http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
참치 뼈를 이용한 Hydroxyapatite 세라믹 복합체의 합성 및 생체 친화성 ( 제2보 ) - 습식법에 의한 Hydroxyapatite 소결체의 특성 -
김세권,최진삼,이창국,변희국,전유진,이응호 ( Se Kwon Kim,Jin Sam Choi,Chang Kook Lee,Hee Guk Byun,You Jin Jeon,Eung Ho Lee ) 한국공업화학회 1997 공업화학 Vol.8 No.6
참치 뼈로부터 추출한 hydroxyapatite[Ca_10(PO₄)_6(OH)₂]를 습식법으로 분쇄한 후 여러 온도로 고상반응시킨 세라믹 소결체의 특성을 고찰하였다. Hydmxyapatite소결체의 밀도는 1350℃에서 약 2.93g/cm³으로서 이론치의 3.21g/cm³과 유사하였다. 1300℃ 이하의 소결온도에서는 hydroxyapatite가 결정상으로 나타났으며, 온도가 증가할 수록 hydroxyapatite의 분해에 따른 whitlockite[Ca₃(PO₄)₂]의 결정상이 관찰되었다. 소결체의 미세구조는 발달된 입계들 사이에 폐기공들이 분포하였다. 1350℃의 소결시편 평균강도는 58 MPa로 나타나 관절연골(articular cartilage)의 최대강도인 40 MPa보다 우수한 것으로 나타났다. The properties of ceramics by solid-state reaction with hydroxyapatite[Ca_10(PO₄)_6(OH)₂] which was isolated from tuna bone by wet milling process were investigated. The bulk density 2.93g/cm³ at 1350℃ was close to the calculated density 3.21g/cm³. On X-ray measurements, the major phases were identified as hydroxyapatite at below 1300℃, but the whitlockite [Ca₃(PO₄)₂] phases were appeared due to a decomposition of hydroxyapatite with temperature. The microstructures of sintering specimens were shown as small closed pores between grain boundaries. The mean bending strength of the sintered hydroxyapatite by solid-state reaction is about 58 MPa and this value is higher than that of the articular cartilage maximum strength, 40 MPa.
Plastein반응을 이용한 정어리 단백질의 기능성 개선에 관한 연구 - 1. 정어리 분말단백질의 pepsin가수분해물을 이용한 plastein의 합성조건
김세권(Se-Kwon Kim),곽동채(Dong-Chae Kwak),조덕제(Duck-Jae Cho),이응호(Eung-Ho Lee) 한국식품영양과학회 1988 한국식품영양과학회지 Vol.17 No.3
어육 단백질의 기능성을 개선하기 위해 정어리 분말단백질의 pepsin가수분해물을 이용하여 plastein을 합성하기 위한 반응조건을 검토하였다.<br/> plastein합성반응 최적조건으로서는 pepsin, α-chymotrypsin, protease(Aspergillus saitoi) 및 papain의 경우 pH는 각각 4,7,5 및 6, 기질농도는 pepsin과 α-chymotrypsin의 경우 40%였으나 protease와 papain은 50%였다. 온도는 4종의 효소 모두가 50℃였다. 기질의 가수분해도가 60%이상에서 plastin합성반응이 이루어졌으며, 가수분해도가 78.4% 이상이 었을 때 plastein 생성량은 높았다. In order to develop a new type of food source for the effective utilization of fish protein, plastein reaction was applied to improve the functional properties of sardine protein.<br/> Conditions necessary for optimal plastein productivity from sardine protein using pepsin, α-chymotrypsin, protease(from Aspergillus saitoi) and papain were established.<br/> Sardine protein concentrate was hydrolyzed with pepsin yielding an approximate degree of hydrolysis of 78.4%. Enzyme induced plastein was optimized at: pH 4 for pepsin, pH 7 for α-chymotrypsin, pH 5 for protease and pH 6 for papain: Substrate concentrate 40% for pepsin and α-chymotrypsin, 50% for protease and papain: the time of incubation, 24hr: enzyme/substrate ratio, 1:100(w/v) incubation temperature, 50℃.
