 현재 국내 터널시공시에는 막장이 굴진방향에 직립합A로써 응력의 집중이 발생하며 또한 막장의 안정성을 우려하여 단연분할공법을 채택하는 것이 일반적 공법으로 되어왔다. 그러나 이러한 방법은 경제적우로 큰 부당이 되며 공사기간 연장의 한 원인이 된다. 따라서 곡연막장 굴착공법을 개발하여 적용한다면 보다 나은 응력상태를 유지할 수 있어 1회 불진장의 증대 및 분할공법을 피함으로써 공사비절감 및 공사기간 단측에 매우 유리할 것이라 판단된다. In this study, NATM can reduce the loosened ground near the tunnel face more than the other pre-existing tunnelling methods, because of rapid supporting by means of shotcrete and rock bolts. However, this method sometimes can not help for a unstable tunnel face with a unsupported caondition. In order to keep from that dangerous case, some excavation methods such as bench cut and drift advancing method are introduced, despite of high construction cost and period. So, this thesis is intended to introduce the new tunnel face shape, that is concave shaped face, and discusses its effects on the tunnel stabilization.

서울 ${\cdot}$ 경기지역 냉면전문점의 서비스 품질에 대한 중요도 평가

김태형,오유진,이영미,Kim, Tae-Hyoung,Oh, Yu-Jin,Lee, Young-Mee 한국식생활문화학회 2007 韓國食生活文化學會誌 Vol.22 No.1

The purpose of this study was to analyze evaluation variables of service quality of Korean restaurant especially focused on cold noodle restaurants(CNR). The data were analyzed about customer’s expectation of food service quality, service quality was improved by employee’s service in restaurant and employee education in the focus on CNR. The survey was carried out 423 customers and 50 employees in Seoul and Kyunggi province. All statistical data analyses were conducted using the Statistical Package for the Social Science(SPSS version 10.0). The consumer’s evaluation score of service quality were significantly different by consumer’s characteristics. The well planned service at CNR must be developed according to consumer variables such as sex and age group. The evaluation score of service quality were not significantly different by seasonal variation and consumer’s menu selection. The evaluation score of service qualities in CNR were significantly different between customer variables with employees variables. All of the evaluation points of service quality in employees were significantly higher than customers. This result was show that well-trained employees were important factors in consumer satisfaction. Through the employee education program, consumer oriented service mind mort be to developed in employees and employees’ recognition about the importance of service increased the satisfaction of customer using CNR.

정관내 부목을 이용한 정관복원술 : Permanent Silicone Stent의 효용가치

김태형,김세철,Kim, Tae-Hyoung,Kim, Sae-Chul 대한생식의학회 1996 Clinical and Experimental Reproductive Medicine Vol.23 No.1

During a 2-year period microsurgical vasovasostomies using permanent silicone stent(c-shaped stent with 0.6mm slit, 5mm in length, 0.8mm in outer diameter, 0.5mm in inner diameter) were performed in 30 patients for vasectomy revesal. The stent-assisted vasovasostomy(SVV) was intended to decrease the technical demand, the time requirement and the occurrence of reobstruction due to postoperative stricture. The effectiveness of the permanent silicone stent for vasovasostomy was compared with that of microsurgical two-layered vasovasostomy(VV). Sperms were present in all the ejaculates of the 25 men on semen analysis 1-2 months after SVV. Pregnancy occurred in 10 of 22 couples(45.5%) during 2-24 months of follow-up and it took 4-10 months(average 7.2 months) to get pregnant. Average operation time for the VV was 150 minutes and that for the SVV 125 minutes. Among 12 men who had sperms in the ejaculates 1-2 months after SVV, 4 revealed azoospermia 3-17 months postoperatively. Among the 4 patients with postoperative azoospermia, 2 underwent reoperation. On histopathologic examination, previously anastomsed sites showed obliterated lumen of the stent and strictures of vas proximal and/or distal to the stents due to granulation tissues. In conclusion, the SVV was not more efficacious in terms of patency and pregnancy rate than the VV.

