http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
Mg<sub>2</sub>SiO<sub>4</sub>/Glass Composite계 세라믹스를 이용한 음이온 발생용 후막형 클러스터
여동훈,신효순,홍연우,Yeo, Dong-Hun,Shin, Hyo-Soon,Hong, Youn-Woo 한국전기전자재료학회 2010 전기전자재료학회논문지 Vol.23 No.2
The eco-friendly technologies have been extended as matter of international concern due to various diseases and syndromes according to an environmental pollution. In this study, we have manufactured a ceramic cluster with thick film type for anion generation equipment which is maximized anion but minimized ozone contents generated. To develop the formulation of ceramic cluster, we conducted the $Mg_2SiO_4$ powders doped with 10 vol% glass frits as Na-Zn-B-O system and sintered at $1050^{\circ}C$ for 2 hours in air for starting materials and investigated the matching properties between the Ag-Pd electrode and the starting materials. The sintered sample for the composition of cluster has 6.7 of dielectric constant and 32 kV/mm of withstand voltage. The yield of anions was measured according to an electrode pattering, discharge gap between electrode, and thickness of electrode protective layer in the cluster of thick film type. We have manufactured the ceramic clusters with optimized thick film structure that have an anion over a hundred particles and the ozone of 0.6 ppb generated.
권혁중,여동훈,신효순,Kwon, Hyeok-Jung,Yeo, Dong-Hun,Shin, Hyo-Soon 한국전기전자재료학회 2013 전기전자재료학회논문지 Vol.26 No.1
The properties of LTCC green sheets formed by the MLS-22 powder of NEG Inc. were investigated for acrylic binders with different PVB and Tg in the variation of temperature. The elongation of the green sheets showed large variation depending on the temperature, and was rapidly decreased near the Tg of the sheets. With the increase of the ratio of plasticizer/binder (P/B), large elongation of the sheets was observed due to the decrease of the Tg. In the stacking process of the multilayer ceramic, the optimal control of the temperature is highly required depending on the Tg of the binder and the ratio of P/Buniform coating.
이원준,여동훈,신효순,정대용,Lee, Won-Jun,Yeo, Dong-Hun,Shin, Hyo-Soon,Jeong, Dea-Yong 한국전기전자재료학회 2014 전기전자재료학회논문지 Vol.27 No.12
In solid oxide fuel cell system, yttria-stabilized zirconia is generally adopted as the electrolyte, which has high strength and superior oxygen ion conductivity, and the air electrode and the fuel electrode are attached to this. Recently, new structure of 'layered planar SOFC module' was suggested to solve the reliability problem due to the high temperature stability of a sealing agent and a binding material. In this study to materialize the air electrode in a layered planar SOFC module, the LSM ink was coated to form homogeneous electrode in the channel after the ink preparation. As the porosity control agent, PMMA or active carbon powder was adopted with use of a commercial dispersant in ethanol. The optimal amounts of both the porosity control agents and the dispersant were determined. Four (4) vol% of the dispersant for the LSM-PMMA case and 15 vol% for LSM-carbon powder showed the lowest viscosities respectively to indicate the best dispersed states of the slurries. With PMMA and carbon powder, sintered LSM ink shows the relatively homogeneous distributions of pores and with increases of the agents, the porosities increased in both cases. From this, it can be thought that the amount of the PMMA or carbon powder could be used to control the porosity of the LSM ink.