LRF 센서를 이용한 글로벌 맵 기반의 적응형 이동 장애물 회피 알고리즘 개발
오세권(Se-Kwon Oh),이유상(You-Sang Lee),이대현(Dae-Hyun Lee),김영성(Young-Sung Kim) 한국정보전자통신기술학회 2020 한국정보전자통신기술학회논문지 Vol.13 No.5
본 논문에서는 고정된 장애물이 포함된 글로벌 맵 환경에서 LRF 센서만을 가진 자율이동 로봇이 이동장애물을 회피하기 위한 알고리즘을 제안한다. 우선 이동장애물을 회피하기 위해 LRF 거리 센서 데이터와 글로벌 맵을 이용하여 이동장애물을 추출한다. 추출된 이동장애물과 자율이동 로봇의 상대적인 벡터 성분의 합을 이용해 타원 형태의 안전반경을 생성한다. 생성된 안전반경을 고려하여 자율이동 로봇이 이동장애물을 회피하고 목적지에 도착할 수 있도록 한다. 제안된 알고리즘을 검증하기 위해 정량적인 분석 방법을 사용하여 기존 알고리즘과 비교하고 분석한다. 분석 방법은 이동장애물이 없을 때를 기준으로 제안된 알고리즘과 기존의 알고리즘의 경로의 길이와 주행 시간을 비교한다. 제안된 알고리즘은 이동장애물의 상대적 속도와 방향을 고려하여 회피할 수 있어서 경로와 주행 시간 모두 기존의 알고리즘보다 높은 성능을 보인다. In this paper, the autonomous mobile robot whit only LRF sensors proposes an algorithm for avoiding moving obstacles in an environment where a global map containing fixed obstacles. First of all, in oder to avoid moving obstacles, moving obstacles are extracted using LRF distance sensor data and a global map. An ellipse-shaped safety radius is created using the sum of relative vector components between the extracted moving obstacles and of the autonomuos mobile robot. Considering the created safety radius, the autonomous mobile robot can avoid moving obstacles and reach the destination. To verify the proposed algorithm, use quantitative analysis methods to compare and analyze with existing algorithms. The analysis method compares the length and run time of the proposed algorithm with the length of the path of the existing algorithm based on the absence of a moving obstacle. The proposed algorithm can be avoided by taking into account the relative speed and direction of the moving obstacle, so both the route and the driving time show higher performance than the existing algorithm.
소결금속 윅과 메탄올을 사용하는 Capillary pumped loop의 작동특성
이세권(Se Kwon Lee),정의국(Eui Guk Jung),부준홍(Joon Hong Boo) 대한기계학회 2009 대한기계학회 춘추학술대회 Vol.2009 No.5
A capillary pumped loop(CPL) having a cylindrical evaporator was investigated. Inner diameter of the evaporator was 12 ㎜. The bottom of the evaporator was flat plate having dimension 35 by 35 ㎜ for a practical application to electronic component cooling. The lengths of the vapor and liquid transport lines were 300 ㎜ and 400 ㎜, respectively. The capillary structure was a sintered metal wick made of stainless steel, and the working fluid was methanol. The thermal load range was up to 35 W at the condenser above evaporation position.
Z-Segmentation 알고리즘을 이용한 발사체의 배선 점검 방법
오세권 ( Se-kwon Oh ),이대현 ( Dae-hyun Lee ),김영성 ( Yung-sung Kim ),안종흠 ( Jong-heum An ) 한국항행학회 2021 韓國航行學會論文誌 Vol.25 No.5
항공 우주 산업의 발전으로 발사체의 연구가 많아지고 있다. 더불어 많은 시험이 진행하고 있고 그에 따라 많은 실패도 발생한다. 발사체는 다른 전자장비보다 위험성이 높기 때문에 실패를 최소화할 수 있어야 한다. 따라서 발사체에 전원을 공급하기 전에 배선을 검증할 필요가 있다. 이에 따라 저항 측정을 통해 배선 상태를 검증하였다. 하지만 이전의 저항측정 방식의 배선 점검은 발사체 회로의 커패시터, 인덕터등의 소자들 때문에 정확한 측정을 할 수 없다. 본 논문에서는 TDR 미터를 이용하여 케이블 및 발사체의 연결 상태에서 임피던스를 측정한다. 측정한 정상상태의 임피던스의 기준 값을 설정하기 위해 Z-Segmentation 알고리즘을 사용한다. Z-Segmentation 알고리즘은 우선 임피던스 파형의 피크 값들을 칼만 필터를 이용하여 찾고 찾은 피크 값을 Segmentation을 통해 최종 impedance peak segment를 얻는다. 이런 방법으로 배선의 정상 상태에 대한 기준 값으로 설정하고 이를 기준으로 배선 상태를 판정한다. development of the aerospace industry is increasing the research of projectiles. In addition, many tests are under way and many failures occur accordingly. Projectiles should be able to minimize failures because they are more dangerous than other electronic equipment. Therefore, it is necessary to verify wiring before powering the projectile. Accordingly, the wiring status was verified by resistance measurements. However, the wiring test of the previous resistance measurement method cannot be accurately measured due to devices such as capacitors and inductors in the projectile circuit. In this paper, impedance is measured in the connection state of cables and projectiles using a TDR meter. The Z-Segmentation algorithm is used to set the reference value for the measured steady state impedance. The Z-Segmentation algorithm first finds the peak values of the impedance waveform using a Kalman filter and obtains the final impedance peak segment through segmentation. In this way, the wiring status is determined based on the reference value for the normal state of the wiring.
