http://chineseinput.net/에서 pinyin(병음)방식으로 중국어를 변환할 수 있습니다.
변환된 중국어를 복사하여 사용하시면 됩니다.
X 선 및 전자선회절법에 의한 천연셀룰로오스의 결정구조 해석
김남훈 한국목재공학회 1996 목재공학 Vol.24 No.3
Cellulose I에서 Cellulose II로의 결정변태기구를 X선 및 전자선 회절법과 현미경적 방법을 이용하여 구명하였다. X선 회절 결과, N3-Cellulose I을 고온에서 수세할 경우 Cellulose I과 Cellulose II의 혼합형 회절도가 저온에서 수세할 경우 Na-cellulose IV의 회절도가 얻어졌다. 전자선회절 결과, 고온수세의 시료는 Cellulose 1과 Cellulose II 의 혼합형이, 저온수세의 시료는 Cellulose II의 회절도가 얻어졌다. 또한 고온수세 시료의 전자선회절도로부터 섬유벽의 내측부가 외측부보다 재생 Cellulose I의 양이 많은 것이 확인되었다. 따라서 알칼리 팽윤시 섬유벽내에는 불완전한 팽윤이 발생하는데 그 정도는 내측부가 더욱 심한 것으로 생각된다. 이때 형성되는 불완전한 Na-cellulose I은 고온수세의 경우는 탈수에 의해 Cellulose I로, 저온수세의 경우는 수화에 의해 Cellulose II로 변태되지만 완전히 팽윤된 Na-cellulose I은 Cellulose I로 재생될 수 없는 것으로 생각된다. 현미경적 실험결과 mereerization과정에서 cellulose 분자쇄의 packing이나 conformation의 변화와 관련하여 microfibril의 흐트러짐은 발생하지 않는 것으로 생각되었다.
마그네트론 스퍼터링법으로 증착시킨 TiC 박막의 물리적, 전기적 특성에서 RF 파워의 영향
김남훈,박용섭,Kim, Nam-Hoon,Park, Yong Seob 한국전기전자재료학회 2014 전기전자재료학회논문지 Vol.27 No.7
TiC thin films were deposited on Si wafer by unbalanced magnetron sputtering (UBMS) system with two targets of graphite and titanium. During the TiC sputtering, the RF power was varied from 100 W to 175 W and the physical and electrical properties of TiC films were investigated. The hardness and rms surface roughness of TiC films were improved with increasing RF power and the maximum hardness about 24 GPa and the minimum rms surface roughness about 1.2 nm were obtained. The resistivity of TiC films was decreased with increasing RF power. Consequently, the physical and electrical properties of TiC film wewe improved with increasing RF power.
김남훈,이용성,Kim, Nam-Hoon,Lee, Yung-Sung 대한기계학회 1996 大韓機械學會論文集A Vol.20 No.12
In order to clarify the effects of nonmetallic inclusion contents insteels (SM45C & SCM440) on the tool life, cutting experiment was performed under various cutting conditions. Tool life, cutting force, roughness of machined surface and cutting mechanism are examined on these two kinds of steel. The following conclusions were obtained from the analysis (1) Cutting force of the steels was not affected by chemical component and nonmetallic inclusion. (2) If the rate of amount, Ca/S has a value grater than about 0.2 and addition of less amount of Al, Mn, tool wear of tips decreasesinturning. (3) It is also proved that higher contents of nonmetallic inclusion improve roughness of the surface. (4) Less amount of Ca, higher amount of S, Mn and Al improve the chip breakability.