자외선 조사간격이 브로일러 병아리 다리 피부의 비타민 D3 함량에 미치는 영향

장윤환(Y . H . Chiang),조인호(I . H . Cho),여영수(Y . S . Yeoh),이은택(E .T . Lee),배은경(E . K . Bae),김중달(J . D . Kim),M . F . Holick(M . F . Holicka) 한국영양사료학회 1993 韓國營養飼料學會誌 Vol.17 No.6

도금슬러지 시멘트고형화에서의 강도 및 안정화 증진

윤현식,강민성,이두진,신응배,배우근,유도윤 漢陽大學校 環境工學硏究所 1997 環境科學論文集 Vol.18 No.-

본 연구에서는 도금폐수처리공정에서 발생하는 실 슬러지를 대상으로 현장에서 적용이 가능한 시멘트고형화 및 안정화효율 증진방안을 찾기 위하여 실내 실험을 통해 1) 슬러지내의 수분이 시멘트의 수화반응에 미치는 영향, 2) 교반시간증가에 의한 고화체의 강도향상 및 용출억제효과, 그리고 3) 첨가제를 이용한 고형화효율 증대를 중점적으로 살펴 보았다. 실슬러지의(습윤슬러지) 자체가 함유한 수분이 시멘트수화반응에 미치는 영향을 살펴보기 위하여 슬러지를 건조시킨 후 물을 첨가하여 시멘트모르터내에 자유수를 증가시킨 결과 습윤슬러지를 그대로 고형화 한 경우보다 동일한 수분에서 2배정도의 높은강도를 얻을 수 있었다. 교반시간을 증가시킬수록 강도와 용출성이 점차 향상되어 10분정도의 교반시간에서 우수한 결과를 얻었으며, 특히 습윤슬러지의 경우 그 효과가 두드러지게 나타났다. 첨가제사용에 따른 효율평가 실험은 Silica fume, 황산반토, Zeolite, EDTA를 대상으로 실시하였으며 이중 Silica fume이 강도와 용출억제면에서 가장 효과가 좋았다. 최적배합비는 습윤슬러지의 경우 첨가비(첨가제/시멘트)0.25∼0.5에서 가장 우수하였고, 0.05∼0.1에서 가장 좋은 용출효과를 나타내었다. 이는 Silica fume이 중금속에 의한 시멘트수화 방해작용을 억제하고 중금속이온을 불용성의 화합물로 고정하기 때문으로 사료된다. The Solidification /Stabilization (S/S) using the cement as a binder is widely used because of its stability and low cost. For cement-based S/S, however, the S/S efficiency in terms of strength and contaminant immobilization varies significantly according to the treated waste types and operational conditions. In this research real planting sludges were choosen for the S/S experiments in order to increase the applicability of the results in the actual site. Especially, the study focused on the effects of 1) the moisture of sludge on the hydration-reaction of cements, 2) the increased mixing time on the enhancement of the strength and immobilization, and 3) using the binder additives on the S/S efficiency. The compressive strength and leachability of the heavy metals (CU, Cd, Pb, Cr, and Zn) from the solidified materials were measured for evaluating the S/S efficiency. Drying the sludge and putting water, keeping the moisture content the same as the original sludge, into the cement mortar for supplying free-water increased the compressive strength of the solidified material by appoximately two times. Prolonged mixing of the sludge-cement mixture increased, particually in the wet sludges, the strength of the solidified material and retarded the mobility of heavy metals from the sludge. Good results obtained at ten minutes of mixing. In the experiments using the additives, silica fume gave superior results with the strength and immobilization to other additives (Al₂(SO₄)₃Zeolite, EDTA) tested. In the wet sludges, the optimum additive/cement ratio was 0.25-0.5 for strength and 0.05-0.1 for immobilization. It was suspected that the silica fume prevented the interference of heavy metals on the hydration reaction of cement and fixed the heavy metal ions into insoluble complexes.