낙동강 하구 화전지구 연약지반에 작용하는 피압수압 측정사례

김태형,유재명,이명재,배기현,정두석,Kim, Tae-Hyoung,Yu, Jae-Myung,Lee, Myung-Jae,Bae, Ki-Hyun,Jeong, Doo-Suk (사)한국토질및기초기술사회 2006 기술발표회 Vol.2006 No.-

Artesian Pressure exists in Hwa Jeon Project Site of Nakdong Delta Area. Maxium value of the pressure ranges between 06 tonf/m2 and 1 3 tonf/m2 in the design site. This paper presents a design case study considering the Artesian Pressure to calculate the consolidation settlement of the deep marine clay.

용매증발법을 이용한 Poly-L-Lactic Acid (PLLA) 마이크로스피어 제조

김태형,송기창,Kim, Tae Hyoung,Song, Ki Chang 한국화학공학회 2018 Korean Chemical Engineering Research(HWAHAK KONGHA Vol.56 No.4

Poly-L-lactic acid (PLLA)를 출발물질로 하여 용매증발법에 의해 마이크로스피어를 제조하고, 제조 변수가 형성된 마이크로스피어의 형상 및 평균 입경에 미치는 영향을 살펴보았다. PVA 수용액의 농도가 1~5 wt%로 증가함에 따라 평균입경이 $370{\sim}160{\mu}m$으로 감소하다가 7 wt%에서다시 $240{\mu}m$으로 증가하였다. 그리고 PVA의첨가부피가 10~50 mL로 증가함에 따라 평균 입경은 $370{\sim}220{\mu}m$으로 감소하였다. 또한 교반속도가 500~1,500 rpm으로 증가함에 따라 평균 입경은 $370{\sim}110{\mu}m$으로 감소하였다. 유기용매로써 dichloromethane과 chloroform을 각각 사용한 경우 평균 입경은 큰 차이를 보이지 않았으며, dichloromethane을 사용한 경우 표면에서 공극이 확인되었으나 chloroform을 사용한 경우 매끈한 형상의 구형입자가 얻어졌다. Microspheres were prepared by solvent-evaporation method with Poly-L-lactic acid (PLLA) as a starting material, and the effects of preparation variables on microsphere shape and average particle size were investigated. As the concentration of PVA solution increased from 1 to 5 wt%, the average particle size decreased from $370{\mu}m$ to $160{\mu}m$ and then increased to $240{\mu}m$ at 7 wt%. On the other hand, As the addition volume of PVA solution increased from 10 mL to 50 mL, the average particle size decreased from $370{\mu}m$ to $220{\mu}m$. Also, as the stirring speed increased from 500 rpm to 1,500 rpm, the average particle size decreased from $370{\mu}m$ to $110{\mu}m$. When dichloromethane and chloroform were used as organic solvents, respectively, the average particle size did not show any significant difference. However, when dichloromethane was used, voids were observed on the particle surface, but when chloroform was used, smooth spherical particles were obtained.

