http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
박문식 대한기계학회 2019 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.33 No.9
A simple estimation method of equivalent porosity and strength of scrapped aluminum die-casting floor panel is suggested in which various defects like pores can be allowed. During shop practice of processing die-casting parts, equivalent porosity is evaluated by the ratio of linear stiffness from the simple test to the analytical stiffness value. Porosity equation is derived from the inclusion theory. Then using Mori-Tanaka method the porosity value is used to find an elasto-plastic stress-strain curve for the porous material. In this paper Hollomon equation is used to describe the strain hardening effect of the die-casting material. Finally, the stress-strain curve for the porous material is used to calculate strength of die-casting part that captures the nonlinearity of the porous material. A facility die-casting floor panel is chosen to verify the proposed method. The result is accurate and adequate to the test result.
박문식,JongPilPark,So-Hee Yun,Jae-Un Lee,Joong-Keun Kim,Na-Eun Lee,Ji-Eun Song,Shin-Eun Lee,Sung-Hee John,JiHyunLim,Jay-Young Rhew 대한심장학회 2012 Korean Circulation Journal Vol.42 No.12
A paradoxical embolism is defined as a systemic arterial embolism requiring the passage of a venous thrombus into the arterial circulato -ry system through a right-to-left shunt, and is commonly related to patent foramen ovale (PFO). However, coexisting pulmonary embo-lisms, deep vein thromboses (DVT), and multipe systemic arterial embolisms, associated with PFO, are rare. Here, we report a patient who had a cryptogenic ischemic stroke, associated with PFO, which is complicated with a massive pulmonary thromboembolism, DVT, and re-nal infarctions, and subsequently, the patient was treated using a thrombolytic therapy.
박문식,서영성 대한기계학회 2013 JOURNAL OF MECHANICAL SCIENCE AND TECHNOLOGY Vol.27 No.2
A plastic strain gradient theory incorporating the geometrically necessary dislocation density based on the low order displacement finite element method is proposed for calculation of the hardness value by Berkovich indentation. The obtained analysis results by this work are found to be in good agreement with the experimental data. Three-dimensional modeling technique of Berkovich indentation is also suggested. An empirical coefficient that includes the strain gradient effect into the yield stress formula is introduced and determined by reviewing area factors and hardness curves generated from the analyses. As pile-up occurs, classical plasticity theory gives a higher area factor and lower hardness value than those from experiment. However the strain gradient plasticity theory used in this work gives corrected area factor and hardness values. Dislocation density plots are generated that can explain the size effect during indentation and the availability of the three-dimensional modeling of Berkovich indentation.
박문식,김남규,이선경,서지혜,박동희 한국폐기물자원순환학회 2014 한국폐기물자원순환학회 학술대회 Vol.2014 No.11
하수처리장 운영 시 생성되는 하수슬러지는 하수처리장에서 배출되는 폐기물의 대부분을 차지한다. 발생한 하수슬러지의 처리는 퇴비화, 사료화, 매립, 소각, 에너지화, 재활용, 해양투기 등의 여러 방법으로 이루어졌다. 그러나 2013년 런던 협약 발효에 따라 처리 방법 중 30~40%를 차지하던 해양투기가 금지되었다. 해양투기 다음으로 많이 사용된 방법은 육상매립이나, 육상매립의 경우 부지 확보가 점차 어려워지고 환경규제의 강화로 매립하는 양이 감소되고 있다. 따라서 하수처리장에서 발생하는 슬러지를 최소화 하는 동시에 자원으로 활용할 수 있는 적정 기술의 필요성이 대두되고 있다. 여러 적정 기술 중 혐기성소화는 하수슬러지를 혐기 미생물을 이용하여 메탄을 생성하는 가용화하는 대표적인 방법이다. 혐기소화조 운영에 있어서 하수슬러지를 바로 투입하여 처리하는 경우 낮은 소화 효율을 보이므로 소화조 전단에 전처리 기술을 배치하여 소화 효율을 향상 시킬 수 있다. 이런 전처리 기술에는 효소에 의한 생물학적 처리, 초음파, 오존, 원심분리, 액체전단, 분쇄의 기계적 처리, 산화, 알칼리에 의한 화학적 처리, 열처리가 있다. 그 중 열전처리 공정은 슬러지의 부피 감량과 불필요한 화합물의 분해 뿐만 아니라 슬러지 내의 병원균도 제거 가능한 장점을 가진다. 본 연구를 통해 열전처리 공정의 특성을 확인하였으며 공정 이후 생성된 물질의 특성도 평가하였다. 실험은 회분식 반응기에서 진행 되었으며, 혐기조건을 만든 후 열을 가하여 운전하였다. 실험 조건은 온도, 시간, 슬러지 함량에 따라 설정하였다. 각 조건에 따른 시료를 분석한 결과 건조 중량 1g을 기준으로 휘발성유기물질의 초기 농도가 0.67 g 일 때 최대 0.002 g까지 감소가 확인되었다. 감소한 휘발성 유기물질은 용존 유기물 형태로 변경되었고, COD 0.071 - 0.158 g-C/L 또는 TC 0.04 - 0.085 g-C/L 의 증가가 확인되었다. 이외에 TN은 3 - 22 mg-N/L의 증가가 확인되었고, 질산성 질소 또는 아질산성 질소는 미량 발견되었으며, 암모니아 형태의 N이 0.34 - 10.36 mg-N/L로 존재하는 것이 확인되었다.
박문식,Park, Mun-Sik 대한기계학회 2000 大韓機械學會論文集A Vol.24 No.4
In design and manufacturing airframe structures which are composed of a lot of sub-assemblies and large complex profile shapes it is difficult to reduce so called hardware variations. Accordingly cost increasing factors for manufacturing airframe parts are much more than other machine parts because of the variability of fabricated details and assemlies. To improve cost and quality, accurate assembly methods and DPD techniques are proposed in this paper which are based upon using CAD/CAM techniques, the concept of KC's and the coordinated datum and index throughout the design, tooling, manufacturing and inspection. The proposed methods are applied to produce fuselage frame assemblies and related engineering aspects are described regarding the design of parts and tools in the context of concurrent digital definition. First articles and consequent mass production of frame assemblies shows a great improvement of the process capability ratio from 0.7 by the past processes to 1.0 by the proposed methods in addition to the cost reduction due to the less number of tools, reduced total assembly times and the space compaction needed by massive inventory. The need to achieve better Cpk, however, and future studies to be investigated will be addressed briefly.