각종 사료의 소화율에 미치는 축종의 영향

김상철 ( S C Kim ),배동호 ( D H Bae ),김강식 ( K S Kim ),박용윤 ( Y Y Park ),이종원 ( J W Lee ),박신호 ( S H Park ) 한국축산학회 1971 한국축산학회지 Vol.13 No.2

Digestibility comparisons were made using Korean native cattle, native goat, sheep, rabbit, pig and poultry with two different roughages, two different concentrates and soybean oil cake. a. Digestibility difference for roughages There were no significant differences in digestion coefficients, D.C.P. and T.D.N, content, except N.F.E in the case of good quality hay, and crude protein and crude fat in the case of poor quality hay between Korean native cattle, native goat and sheep. However, there were significant differences between the animals mentioned above and rabbit in all digestion coefficients, D.C.P. and T.D.N. content, except crude protein and crude fat. b. Digestibility difference for concentrates There were significant differences in digestion coefficients and digestible nutrients between the animal used. Digestibility of sheep and native goat, and pig and poultry showed similar trend. Rabbit Showed the highest T.D.N. content in the case of corn. However, this superiority in digestibility disappeared in the case of wheat bran. c. Digestibility difference for soybean oil cake Significant differences in digestibility of crude fat, N.F.E. crude fiber, and T.D.N. content were found between ruminants and monogastric animals. No significant differences were observed in digestibility of crude protein and D.C.P. content between the animals used.

Measurement of vector boson plusD*(2010)+meson production inp¯pcollisions ats=1.96 TeV

Aaltonen, T.,Amerio, S.,Amidei, D.,Anastassov, A.,Annovi, A.,Antos, J.,Apollinari, G.,Appel, J. A.,Arisawa, T.,Artikov, A.,Asaadi, J.,Ashmanskas, W.,Auerbach, B.,Aurisano, A.,Azfar, F.,Badgett, W.,Bae American Physical Society 2016 Physical Review D Vol.93 No.5

<P>A measurement of vector boson (V) production in conjunction with a D*(2010)(+) meson is presented. Using a data sample corresponding to 9.7 fb(-1) of proton-antiproton collisions at center-of-mass energy root s = 1.96 TeV produced by the Fermilab Tevatron, we reconstruct V + D*+ samples with the CDF II detector. The D*+ is fully reconstructed in the D*(2010)(+) -> D-0 (-> K-pi(+))pi(+) decay mode. This technique is sensitive to the associated production of vector boson plus charm or bottom mesons. We measure the ratio of production cross sections sigma(W + D*) = sigma(W) = [1.75 +/- 0.13(stat) +/- 0.09(stat)]% and sigma(Z + D*)/sigma(Z) = [1.5 +/- 0.4(stat) +/- 0.2(stat)]% and perform a differential measurement of d sigma(W + D*)/dp(T)(D*). Event properties are utilized to determine the fraction of V + D*(2010)(+) events originating from different production processes. The results are in agreement with the predictions obtained with the PYTHIA program, limiting possible contribution from non-standard-model physics processes.</P>

Solid mass flux in a chemical-looping process for hydrogen production in a multistage circulating moving bed reactor

Hong, Y.S.,Kang, K.S.,Park, C.S.,Kim, S.D.,Bae, J.W.,Nam, J.W.,Lee, Y.,Lee, D.H. Pergamon Press ; Elsevier Science Ltd 2013 INTERNATIONAL JOURNAL OF HYDROGEN ENERGY - Vol.38 No.14

We studied the solid flow characteristics of a multistage circulating moving bed reactor manufactured to produce high purity H<SUB>2</SUB> using a chemical-looping process at high temperature. The reactor was constructed of stainless steel 304 and comprised an inclined fuel reactor ((bottom: 0.07 m, top: 0.16 m) x 0.06 x 1 m<SUP>3</SUP>), a steam reactor (0.16 x 0.06 x 1.4 m<SUP>3</SUP>), a riser (0.03 x 0.06 x 3.8 m<SUP>3</SUP>), two loop-seals (0.03 x 0.06 m<SUP>2</SUP>), and a cyclone. Zirconia beads (d<SUB>p</SUB> = 186 m, ρ<SUB>p</SUB> = 3720 kg/m<SUP>3</SUP>, U<SUB>mf</SUB> = 4.95 x 10<SUP>-2</SUP> m/s, Geldart classification B Group) were used as the bed material. To distribute compressed air, a bubble cap was used as the distributor. Solid mass flux appeared at 6.2-56.4 kg/m<SUP>2</SUP>s and the solid mean residence time appeared 92.5-889.3 s in the steam reactor and 75.3-717.7 s in the fuel reactor. Solid mass flux increased with increasing inlet gas velocity into the loop-seal, temperature and the bed height of the steam reactor. However, the solid mean residence time decreased with increasing inlet gas velocity into the loop-seal and the bed height of the steam reactor.

