Welcome the Challenges and Imaging the Sky Town

Cheng, Jiang Huan Council on Tall Building and Urban Habitat Korea 2017 International journal of high-rise buildings Vol.6 No.3

Safety, livability, and efficiency are the three prominent problems of tall buildings, which are also the severe challenges to designers. We proposed the idea of building the sky town to solve these problems, which can be summarized in two sentences, one is tall building multi-storised, and another one is vertical facilities municipal-infrastructurised. The tall building can be horizontally cut into several multi-storey buildings by some large platforms. The platform extends a certain width to block the fire from spreading. Tall buildings are connected together as a group. One of them is a traffic core, which is used for vertical transportation and MEP. It connects to traffic center such as metro, while most of the other tall buildings' cores can be very much released, so as to achieve maximum efficiency of floor usable area and to give good traffic organization. By combining traffic core, platforms, and multi-storey buildings' inner traffic, a transportation network is formed. Finally, we refer to the design of Raffles City Chongqing to make a sketch of sky town.

Upregulation and biological function of transmembrane protein 119 in osteosarcoma

Zhen-Huan Jiang,Jun Peng,Hui-Lin Yang,Xing-Li Fu,Jin-Zhi Wang,Lei Liu,Jian-Nong Jiang,Yong-Fei Tan,Zhi-Jun Ge 생화학분자생물학회 2017 Experimental and molecular medicine Vol.49 No.-

Osteosarcoma is suggested to be caused by genetic and molecular alterations that disrupt osteoblast differentiation. Recent studies have reported that transmembrane protein 119 (TMEM119) contributes to osteoblast differentiation and bone development. However, the level of TMEM119 expression and its roles in osteosarcoma have not yet been elucidated. In the present study, TMEM119 mRNA and protein expression was found to be up-regulated in osteosarcoma compared with normal bone cyst tissues. The level of TMEM119 protein expression was strongly associated with tumor size, clinical stage, distant metastasis and overall survival time. Moreover, gene set enrichment analysis (GSEA) of the Gene Expression Omnibus (GEO) GSE42352 dataset revealed TMEM119 expression in osteosarcoma tissues to be positively correlated with cell cycle, apoptosis, metastasis and TGF-β signaling. We then knocked down TMEM119 expression in U2OS and MG63 cells using small interfering RNA, which revealed that downregulation of TMEM119 could inhibit the proliferation of osteosarcoma cells by inducing cell cycle arrest in G0/G1 phase and apoptosis. We also found that TMEM119 knockdown significantly inhibited cell migration and invasion, and decreased the expression of TGF-β pathway-related factors (BMP2, BMP7 and TGF-β). TGF-β application rescued the inhibitory effects of TMEM119 knockdown on osteosarcoma cell migration and invasion. Further in vitro experiments with a TGF-β inhibitor (SB431542) or BMP inhibitor (dorsomorphin) suggested that TMEM119 significantly promotes cell migration and invasion, partly through TGF-β/BMP signaling. In conclusion, our data support the notion that TMEM119 contributes to the proliferation, migration and invasion of osteosarcoma cells, and functions as an oncogene in osteosarcoma.

Study on adaptive concentric performance of floating self-concentric seals

Huan Zhao,Jindao Guo,Dan Sun,Min Zhou,Jinyu Jiang,Ping Wang 대한기계학회 2022 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.36 No.5

In present study, solution models for CTPS, CCPS, and LS were established to study radial pressure distribution of the seals and to analyze the effects of inlet/outlet pressure ratios and eccentricity ratios on floating concentric force. A floating self-concentric seal experiment apparatus was designed to study the effects of inlet/outlet pressure ratios and eccentricity ratios on response time and moving track of CTPS, CCPS and LS. The results show that CTPS has a good adaptive concentric performance, which is more suitable as a floating seal ring. Under different inlet/outlet pressure ratios and eccentricity ratios, CTPS always move towards concentric direction, and thereafter stabilizes at equilibrium location with a low eccentricity ratio, which is contributed to the greater floating concentric force counteracting friction force between the ball and plate. With the increase of inlet/outlet pressure ratio and eccentricity ratio, it takes a shorter floating response time to reach the equilibrium location.

A Study of the Effect of Tungsten Oxide on W, WC Powder and Alloy Properties

Jiang Cijin,Shen Paul,Wang Huan 한국분말야금학회 2006 한국분말야금학회 학술대회논문집 Vol.2006 No.1

This is about the effects deoxidization, carbonization and alloying preparation on fine grain W, WC, and grade YG8 powder reduced by "yellow tungsten oxide" and "blue tungsten oxide". The result indicates that yellow tungsten has single composition and blue tungsten oxide has complex composition. With this feature, yellow tungsten oxide got better uniformity and concentration distribution on fine particle size W and WC powder than blue tungsten oxide's. The grade alloy YG8 that made of this W or WC powder has uniform alloy construction, concentrated WC grain distribution and better alloy properties.