이세권(Se Kwon Lee),곽호협(Ho Hyup Kwak),부준홍(Joon Hong Boo),김종규(Jong Kyu Kim),강용혁(Yong Hyuk Kang) 대한기계학회 2009 대한기계학회 춘추학술대회 Vol.2009 No.11
An experimental investigation was conducted on a heat pipe for application in a thermal storage system consisted of a phase-change material (PCM) at around 340℃. The working fluid was Dowtherm-A and the screen mesh wick as well as the container was made of stainless steel. Since the PCM should be located in the middle section of the heat pipe configured vertically, and only one of the two extruded ends of the heat pipe should function, either as an evaporator or a condenser, during the heat charge and dissipation mode, the initial fluid charge should be higher than the evaporator length located at the bottom of PCM. The total length and the outer diameter of the heat pipe were 1 m, and 25.4 ㎜, respectively. The thermal performance of the heat pipe was presented in terms of the thermal resistance, the heat transfer coefficient, and the effective thermal conductivities as functions of operating temperature and heat flux.
박세권(Se-Kwon Park),이승록(Seung-Rok Lee) 국립공원연구원 2013 국립공원연구지 Vol.4 No.1
2008년 4월부터 2012년 10월까지 속리산국립공원 7개 조사지점에 담수어류상을 조사하였다. 채집된 어류는 5목 8과 24종 8,880개체로 확인되었다. 우점종은 참갈겨니 Zacco koreanus(73.0%)이었다. 한국고유종은 묵납자루 Acheilognathus signifer, 줄납자루 Acheilognathus yamatsutae, 가는돌고기 Pseudopungtungia tenuicorpa, 쉬리 Coreoleuciscus splendidus, 참중고기 Sarcocheilichthys variegatus wakiyae, 돌마자 Microphysogobio yaluensis, 배가사리 Microphysogobio longidorsalis, 참종개 Iksookimia koreensis, 미유기 Silurus microdorsalis, 자가사리 Liobagrus mediadiposalis, 퉁가리 Liobagrus andersoni, 둑중개 Cottus koreanus, 꺽지 Coreoperca herzi, 얼록동사리 Odontobutis interrupta 등 14종으로 확인되었다. 법정보호종은 환경부지정 멸종위기야생동·식물 II급인 묵납자루 Acheilognathus signifer와 가는돌고기 Pseudopungtungia tenuicorpa 2종이 확인되었다. 전체 연구기간 중 가장 다양한 종이 출현한 시기는 2009년(17종)이었고 2008년에는 16종이 확인되었다. The fauna of freshwater fish were investigated from Aprial, 2008 to October, 2012 at seven station in Songnisan National Park. During the surveyed preriod, Collected fishes were 8,880 individuals and were identified to 24 species 8 genera belonging to 5 orders. Dominant species was Zacco koreanus (73.0%). The endemic species of Korea were 14 species: Acheilognathus signifer, Acheilognathus yamatsutae, Pseudopungtungia tenuicorpa, Coreoleuciscus splendidus, Sarcocheilichthys variegatus wakiyae, Microphysogobio yaluensis, Microphysogobio longidorsalis, Iksookimia koreensis, Silurus microdorsalis, Liobagrus mediadiposalis, Liobagrus andersoni, Cottus koreanus, Coreoperca herzi, Odontobutis interrupta. Endangered species (Level II) by the Ministry of Environment Were 2 species: Acheilognathus signifer, Pseudopungtungia tenuicorpa. The period when the most various species appeared during the total research period was 2009 (17 species), and 16 species were confirmed in 2008.