http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
박근웅,한유희,이상윤 ( K . W . Park,Y . H . Han,S . Y . Lee ) 한국열처리공학회 1996 熱處理工學會誌 Vol.9 No.4
This study has been performed to investigate into some effects of power density and traverse speed of laser beam on optical microstructure, hardness and wear characteristics of gray cast iron treated by laser surface hardening technique. Optical micrograph has shown that large martensite and a small amount of retained austenite appear in outermost surface layer with fine martensite in inside hardened zone. Hardness measurements have revealed that the range of maximun hardness value is Hv=650±15 and as the power density increases and the traverse speed decreses, the depth of hardened zone increases due to as increase in input power density. Wear test has exhibited that wear rasistance of laser surface hardened specimen is superier compared to that of untreated specimen under the condition of same load at a given sliding distance, showing that absorption results of an wxidized substance due to a heavy abrasion appear in untreated specimen. The amount of weight loss of laser surface hardened specimen with respect to sliding distance at a given load decreses with increasing traverse speed at a given power density and with increasing power density at a given traverse speed.
서정,한유희,김정오,이영신,Suh, J.,Han, Y.H.,Kim, J.O.,Lee, Y.S. 대한용접접합학회 1996 대한용접·접합학회지 Vol.14 No.1
The maximum butt-joint gap size in $CO_2$ laser beam welding of SAPH steel plates with different thicknesses and its bending formability were studied. In the range of the gap size$\geq$0.1mm, the optimal butt welding speed was faster than that of no gap (air gap) condition. This behaviour was independent on the difference of thickness at any combination. Also, the allowable gap size in steel plates with different thicknesses was larger than with same thicknesses. In the range of $T/T_0$(bead shape) $\geq$ 0.8, good bending formability was obtained at any combination of thickness. The formability was improved by reducing the hardness in weld bead using pre-heating process. Finally, FEM result of the laser beam welded underframe with different thicknesses was compared to that of the conventional spot welded underframe.
아연도금강판의 CW $CO_2$ 레이저 용접 및 성형성
서정,한유희,윤충섭,방세윤,Suh, J.,Han, Y.H.,Yoon, C.S.,Bang, S.Y. 대한용접접합학회 1995 대한용접·접합학회지 Vol.13 No.1
Continuous wave C $O_{2}$ laser beam welding and formability of zinc coated steel plates were investigated. First, the optimal welding condition could be obtained in lap configuration by using the data for heat input, gap size and fracture behaviour. The gap size for fully-penetrated bead could be predicted by the gap model by Akhter et al. AIso, it was found that the joining efficiency was constant. Secondly, the butt welding of dissimilar materials (zinc coated steel plate and cold rolled steel plate) with different thicknesses was investigated. In the thickness range of 0.8-2.0 mm, the maximum welding speed of 10m/min was obtained. In the butt welding of two plates with thickness 2.0 mm and l.6mm, the maximum, welding speed of 6m/min was obtained, Finally. the forming results of butt-welded plates showed that the joining design was important to apply the laser welded blank in the automotive production.
백동기,한유희,김기대,정철,Paek, T.K.,Han, Y.H.,Kim, K.D.,Jung, C. 대한용접접합학회 1991 대한용접·접합학회지 Vol.9 No.2
1. 16bit 개인용 컴퓨터인 IBM-PC/AT수준에서 레이저 가공을 위한 임의의 도형을 입력하여 DXF File로 출력하고, External명령인 AutoCAM을 추가하여 AutoCAM의 실행이 가능하였으며 AutoCAM의 종료후에는 다시 AutoCAD로 작업이 가능하다. 2. 개발한 AutoCAM은 AutoCAD Ver 2.6i로부터 Release 10까지의 DXF File을 읽어 Graphic 출력이 가능하다. 3. 가공 경로를 NC프로그램이 임의로 선정가능하면서, 가장 능률적인 가공작업이 수행될 수 있 도록 연속 또는 최인접 도형요소를 자동 선정하고 이의 조건에 따른 Auto Mode의 NC프로그램 생성이 가능하다. 4. 생성된 NC프로그램을 레이저 가공기에 전송하여 가공실험을 실시한 결과, 생성된 NC 프로 그램은 거의 수정하지 않아도 작동이 가능한 정도의 만족할 만한 결과를 얻었으므로 실용화에 큰 문제가 없는 것으로 사료된다. 이상과 같이 레이저 가공을 위한 CAD/CAM시스템은 초심자등의 이용상의 편리를 위하여 대화식으로 하였으며 사용된 언어도 Quick BASIC으로 자체 개발하 였으므로 앞으로 이 분야의 연구 및 실용화를 위한 기초자료로 활용될 수 있을 것으로 사료된다.
Co2레이저 비임을 이용한 표면경화 처리중 형성된 AISI 4140의 잔류응력에 관한 연구
박근웅,이준범,한유희,이상윤 ( K . W . Park,J . B . Lee,Y . H . Han,S . Y . Lee ) 한국열처리공학회 1996 熱處理工學會誌 Vol.9 No.4
This study has been performed to investigate into some effects of power density and traverse speed of laser beam on the microstructure, hardness and residual stress of AISI 4140 treated by laser surface hardening technique. Optical micrograph has shown that large martensite and a small amount of retained austenite in outermost surface layer and fine lath martensite in inner surface hardened layer are formed under the condition of a given power density and traverse speed. Hardness measurements have revealed that as the power density increases at a given 2.0m/min of the traverse speed, the maximum hardness values of outermost surface hardened layer is increased from Hv=635 to Hv=670. X-ray analysis for residual stress has exhibited that low compressive residual stress values are obtained in center point of the cress section of surface hardened layer with in mid point between the edge and the center point, about 1.5㎜ from the center point, due simply to a difference in self-quenching rate. It has been shown that the higher the power density at a given traverse speed and the olwer the traverse speed at a given power density, the more the compressive residual stress values are increased due to an increase in the input heat of laser beam.