http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
송성재,장호명,Song, S.J.,Chang, H.M. 대한설비공학회 1997 설비공학 논문집 Vol.9 No.4
Analysis is performed to determine the optimal lengths or cross-sectional areas of refrigerator-cooled current leads that can be applied to the conduction-cooled superconducting systems. The binary current lead is composed of the series combination of a normal metal at the upper(warm) part and a high $T_c$ superconductor(HTS) at the lower(cold) part. The heat conduction toward the cold end of HTS part constitutes a major refrigeration load. In addition, the joint between the parts should be cooled by a refrigerator in order to reduce the load at the low end and maintain the HTS part in a superconducting state. The sum of the work inputs required for the two refrigeration loads needs to be minimized for an optimal operation. In this design, three simple models that depict the refrigeration performance as functions of cooling temperature are developed based on some of the existing refrigerators. By solving one-dimensional conduction equation that take into account the temperature-dependent properties of the materials, the refrigeration works are numerically calculated for various values of the joint temperature and the sizes of two parts. The results show that for given size of HTS, there exist the optimal values for the joint temperature and the size of the normal metal. It is also found that the refrigeration work decreases as the length of HTS increases and that the optimal size of normal metal is quite independent of the size of HTS. For a given length of HTS, there is an optimal cross-sectional area and it increases as the length increases. The dependence of the optimal sizes on the refrigerator models employed are presented for 1kA leads.
송성재(S. J. Song) 한국재활복지공학회 2013 재활복지공학회논문지 Vol.7 No.1
수동 휠체어의 추진은 추진 동작의 낮은 효율로 인하여 사용자의 상지 관절에 고통과 부상까지 유발할 수 있다. 이에 따라 수동 휠체어 추진 중에 발생하는 상지 관절의 운동역학적 해석이 필요하다. 본 연구에서는 수동 휠체어 추진 중 상지 관절에 작용하는 토크를 구할 수 있는 2차원 역동역학 모델을 개발하였다. 개발한 모델은 시상면에서 상완, 하완, 손에 해당하는 3개의 체절로 상지를 구성하였고 몸통으로부터 3개의 체절을 회전조인트로 연결한 개방연쇄구조를 갖는다. 역동역학 해는 뉴턴-오일러 방법으로 구하였고 요구되는 입력자료는 실험을 통하여 획득하였다. 수동 휠체어 추진에 필요한 상지 거동의 운동학적 자료는 3차원 동작분석 시스템에서 추출하였고 역동역학 모델의 외력에 해당하는 운동역학적 자료는 브레이크식 다이나모미터에서 추출하였다. 역동역학 모델을 이용한 해석을 통하여 수동 휠체어 추진에 따른 상지 관절의 회전각과 관절 토크를 구하였다. 개발된 모델은 상지 관절에 관한 생체역학적 해석 도구이며 적은 노력으로 3차원 역동역학 모델로 확장하는 토대가 된다. Manual wheelchair propulsion can lead to pain and injuries of users due to mechanical inefficiency of wheelchair propulsion motion. The kinetic analysis of the upper limbs during manual wheelchair propulsion needs to be studied. A two dimensional inverse dynamic model of upper limbs was developed to compute the joint torque during manual wheelchair propulsion. The model was composed of three segments corresponding to upper arm, lower arm and hand. These segments connected in series by revolute joints constitute open chain mechanism in sagittal plane. The inverse dynamic method is based on Newton-Euler formalism. The model was applied to data collected in experiments. Kinematic data of upper limbs during wheelchair propulsion were obtained from three dimensional trajectories of markers collected by a motion capture system. Kinetic data as external forces applied on the hand were obtained from a dynamometer. The joint rotation angles and joint torques were computed using the inverse dynamic model. The developed model is for upper limbs biomechanics and can easily be extended to three dimensional dynamic model.
김세윤(S. Y. Kim),송성재(S. J. Song),서현배(H. B. Seo) 유공압건설기계학회 2010 드라이브·컨트롤 Vol.7 No.4
The flow regulators we widely use have some disadvantages. They have a constant flow within each regulator and an inaccuracy with extruding capillary. In this study, we have developed a new type of regulator which was made up of two different capillary tubes overlapped each other. The developed regulator can vary and control the amount of flow. The design parameters of the developed regulator are obtained by using theanalytical software. We have proved that the developed regulator can control flow properly through making a trial product and experiment.