콘크리트 생산에 의한 CO₂ 배출량 평가 시스템 개발에 관한 연구

김태형,태성호,Kim, Tae-Hyoung,Tae, Sung-Ho 한국콘크리트학회 2010 콘크리트학회논문집 Vol.22 No.6

전 세계적으로 지구 온난화의 주요원인인 $CO_2$ 발생에 대한 규제가 강화되고 있다. 반 환경산업으로 인식되는 건설 산업의 주요자재로서 다량의 $CO_2$를 배출하는 콘크리트는 생산과정에서 발생된 $CO_2$ 배출량 감소에 대한 필요성이 인식되었다. 이 논문에서는 콘크리트를 기초로 하여 자재생산, 운송, 제조단계에서 발생하는 $CO_2$ 배출량을 평가하기 위한 시스템을 구축하고, $CO_2$ 배출량을 효율적으로 저감하고 평가하기 위한 프로그램을 개발 하였다. 평가결과, 대부분의 $CO_2$ 배출량은 자재생산단계에서 발생했으며, 자재, 운송, 제조단계에서 배출된 $CO_2$ 배출량에 대하여 정량적으로 평가하였다. 더욱이, $CO_2$ 배출량을 저감하기 위하여 각 단계별로 친환경 기술을 적용하여 평가가 가능한 이 평가시스템은 콘크리트 생산에 따른 $CO_2$ 배출량을 정량적으로 평가하기 위한 시스템으로 제안할 수 있으며, 국내 레미콘생산업체는 $CO_2$ 배출량 평가를 하기 위해 이 시스템을 사용할 수 있다. The main reason of the earth global warming is $CO_2$ and the regulation about it in the whole world has been reinforced to reduce $CO_2$ emission. It is needed that we should reduce it in the process at the production of concrete generated much of $CO_2$ emission as the primary material of construction industry recognized unfriendly environment industry. Based on a concrete, this study was constructed the system to evaluate $CO_2$ emission generated in the stage of material production, transportation, manufacture and developed the program to reduce and evaluate it efficiently. As a result, most of $CO_2$ emission is generated in the stage of material and it is quantitatively evaluated $CO_2$ emission generated in the stage of materials, transportation and manufacture. Moreover, the evaluation system of the volume of $CO_2$ emission which has the friendly environment technology about reduction of $CO_2$ emission at each stage is suggested for quantitatively evaluation $CO_2$ emission generated in the process at the production of concrete and remicon production company could use it to evaluation $CO_2$ emission.

펌핑 구조에 따른 1 kW급 협대역 편광 유지 광섬유 레이저의 출력 특성 연구

김태형,정성묵,김기혁,이성헌,양환석,Kim, Tae Hyoung,Jeong, Seong Mook,Kim, Ki Hyuck,Lee, Sung Hun,Yang, Hwan Seok 한국광학회 2021 한국광학회지 Vol.32 No.4

본 논문에서는 주 증폭기가 양방향 펌핑 방식인 MOPA (master oscillator power amplifier) 협대역 고출력 광섬유 레이저를 제작하였으며, 제작된 레이저의 출력 특성을 연구하였다. 이터븀이 도핑된 코어 25 ㎛, 클래드 400 ㎛ 편광 유지 광섬유를 사용하여 주 증폭부를 제작하였으며, 신호 광원은 PRBS (pseudo-random binary sequence) 신호에 의해 위상 변조된 3 GHz, 10 GHz의 선폭을 갖는 광원을 사용하였다. 3 GHz의 선폭을 가진 신호 광원을 이용하여 순방향과 역방향 펌프 비율을 조절하며 SBS (stimulated Brillouin scattering) 특성을 분석하였다. 10 GHz의 선폭을 가진 신호 광원을 이용하여 주 증폭기의 펌핑 비율에 따른 TMI 특성을 분석하였다. 순방향 및 역방향 펌프 비율을 1.6:1로 입사시켰을 때 주 증폭기의 출력을 1 kW까지 증폭하였으며, 기울기 효율과 빔 품질(M²)은 각각 80%, 1.36으로 측정되었다. This paper presents a study of laser output characteristics. We fabricated a MOPA (master oscillator power amplifier)-type high-power, narrowbandwidth fiber laser with a bidirectional pumping configuration in its main amplifier. As signal beams, light sources with bandwidths of 3 GHz and 10 GHz-phase-modulated through a PRBS (pseudo-random binary sequence)-were used interchangeably. Furthermore, the characteristics of the SBS (stimulated Brillouin scattering) were analyzed using a signal beam with 3 GHz bandwidth, by adjusting the forward to backward pumppower ratio. Moreover, the characteristics of the transverse mode instability were analyzed by adjusting the forward to backward pump-power ratio, using a signal beam with 10-GHz bandwidth. Finally, the output power from 10 GHz bandwidth was amplified to more than 1 kW using a forward to backward pump-power ratio of 1.6. The beam quality M² was measured to be approximately 1.36, and the optical-to-optical efficiency was 80% at maximum output power.