Study on Fiber Cutting Performance of Isometric Straight Bar Plate with Different Bar Angle

Huan Liu,Jixian Dong,Xiya Guo,Chong Luo,Xiaohui Tian,Xiaojun Jiang,Sha Wang,Ruifan Yang,Chuanwu Duan,Bo Wang,Kai Qi 한국펄프·종이공학회 2019 펄프.종이기술 Vol.51 No.5

The refining plate is a direct-acting component of refiners in pulping, and the bar profile of it have a major impact on fiber cutting, which affects the paper forming and strength of the formed paper. In this paper, the fiber average length, the fiber length distribution, the original fiber cutting rate and adjacent fiber cutting rate of samples collected in different refining time are used to analyze the fiber cutting mechanism of the isometric straight bar refining plates with different bar angles. The results show that the fiber cutting performance of plates gradually decreases and the limit fiber cutting length of the plate increases with the increase of the bar angle which is opposite to the conclusion predicted by specific edge load (SEL). However, the fiber cutting action of plates is gradually weakened until the average fiber length is reduced to the limit cutting length of plates. Meanwhile, the cutting mechanism of the straight bar plates with different bar angles is different. The larger bar angle of plate, the lower fiber cutting rate and the adjacent cutting rate of which is basically kept constant during refining, while the adjacent cutting rate of smaller bar angle plate on fibers gradually decreases with refining and finally remains constant. The study on the cutting performance of different bar angle plates has positive significance for the selection and design of refining plates for different pulping process.

Effect of TPU on β-phase formation of PVDF

HUAN LI,Tridib K. Sinha,Hao Gong,Yufei Jiang,Youngjoon Ahn,김진국 한국고분자학회 2018 한국고분자학회 학술대회 연구논문 초록집 Vol.43 No.1

Synthetic Aperture Technique and Its Application in Medical Ultrasonic Imaging

Jiang Hui,Hou Chao-huan 한국소음진동공학회 1994 한국소음진동공학회 국제학술대회논문집 Vol.1994 No.3

Dehydration of Methanol to Dimethyl Ether over ZSM-5 Zeolite

Jiang, Shan,Hwang, Jin-Soo,Jin, Tai-Huan,Cai, Tianxi,Cho, Wonihl,Baek, Young-Soon,Park, Sang-Eon Korean Chemical Society 2004 Bulletin of the Korean Chemical Society Vol.25 No.2

Methanol dehydration to dimethyl ether (DME) has been investigated over ZSM-5 zeolites and compared with that of ${\gamma}-Al_2O_3$. Although the catalytic activity was decreased with an increase in silica/alumina ratio, the DME selectivity increased. H-ZSM-5 and NaH-ZSM-5 zeolites were more active for conversion of methanol to DME than ${\gamma}-Al_2O_3$. $Na^+$ ion-exchanged H-ZSM-5 (NaH-ZSM-5) shows higher DME selectivity than H-ZSM-5 due to the selective removal of strong acid sites.

Breathing-based Continuous Non-intrusive User Verification Leveraging Commodity WiFi

Huan Dai,Jingjing Jiang,Jiaju Ma,He Huang,Hongbo Liu 한국통신학회 2022 Journal of communications and networks Vol.24 No.2

This paper opens up a new pathway of the utilityof breathing pattern for user verification. We demonstrate thatit is possible to capture people’s breathing pattern leveragingcommodity WiFi devices. While prior solutions for biometricsbaseduser recognition usually require dedicated devices (e.g.,video cameras or IR sensors), this paper introduces the firstgeneral, low-cost breathing-based user verification system usingcommodity WiFi devices. The proposed system is based onthe fact that the breathing pattern always keeps consistentfor the same user but distinct among different people. Ourinnovative method successfully extracts the breathing patternof different people based on channel state information of WiFisignal to facilitate user verification. The prototype study usingtwo commodity WiFi devices can differentiate people with anaverage verification accuracy over 90%, suggesting that ourbreathing-based user verification system using commerical offthe-shelf (COTS) WiFi is promising to be one of the most criticalmethods in biometrics.

Refining Characteristics of Hardwood Pulp Using Straight- and Curved-bar Plates: A Time Series Study

Huan Liu,Jixian Dong,Xiaojun Jiang,Chong Luo,Xiaohui Tian,Ruifang Yang,Litao Zhang,Bo Wang,Yan Yan 한국펄프·종이공학회 2019 펄프.종이기술 Vol.51 No.5

There are obvious differences in the refining characteristics of plates with straight bars compared to curved bar plates having the same bar parameters during refining. The objective of this research is to explore the difference in the refining characteristics of the straight bar and curved bar plates on experimental and theoretical studies. The bar angle of the curved bar plate is defined, and the two plates are used in the refining of bleached sulphate eucalyptus pulp (BSEP). Samples at different refining times were collected, and the properties of the fibers, pulp, and paper were detected and analyzed. It was found that the curved bar and straight bar plates have a similar influence on the pulp SR freeness. However, the curved bar plate effectively retained the fiber length, which means that its fiber cutting effect is weaker than that of the straight bar plate. Meanwhile, the fiber external fibrillation of the samples refined by the curved bar plate was better than that of the samples refined by the straight bar, which showed a higher tensile and tear index of the formed paper. Through the theoretical analysis of refining intensity via characterization of the parameter bar edge length (BEL), the specific edge load (SEL) of the curved bar plate was lower, and the refining characteristics predicted by the refining intensity were similar to the results from the experiments conducted in this paper.