Measurement of the D+ -meson production cross section at low transverse momentum in pp¯ collisions at s=1.96 TeV

Aaltonen, T.,Amerio, S.,Amidei, D.,Anastassov, A.,Annovi, A.,Antos, J.,Apollinari, G.,Appel, J. A.,Arisawa, T.,Artikov, A.,Asaadi, J.,Ashmanskas, W.,Auerbach, B.,Aurisano, A.,Azfar, F.,Badgett, W.,Bae American Physical Society 2017 Physical Review D Vol.95 No.9

<P>We report on a measurement of the D+ -meson production cross section as a function of transverse momentum (p(T)) in proton-antiproton (p (p) over bar) collisions at 1.96 TeV center-of-mass energy, using the full data set collected by the Collider Detector at Fermilab in Tevatron Run II and corresponding to 10 fb(-1) of integrated luminosity. We use D-broken vertical bar -> K- pi(broken vertical bar) pi(broken vertical bar) decays fully reconstructed in the central rapidity region broken vertical bar y broken vertical bar < 1 with transverse momentum down to 1.5 GeV/c, a range previously unexplored in p<(p)over bar> collisions. Inelastic p (p) over bar -scattering events are selected online using minimally biasing requirements followed by an optimized offline selection. The K- pi(+) pi(+) mass distribution is used to identify the D+ signal, and the D+ transverse impact-parameter distribution is used to separate prompt production, occurring directly in the hard-scattering process, from secondary production from b-hadron decays. We obtain a prompt D+ signal of 2950 candidates corresponding to a total cross section sigma(D+), 1.5 < P-T < 14.5 GeV/c, vertical bar y vertical bar < 1) = 71.9 +/- 6.8 (stat) +/- 9.3 (syst) mu b.While the measured cross sections are consistent with theoretical estimates in each p(T) bin, the shape of the observed p(T) spectrum is softer than the expectation from quantum chromodynamics. The results are unique in p<(p)over bar> collisions and can improve the shape and uncertainties of future predictions.</P>

Progress in the development of heating systems towards long pulse operation for KSTAR

Kwak, J.G.,Bae, Y.D.,Chang, D.H.,Chang, D.S.,Hong, B.G.,Hwang, C.K.,In, S.R.,Jeong, S.H.,Jin, J.T.,Jung, K.S.,Kim, B.R.,Kim, J.,Kim, S.K.,Kim, T.S.,Lee, D.W.,Lee, K.W.,Oh, B.H.,Seo, C.S.,Seo, M.S.,Yoo International Atomic Energy Agency 2007 Nuclear fusion Vol.47 No.5

<P>Construction of the Korea superconducting tokamak advanced research (KSTAR) tokamak is in its final phase. For the long-pulse KSTAR discharges, the ion cyclotron range of frequencies (ICRF) and neutral beam injection (NBI) heating systems are expected to play important roles through a selective heating of ions and electrons, control of the plasma pressure and current profiles, a core fuelling and beam diagnostics for the KSTAR. In addition, the ICRF system is expected to be used for possible discharge cleaning and assisting in the tokamak startup. In this paper, the recent progress in the development of the ICRF and the NBI heating systems is described. The four-strap ICRF antenna has been successfully tested for a voltage up to 41 kV for a pulse length of 300 s (to 46 kV for 20 s) in a test chamber. A prototype KSTAR NBI system has been developed. At present, the system has successfully produced a 1 MW beam power for 200 s and a 3.5 MW output beam power for 4 s.</P>

Structural basis for differential activities of enantiomeric PPARγ agonists: Binding of S35 to the alternate site

Jang, J.Y.,Koh, M.,Bae, H.,An, D.R.,Im, H.N.,Kim, H.S.,Yoon, J.Y.,Yoon, H.J.,Han, B.W.,Park, S.B.,Suh, S.W. Elsevier Science 2017 Biochimica et biophysica acta. Proteins and proteo Vol.1865 No.6

<P>Peroxisome proliferator-activated receptor gamma (PPAR gamma) is a member of the nuclear receptor superfamily. It functions as a ligand-activated transcription factor and plays important roles in the regulation of adipocyte differentiation, type 2 diabetes mellitus, and inflammation. Many PPAR gamma agonists bind to the canonical ligand-binding pocket near the activation function-2 (AF-2) helix (i.e., helix H12) of the ligand-binding domain (LBD). More recently, an alternate ligand-binding site was identified in PPAR gamma LBD; it is located beside the 52 loop between the helices H2 ' and H3. We reported previously that the chirality of two optimized enantiomeric PPAR gamma ligands (S35 and R35) differentiates their PPAR gamma transcriptional activity, binding affinity, and inhibitory activity toward Cdk5 (cyclin-dependent kinase 5)-mediated phosphorylation of PPAR gamma at Ser245 (in PPAR gamma 1 numbering; Ser273 in PPAR gamma 2 numbering). S35 is a PPAR gamma phosphorylation inhibitor with promising glucose uptake potential, whereas R35 behaves as a potent conventional PPAR gamma agonist. To provide a structural basis for understanding the differential activities of these enantiomeric ligands, we have determined crystal structures of the PPAR gamma LBD in complex with either S35 or R35. S35 and R35 bind to the PPAR gamma LBD in significantly different manners. The partial agonist S35 occupies the alternate site near the Omega loop, whereas the full agonist R35 binds entirely to the canonical LBP. Alternate site binding of S35 affects the PPAR gamma transactivation and the inhibitory effect on PPAR gamma Ser245 phosphorylation. This study provides a useful platform for the development of a new generation of PPAR gamma ligands as anti-diabetic drug candidates.</P>

Comparison of 90‐day case‐fatality after ischemic stroke between two different stroke outcome registries using propensity score matching analysis

Yu, K‐,H.,Hong, K‐,S.,Lee, B‐,C.,Oh, M‐,S.,Cho, Y‐,J.,Koo, J‐,S.,Park, J‐,M.,Bae, H‐,J.,Han, M‐,K.,Ju, Y‐,S.,Kang, D‐,W.,Appelros, P. Blackwell Publishing Ltd 2011 Acta neurologica Scandinavica Vol.123 No.5

<P>Yu K‐H, Hong K‐S, Lee B‐C, Oh M‐S, Cho Y‐J, Koo J‐S, Park J‐M, Bae H‐J, Han M‐K, Ju Y‐S, Kang D‐W, Appelros P, Norrving B, Terent A. Comparison of 90‐day case‐fatality after ischemic stroke between two different stroke outcome registries using propensity score matching analysis. 
Acta Neurol Scand: 2011: 123: 325–331. 
© 2010 John Wiley & Sons A/S.</P><P><B>Background – </B> It has not been clarified whether the disparity in ischemic stroke outcome between populations is caused by ethnic and geographic differences or by variations in case mix. Propensity score matching (PSM) analysis can overcome some analytical problems but is rarely used in stroke outcome research. This study was to compare the ischemic stroke case‐fatality between two PSM cohorts of Sweden and Korea.</P><P><B>Methods – </B> Prognostic variables related to baseline characteristics and stroke care were included in our PSM model. Then, we selected 7675 Swedish and 1220 Korean patients with ischemic stroke from each stroke registers and performed one‐to‐one matching based on propensity scores of each patient.</P><P><B>Results – </B> After PSM, all measured variables were well balanced in 1163 matched subjects, and the 90‐day case‐fatality was identical 6.2% (HR 0.997, 95%CI 0.905–1.099) in Sweden and Korea.</P><P><B>Conclusions – </B> No difference is found in the 90‐day case‐fatality in propensity score‐matched Swedish and Korean patients with ischemic stroke.</P>

Ahnak functions as a tumor suppressor via modulation of TGFβ/Smad signaling pathway

Lee, I H,Sohn, M,Lim, H J,Yoon, S,Oh, H,Shin, S,Shin, J H,Oh, S-H,Kim, J,Lee, D K,Noh, D Y,Bae, D S,Seong, J K,Bae, Y S Macmillan Publishers Limited 2014 Oncogene Vol.33 No.38

We provide detailed mechanisms of Ahnak-mediated potentiation of transforming growth factor β (TGFβ) signaling, which leads to a negative regulation of cell growth. We show that Smad3 interacts with Ahnak through MH2 domain and that Ahnak stimulates Smad3 localization into nucleus leading to potentiating TGFβ-induced transcriptional activity of R-Smad. Moreover, overexpression of Ahnak resulted in growth retardation and cell cycle arrest through downregulation of c-Myc and cyclin D1/D2. We describe results from analyses of Ahnak<SUP>−/−</SUP> mouse model expressing middle T antigen in a mammary gland-specific manner (MMTV<SUP>Tg/+</SUP>Ahnak<SUP>−/−</SUP>), which showed significantly progressed hyperplasia of mammary glands compared with MMTV<SUP>Tg/+</SUP>Ahnak<SUP>+/+</SUP>. Finally, we screened multiple human breast cancer tissues and showed that the expression of Ahnak in cancer tissues is lower than that in control tissues by 50%. Taken together, these data indicate that Ahnak mediates a negative regulation of cell growth and acts as novel tumor suppressor through potentiation of TGFβ signaling.